moa TH20B Tower Heater Instruction Manual
- June 5, 2024
- moa
Table of Contents
moa TH20B Tower Heater
BEFORE USE
Before use, please read this manual carefully. Only connect the appliance to an earthed wall socket. This appliance is for household use only. When using electrical appliances, basic safety precautions should always be followed to avoid fires, electric shocks, burns, or other injuries and damage. Read these operating and safety instructions carefully.
IMPORTANT SAFEGUARDS
- Before using your new heater, please carefully read through the following instructions.
- KEEP THIS BOOKLET IN A SAFE PLACE SO THAT YOU MAY CONSULT IT LATER.
- After removing the packaging, make sure that the appliance is in good condition.
- The packaging materials may contain plastic, nails etc., which may be hazardous and therefore should not be left within the reach of children.
- Installation MUST be carried out by a qualified electrician.
- Avoid installation behind a door.
- Use only the voltage specified on the rating plate of the heater.
- Do not cover or restrict airflow to the inlet or exhaust grilles in any manner as the appliance may overheat and become a fire risk (for Fan Heaters).
- Do not cover grilles, block entry or exhaust of airflow by placing appliance against any surface. Keep all objects at least 1 metre from the front and sides of the appliance. With exception of appliances designed for wall-mounting, maintain a 1 metre gap from the rear of the unit as well.
WARNING: FIRE RISK EXISTS IF THE HEATER IS COVERED BY OR POSITIONED CLOSE TO CURTAINS OR OTHER COMBUSTIBLE MATERIALS
ASSEMBLY INSTRUCTIONS
-
Pass the power cord through the central gate and firmly clamp the left base with the right base, then coordinate the position of body with that position of the base , and fix the screws of the base with a screwdriver
-
Pass the power cord through the gap of the base.
-
Turn the heater ON by pressing the “main power” button at thee back side ot the heater. The unit will display the current Room temperature and blow the cold air.
-
Upon pressing the “+/” button,and “+/” button will light up,start set the suitable temperature(the highest temperature you can set until to 49,when the seted temperature is higher then room
-
temperature, the unit will start one heat setting,and at this time the “MODE” button will light up with WHITE color. It continue pressing the seted femperature will be even higher. Ihe unit will start
-
totally 2 heat settings. At this time the “MODE button will light up with RED colorOnce continue pressing+/ the setted temperature reached 49C, then the temperature restart from 10C.
. Press button”MODE one time pressing is in low heat setting and the “MODE”will light up with WHITE color. Iwo times pressing is in high heat setting and the “MODE will light up with -
WHITE color. When pressing this button tor third times, it will come back with only cool air blowing mode.
-
By pressing “2 arrows” button you can make the heater rotate
-
By pressing “alarm” button with the “alarm” light up,you can set the timer from 1-24 hours .
-
When you want to turn oft the heater, you can press “power bufton,thiIs fime the symbol fan blade will shining, and at the meaning fime,all the heafing will turn oft and only fan blowing,after blowing 30s,the heater will cut oft only with the “power” button become WHITE color.
Timer function
his tunction will work in any mode. I the timer function allows you to set the
length of operation fromI hour to 24 hours. Pressing the “alarm button
increase the length ot operation by 1 hour each times the button is
pressed.Once the fiber has been sef the timer will count down the hours in 1
hour by 1 hour, showing on the display the remaining operating fime until the
heater will turns itself ott. Pressing the timer button once more atter the
display reflects 24 hours will reset the heater to confinuously running.
OPERATION
- Before inserting the plug into an electrical outlet, make sure that the electrical supply in your area matches that on the rating label on the unit.
- Carefully remove the heater from the plastic bag and the carton.
- Place the heater on a firm level surface
- Setting the master button to “O”.plug the cord set into a 220- 240V-AC electrical outlet.Turnning the master button on, the heater will make a sound and light will
REMOTE CONTROL
-
Remote control, please use Lithium battery CR2025 3V.
-
The remote control power button is labeled as such
-
“ON/OFF”
-
“MODE”
-
“TIMER”
-
“OSCIL”
-
“CANCEL”
-
“UP”
-
“DOWN”
-
“FLAMES”
Main power button
COLD,WARM,HOT 3 setting for selection Setting timer from 1-24 hours
Oscillation function for heater Turn off the light of heater ,keep comfortable
sleep environment Setting temperature for increase Setting temperature for
decrease Flames display function
SAFETY TIP-OVER SWITCH
The appliance have safety tip-over switch for safe protected.Make the user away from fire and other damage.
OVERHEAT PROTECTION
This heater is protected with an overheat protection that switches oft the appliance automatically in case ot overheating. For example: due to the total or partial obstruction ot the vents. In this case, unplug the appliance, wait about 30 minutes for it to cool and remove the object which is obstructing the vents. Then switch it back on as described above. The appliance should now operate normally. It the problem persist, pledse contact Customer Service for assistance.
CLEANING & MAINTENANCE
Betore undertaking any cleaning or maintenance on the appliance, disconnect it from the power supPIY. For cleaning it is recommended to use a sot moist rag and neutral detergent. Do not use an abrasive cloth or devices which could affect the appearance ot the appliance. Check that the hot air outlet and the ventilation inlet are tree ot dust and dirt. During cleaning, be caretul not to touch the heating elements. lo open the filter on the back tor cleaning, press the top ot plastic net at back. In case of breakdown and/or poor functioning of the appliance, disconnect the appliance from the power supply and contact an authorised repairer.
DISPOSAL
Do not dispose of the device in normal domestic waste. Dispose of the device
over a registered waste disposal firm or through your communal waste disposal
facility. Observe the currently valid regulations. In case of doubt, consult
your waste disposal facility.
WARRANTY
Dear Valued Customer,
Thank you very much for purchasing an MOA product. We wish you to inform you
that this product is covered by a warranty that complies with all legal
provisions concerning existing warranty and consumer rights in the country
where the product was purchased. Should you find any defect or malfunction of
your MOA product, please contact the appropriate Customer Care Center.
Sincerely yours, The MOA Team