moa MF1 Milk Frother Instruction Manual

moa MF1 Milk Frother

BEFORE USE

Before use, please read this manual carefully.
Only connect the appliance to an earthed wall socket.
This appliance is for household use only. When using electrical appliances, basic safety precautions should always be followed to avoid fires, electric shocks, burns, or other injuries and damage. Read these operating and safety instructions carefully.
WARNING: The blades of the knife are extremely sharp. Handle them with caution.

IMPORTANT SAFEGUARDS

1. Before you start using the product please check the power cord is in good condition and all P.arts are intact. If
   it is damaged, please do not use the milk frother and contact customer service team to solve the problem.

2. When it is in use or cleaning, do not immerse any part of the machine, base or plug in water or other liquids to prevent electric shock. It cannot be washed in the dishwasher to avoid short circuit.

3. Do not use this product near heat sources to avoid danger.

4. As the milk frothing piece and whisk are small in size please place them in a safe place to avoid being eaten by kids accidentally or lose.

5. The liquid volume cannot exceed the capacity scale in the cup, otherwise it will overflow.

6. Please use the machine on a flat and dry surface.

7. Unplug before replacing parts.

8. The milk frother can only be used with the power base
   provided in the package.

9. It is recommended to use whole milk for frothing (fat content 3%).

10. Milk can be heated up to 60 +2°C at most. This is the most
    ideal temperature, that is , it will not damage the molecular
    structure and nutritional content of the milk, and can increase
    the taste and tlavour without waiting too long.

11. Dry burning or over- temperature: it you power it on when there is no milk in the machine, the liner of milk trother may be overheated or burned. It is judged as dry burning when the temperature ot the liner is over 115°C dry burning protection will be activated, the machine will beep and stop working and shut down. It you need to start again, wait for the temperature to cool down and then you can operate again.

12. Connect the machine with the power supply, refill it with milk, and put it on the power base. It the tunction light does not turn on tor Is and there is no response, the power base and the body may have poor contact. You can rotate it to see it the machine and power base are properly connected.

PARTS & LOCATION

1. Lid
2. Frother
3. Liner
4. Control panel
5. Handle
6. Cover
7. Powerbase
8. Indicator tor hot trothing
9. Indicator for heating milk
10. Indicator tor cold trothing
11. Power button/ Select key

USING YOUR APPLIANCE

• Connect the base with power supply and pour the milk into the milk frother. Make sure that the amount of milk poured does not exceed the MAX mark. Put it on the power base and you will hear a beep. The three indicators are all on tor Is, then they will go out. Now it is in standby status.

• The working time of the machine is automatically adapted according
  to the volume of milk added and the original temperature of the milk. Hot trothing: In the standby state, press the power button once, the three tunction indicators light up, and hot trotting indicator flashes, indicating that hot trothing is selected. Atter 25 seconds the hot trothing indicator stays on and the other two indicators go out, and then the machine starts to work. Atter trothing is completed, the machine beeps and the hot frothing indicator light goes out, it stops working and returns to the standby state. When hot frothing is completed, the milk froth temperature is 60+2″C.
  Heating milk: In the standby state, press the power buton twice, the three function indicators light up, and the heating milk indicator flashes, indicating that heating milk is selected. After 25 seconds, the heating milk light indicator stays on, the other two indicators go out, and then the machine starts to work. Atter heating milk is completed, the machine beeps and the heating milk light indicator goes out, the machine stops working and returns to the standby state. Now the milk tempearture is 60+2°C.

• Cold frothing: In the standby state, press the power button three times, the three function indicators lights light up, and the cold frothing indicator flashes, indicating that cold frothing is selected. After 25 seconds, the cold milk trothing light stays on, the other two indicators go out, and then the machine starts to work. After cold trothing is completed, the machine beeps and the cold frothing indicator light goes out, it stops working and returns to the standby state. Now the milk is frothed and its temperature is same as before.

• Long press power button to cycle through the above functions. Cancel Selection: If you need to cancle the selection when the milk frother is working, you can press the power button, the tunction indicator goes out, and the milk froter returns to the standby state. If you need to re-select a function, press the power button in standby mode.

FUNCTIONS

• Function: Hot frothing
• Milk Capacity: MIN: 100ml
• Working Time: 90-120 sec
• MAX: 160ml
• Final Temprature: 60+5°C
• Function: Heating Milk
• Milk Capacity: MIN: 100ml MAX: 350ml
• Working Time: 120-160 sec
• Final Temprature: 60+5°C
• Function: Cold frothing
• Milk Capacity: MIN: 100ml MAX: 160ml|
• Working Time: 60+5°C
• Final Temprature: Room temprature

CLEANING AND STORAGE

• Separate the cup body from the power base and take out the lid before cleaning. Do not soak the body and power base in water and do not put it in the dishwasher for cleaning.

• Cup liner: Use cold or warm water and add an appropriate amount oF detergent to moisten a soft towel to clean the liner, then wipe it with
  a dry towel.

• Lid: Remove the lid from the cup, wash it with water, and dry it.

• Body: Wipe the surface with a wet towel, the dry with a dry towel.

• Froth/ whisk accessoreis: Remove them from the cup, rinse directly
  with water and dry, then store.

TROUBLESHOOTING

Problem:
The milk frother is not working
Cause

1. The adapter is not plugged in or the outlet is noi powered.
2. The machine is not properly placed on the power socket
3. The temperature ot the machine is too high.

Solution:

1. Reinsert the plug or change to a different socket.
2. Take out the body and put it in the power base correctly.
3. Rinse the inside ot the machine with cold water to lower the temperature.

Problem: The milk frothing is buring
Cause:

1. Too little or too much milk.
2. Jug is being reused and not cleaned.
3. The actual voltage is lower than the specitied one.

Solution:

1. Make sure the milk volume is between min and max capacity.
2. Always clean atter every Use.
3. Make sure the machine is connected with the proper voltage.

DISPOSAL

• Do not dispose of the device in normal domestic waste.
• Dispose of the device over a registered waste disposal tirm or through your communal waste disposal tacility.
• Observe the currently valid regulations. In case of doubt, consult your waste disposal tacility.

WARRANTY

Dear Valued Customer,
Thank you very much for purchasing a MOA product.
We wish you to inform you that this product is covered by a warranty which complies with all legal provisions concerning existing warranty and consumer rights in the country where the product was purchased.
Should you find any defect or malfunction of your MOA product, please contact the appropriate Customer Care Center. Sincerely yours,
The MOA Team

References

• MOA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>