moa 18D Electric Stove Induction Cooker Instruction Manual
- June 5, 2024
- moa
Table of Contents
Electric Stove 18D
Instruction Manual
www.moacolors.com
This product is only suitable for well insulated spaces or occasional use.
BEFORE USE
Before use, please read this manual carefully.
Only connect the appliance to an earthed wall socket.
This appliance is for household use only. When using electrical appliances,
basic safety precautions should always be followed to avoid fires, electric
shocks, burns, or other injuries and damage. Read these operating and safety
instructions carefully.
SAFETY INSTRUCTIONS
Only connect the appliance to an earthed wall socket.
This heater must be used on an AC supply only and the voltage marked on the
heater must correspond to the supply voltage.
Do not switch the appliance on until it is properly installed as described in
this manual.
Never use the appliance unsupervised when in use.
If you have to leave even for a short moment please stop the appliance.
Keep out of reach of children and do not allow them to operate this appliance.
Only use the appliance for domestic purposes and in the way indicated in these
instructions.
From time to time check the cord for damages.
Never use the appliance if the cord or any part of the appliance shows any
signs of damage.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Make sure the connection cord does not touch any hot surfaces.
Do not use the appliance outdoors
Do not use if you have wet hands.
Never use the appliance on or near hot surfaces.
Never move the appliance by pulling the cord.
Before cleaning the appliance, make sure it is unplugged from the power and
that it is completely cooled.
Do not clean the appliance with abrasive chemicals.
Never use accessories that are not recommended or supplied by the
manufacturer. It could cause danger to the user or damage to the appliance.
The heater should not be put under the jack directly.
SAFETY INSTRUCTIONS
Do not use this heater with a programmer, timer, or any other device that
switches the heater on automatically, since a fire risk exists if the heater
is covered or positioned incorrectly.
Do not use this heater in the immediate surroundings of a bath, a shower, or a
swimming pool.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children aged from 3 years and less than 8 years shall not plug in, regulate
and clean the appliance or perform user maintenance.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Cleaning and user maintenance shall not be made by children without supervision.
CAUTION — some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
WARNING: In order to avoid overheating, do not cover the heater.
PLACEMENT
This heater is designed to be placed on a hard, level surface. When
positioning, please keep the following points in mind:
If you are placing the heater in an alcove, make sure that there is at least
150mm of space on all sides to ensure good air circulation
The heater must not be located over a fixed electrical socket. The socket must
always be accessible in order to disconnect the heater from the electrical
supply for maintenance or when replacing a lamp.
Keep hearth rugs and other soft furnishings away from the front of the heater.
They could obstruct the free flow of hot air from the fan and damage both soft
furnishings and the heater.
LOCATION OF CONTROLS
The following switches are located under the front door of the heater.
1. Thermostat knob
2. Flame dimmer knob
3. Flame switch
4. Heater switch
5. Heater switch| – Adjust to maintain room temperature
– Adjust to set the flame intensity
– Turn on/off for flame/fuel effect
– Turn on/off for one of the 900W heat setting
– Turn on/off for one of the 900W heat setting
---|---
OPERATION INSTRUCTIONS
The following switches are located at the back of the heater.
- Insert plug into a mains socket
- Open the front door.
- Select the desired functions:
– Flame/fuel effect on/off (3)
– Low heat setting 900W (3 + 4)
– High heat setting 1800W (3 + 4+ 5)
– Heating and Flame effect (1 + 2 + 3 + 4 + 5)
Increase or decrease the flame intensity by clockwise or anti-clockwise
rotating the flame dimmer knob (2).
Rotate the thermostat knob clockwise or anti-clockwise to increase or decrease
the desired room temperature setting.
Notice: The heater will only work if the switch O/I is on and the thermostat is set above current room temperature.
SAFETY CUT-OFF
This appliance is fitted with a safety cut-off which will operate if the
heater overheats (e.g. Due to blocked air vents). For safety reasons, the
heater will NOT automatically reset.
To reset the appliance, disconnect the appliance from the main supply for at
least 15 minutes. Reconnect the supply to the mains and switch on the
appliance.
BULB REPLACEMENT
The bulb inside the heater is LEDs and not replaceable.
CLEANING AND CARE
Before cleaning, always remove the plug from the electrical socket.
Ensure that the unit is cool enough to work on.
Do not use harsh chemicals or solvents to clean this product and avoid using
abrasive cleaning agents.
The heater and glass parts need only to be wiped clean with a dry, soft cloth;
do not use polishes or abrasive materials.
Do not immerse in water or any liquid when you clean it.
Use a slightly damp, lint-free cloth to clean this appliance.
TROUBLESHOOTING
No heat or light: Check the wall socket by plugging in a working appliance. If the socket is functional, and the cord or plug of the heater is suspected to be faulty, have it checked by an electrician.
Light but no heat: Check that the Thermostat on the stove is set above the current room temperature. Alternatively, the thermal cut-off may have engaged – see thermal cut-off section.
DISPOSAL
Do not dispose of the device in normal domestic waste.
Dispose of the device over a registered waste disposal firm or through your
communal waste disposal facility.
Observe the currently valid regulations. In case of doubt, consult your waste
disposal facility.
WARRANTY
Dear Valued Customer,
Thank you very much for purchasing an MOA product.
We wish you to inform you that this product is covered by a warranty that
complies with all legal provisions concerning the existing warranty and
consumer rights in the country where the product was purchased.
Should you find any defect or malfunction of your MOA product, please contact
the appropriate Customer Care Center.
Sincerely yours,
The MOA Team
APPLIANCE DATA
| Item | Symbol | Value | Unit |
|---|
Heat output
| Nominal heat output | Phnom | 1.8 | KW |
|---|---|---|---|
| Minimal heat output | Pin | 0.9 | KW |
| Maximum continuous heat output | Pmax, c | 1.8 | KW |
Auxiliary electricity consumption
| At nominal heat output | ELmax | 0.012 | KW |
|---|---|---|---|
| At minimum heat output | ELmin | 0.012 | KW |
| In standby mode | ELsb | 0 | KW |
APPLIANCE DATA
Type of heat input, for electric storage local space heaters only (select
one)
Manual heat charge control, with integrated thermostat – Not applicable
Manual heat charge control with room and/or outdoor temperature feedback – Not
applicable
Electronic heat charge control with room and/or outdoor temperature feedback –
Not applicable
Fan-assisted heat output – Not applicable
Type of heat output/room temperature control (select one)
Single-stage heat output and no room temperature control – No
Two or more manual stages, no room temperature control – No
With mechanic thermostat room temperature control – Yes
With electronic room temperature control – No
Electronic room temperature control plus day timer – No
Electronic room temperature control plus week timer – No
Other control options (multiple selections possible)
Room temperature control, with presence detection – No
Room temperature control, with open window detection – No
With distance control option – No
With adaptive start control – No
With working time limitation – No
With black bulb sensor – No