IDEA FCS Series Professional Ceiling Speakers User Manual
- June 5, 2024
- iDea
Table of Contents
IDEA FCS Series Professional Ceiling Speakers
Technical Data | FCS4T
| Tweeter | 0.5” (13 mm) Silk soft dome |
|---|---|
| Woofer | 4” (100 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 98 Hz – 20 kHz |
| Power Handling RMS | 40 W program, 20 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 84 dB |
| Coverage | H:80° – V:70° |
| Crossover Frequency | 4 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 20 W, 10 W, 5 W, 2.5 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H x Diameter) | 167.5 x 204.2 mm (6.59” x 8.04”) |
| Weight | 2.17 kg (4.8 lb) |
| Cut out diameter | 175 mm (6.88”) |
| Material | ABS + iron |
Technical Data | FCS5T
| Tweeter | 0.75” (20 mm) Titanium dome |
|---|---|
| Woofer | 5” (125 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 85 Hz – 20 kHz |
| Power Handling RMS | 60 W program, 30 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 84 dB |
| Coverage | H:40° – V:30° |
| Crossover Frequency | 2.8 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 30 W, 15 W, 7.5 W, 3.25 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H x Diameter) | 234.5 x 238.5 mm (9.23” x 9.40”) |
| Weight | 2.8 kg (6.17 lb) |
| Cut out diameter | 206 mm (8.11”) |
| Material | ABS + iron |
Technical Data | FCS6T
| Tweeter | 1” (25 mm) Titanium dome |
|---|---|
| Woofer | 6.25” (165 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 65 Hz – 20 kHz |
| Power Handling RMS | 80 W program, 40 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 86 dB |
| Coverage | H:55° – V:45° |
| Crossover Frequency | 3.5 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 40 W, 20 W, 10 W, 5 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H x Diameter) | 238.8 x 264.8 mm (9.40” x 10.42”) |
| Weight | 3.3 kg (7.28 lb) |
| Cut out diameter | 226 mm (8.90”) |
| Material | ABS + iron |
Installation
STEP 1
Using a stud finder (available at low cost at most hardware stores) or another
accurate method, locate the center point between two joists and mark. Using
the template provided, trace a hole pattern on surface of ceiling.
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in
ceiling. Following trace pattern.
STEP 3
Run loudspeaker wire to sound source location. There are several methods you
can use to accomplish wiring, depending on the construction characteristics of
the room or house.You can add a professional touch to your installation by
using a speaker terminal plate at the source location. Leave sufficient amount
of wire at speaker location (8-10 inches / 20-25 cm) to complete connection.
STEP 4
Attach loudspeaker wires to speaker terminals, observe correct polarity, and
position speaker frame up into cutout. Be careful not to pinch wires in the
process.
STEP 5
Carefully tighten the four mounting screws. This will cause the mounting wings
to rotate our behind the mounting surface and secu-re the speaker in place.
STEP 6
After the speaker panel is secured tightly, test sound. When you are satisfied
the speaker is operational, then affix grill. As grill is designed for a snug
fit you’ll need to position one edge into slot first and press or squeeze
around perimeter of grill, while pushing leading edges into grill slot.
NECESSARY TOOLS
- Hammer
- Cross-headed screwdriver
- Paintbrush
- Keyhole saw
- Tape measure
- Pencil
Service
This unit has very sophisticated circuitry and should only be serviced by a fully trained technician. This is why each unit bears the following label: To prevent electric shock,do not remove covers. No user-serviceable parts inside. Refer servicing to a qualified technicians.
Worldwide service
Service may be obtained from your local authorized service center.To obtain
service, simply present your sales receipt as proof of purchase along with the
defective unit to an authorized service center.They will handle the necessary
paperwork and repair. Remember to transport your unit in the original factory
packaging.
- When sending a product to an authorized service center for service, be sure to fill out the service information form and include it inside your unit’s shipping pack. Do not send the service information form separately.
- To ensure the safe transportation of your unit to the authorized service center, ship it in an original factory-packing container.
- Do not ship the unit in any kind of rack. Ignoring this warning may result in extensive damage to the unit and the equipment rack. Accessories are not needed. Do not send the instruction manual, cables and any other hardware.
WEEE Mark
If you want to dispose of this product, do not mix with general household
waste.There are separate collection systems for used electronic products in
accordance with legislation under the WEEE Directive (Directive 2002/96/EC)
effective only within the Euro-pean Union.
Warranty
- All IDEA products are guaranteed against any manufacturing defect for a period of 5 years from date of purchase for acoustical parts and 2 years from date of purchase for electronic devices.
- The guarantee excludes damage from incorrect use of the product.
- Any guarantee repair, replacement and servicing must be exclusively done by the factory or any of authorized service centres.
- Do not open or intend to repair the product; otherwise servicing and replacement will not be applicable for guarantee repair.
- Return the damaged unit, at shipper’s risk and freight prepaid, to the nearest service centre with a copy of the purchase invoice in order to claim guarantee service or replacement.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>