NEUATION iTherm CH25 Heating Incubator User Manual

INTRODUCTION

This is a mini incubator that can control the temperature in the chamber for incubation experiments. The temperature ranges from -15°C from ambient to 60°C. This equipment is of 22L capacity to hold different flasks up to 2L.

NOTE: This device, cools based on the ambient temperature of the room. It is not designed to be used outside in the heat as it will not maintain the temperature in the camber that the samples needed. It works best when used indoors in a cool room.

INTENDED USE

This instrument is to serve the temperature control and homogeneous controlled environment required for cell culture or for biological & nonbiological samples to be incubated. This instrument is intended to use indoors only & should be used by trained staff in the laboratory.

FEATURES

• Digital Temperature control from Ambient -15 to 60°C
• Compact footprint, usable on small bench space
• Accepts multiple types of flask up to 2L
• Internal power outlet for installing small shaker, mixer, or other instruments

TECHNICAL SPECIFICATIONS

INSTALLATION

Position the appliance and allow it to stand for two or three hours (ten hours in summer) before it is turned on for the first time to allow the system to settle. Do not position next to any heat source e.g. cooker, boiler, or in direct sunlight, etc.
A clearance of 5 inches must be left between the sides of the appliance and any adjacent cabinets or walls to allow for adequate air circulation. The appliance is not designed for recessed installation meaning it should not be built into the wall.

Install on a good firm level surface and any unevenness of the surface should be corrected prior to installation

SAFETY PRECAUTIONS

Do not use this item near water where it can be exposed to getting wet. Make sure the item is only operated from the type of power source indicated on the label. Do not add any attachments that were not originally included with the item as they may cause harm to the machine and become a safety issue. Also, make sure power cords are placed in a position where they will not to waked on or damaged. Lastly, make sure not to overload power outlets by plugging in too many devices in one socket. Unplug the unit when not in use for a long period of time.

OPERATING THE INSTRUMENT

1. The open front of the unit and place samples inside.
2. Plug the adaptor into the machines and then put the electric plug into the wall.
3. Turn the power switch to “On” or “Cool”.
4. Set the desired temperature ranging from -15°C from ambient (can go as low up to 2°C) to 60°C.
5. The temperature can be changed by pressing “UP” for increment & “DOWN” for The changed values get saved automatically.

CLEANING

Make sure to remove the machine from the good plug before cleaning and do not use abrasive cleaners. We suggest using a damp cloth

WARRANTY STATEMENT

This product is warranted to be free from defects in material and workmanship for a period of two (2) years from the date of purchase. Your product will be duly repaired upon prompt notification in compliance with the following conditions :

The warranty is invalidated by any non-factory modification, which will immediately terminate all liabilities on us for the products or damages caused by its use. The customer shall be responsible for the product or use of products as well as any supervision required for safety. If requested the products must be returned to the distributor in a well-packed and insured manner and all shipping charges must be paid.

NOTE: Some states do not allow limitations on the length of implied warranties or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights. This warranty is given expressly in lieu of all other warranties, expressed or implied. intended purpose and there are no other remedies or warranties, implied, that extend beyond the description on the face of the agreement. This warranty is only applicable to the original purchaser.
Products received without proper authorization will not be processed for warranty or service. All items returned for service should be sent with postage prepaid in the original packaging or another suitable packaging, padded to avoid damage. We will not be responsible for damage incurred by improper packaging.

NOTE: This warranty is valid only if the warranty is registered with the supplier within 30 days from the date of purchase.

For your reference, make a note of the serial number, date of purchase, and supplier here.

Serial No.:                                                       Purchase Date:
Supplier:

PRODUCT DISPOSAL

In case the product is to be disposed of, the relevant legal regulations are to be observed.

Information on the disposal of electrical and electronic devices in the European Community.

The disposal of electrical devices is regulated within the European Community by national regulations based on EU Directive 2012/19/EU on waste electrical and electronic equipment (WEE E). According to these regulations, any devices supplied after 13.06.05 in the business to business sphere, to which this product is assigned, may no longer be disposed of in the municipal or domestic waste. They are marked with the following symbol to indicate this.
As disposal regulations within the EU may vary from country to country, please contact your supplier if necessary.

Negation Technologies Pvt. Ltd.
Plot No. 15, GIDC Electronic Park SEZ Kolavada Road, Gandhinagar – 382026, Gujarat, India
Website:www.neuation.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>