levenhuk WA60 Discovery Report Weather Station User Manual

: June 5, 2024
: levenhuk

Table of Contents

levenhuk WA60 Discovery Report Weather Station
Base station
Wind sensor
Rain gauge
Getting started
Weather forecast
Moon phase
Specifications
Care and maintenance
Battery safety instructions
Levenhuk Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

levenhuk WA60 Discovery Report Weather Station

levenhuk-WA60-Discovery-Report-Weather-Station-PRODUCT

Base station

levenhuk-WA60-Discovery-Report-Weather-Station-
FIG-1

Outdoor temperature and humidity
Wind speed
Rainfall
MODE button
Moon phase
SET button
Weather forecast
ALARM button
Wind direction
CHANNEL button
Atmospheric pressure
UP/+ button
DOWN/– button
Power input
Calendar
Time display
Indoor temperature and humidity
Wall mount holes
Battery compartment
Table stand (fold-out)
SNOOZE/LIGHT button

Wind sensor

levenhuk-WA60-Discovery-Report-Weather-Station-
FIG-2

Compass
Pole
Battery compartment
Wind direction sensor
Location of the temperature and
humidity sensor
Wind speed sensor
TX button
Channel switch

Rain gauge

levenhuk-WA60-Discovery-Report-Weather-Station-
FIG-3

Protective filter
Rain collector
Mounting feet
Tab to detach the rain collector
Tipping bucket
Battery compartment

Getting started

Base station

Connect the power cable to the device and connect the DC adapter to the AC power supply; or
Open the battery compartment cover (20) and insert 3 batteries according to the correct polarity. Close the cover.
Once the batteries are installed, the base station will search for the outdoor units for the first 5 minutes. After that, the base station can be manually set to receive. To do this, press the CHANNEL button for 2 seconds.
The effective range may differ depending on the unit’s position. Due to interference (various remote control devices, etc.), the maximum distance between the base unit and the outdoor unit may be significantly reduced. In such cases, we suggest moving the base unit and sensor a little. Sometimes it is enough to move one of these units just a few inches!

Wind sensor

Place the base station and the remote sensor within the effective transmission range. Open the battery compartment cover (3) and insert 4 batteries according to the correct polarity.
Set the channel switch (8) to the same channel selected on the base station, and then press the TX button. Check that the base station has received the signal. Press the TX button once more, if necessary. If the reception is successful, the base station display will show the temperature and humidity. Close the battery compartment cover.
Insert the aluminum pole (2) into the mounting base and fasten it with the screws (included). Screw the base to a wooden or stone wall using the supplied screws and plugs. Slide the upper part of the wind sensor onto the pole and fasten it with the screws.
The wind speed sensor, temperature, humidity, and wind direction part must be facing south. Orientate the outdoor wind unit using the compass to ensure the correct wind direction.

Rain gauge

Open the battery compartment cover (6) and insert 2 batteries according to the correct polarity. Close the cover and secure it with the screws.
Fasten the rain gauge by inserting the screws through the mounting feet (3). To replace the batteries, first unscrew the rain gauge.

Time setting
Press the MODE button. Hold the SET button for 3 seconds. The digits that are to be set are flashing. Press UP or DOWN to change the value, and then press SET to continue. The setting order: Time zone > Day Saving Time > Year > Month-Day or Day-Month > Month > 12/24h > Hour > Minutes > Seconds.

Alarm setting

To activate alarm 1 and/or alarm 2, press the ALARM button.
To set alarm 1 and alarm 2, first press the MODE button 2 times. Hold the SET button for 3 seconds. The digits that are to be set are flashing. Press UP or DOWN to change the value, and then press the SET button to continue.
The setting order: Alarm 1 hours > Alarm 1 minutes > Alarm 2 hours > Alarm 2 minutes.
When the alarm rings, press SNOOZE/LIGHT to activate the snooze function. The alarm will sound again in 5 minutes.
Press any button to silence the alarm until the set alarm time is reached again.

Atmospheric pressure height setting
Press the MODE button 3 times. Hold the SET button for 3 seconds. The digits that are to be set are flashing. Press
UP or DOWN to insert the desired height.

Temperature alert setting

Press the MODE button 4 times. Hold the SET button for 3 seconds. The digits that are to be set are flashing. Press
UP or DOWN to change the value. Press the SET button to continue.
The setting order: Low outdoor temperature alert > Low outdoor temperature alert on/off > High outdoor
temperature alert > High outdoor temperature alert on/off > Low indoor temperature alert > Low indoor
temperature alert on/off > High indoor temperature alert > High indoor temperature alert on/off.

Units of measurement

Press the SET button to switch between °C and °F.
Press the MODE button 3 times. Hold the SET button for 3 seconds. Press the SET button again to enter the setting mode. The digits that are to be set are flashing. Press UP or DOWN to switch between inHg, hPa, and mmHg.
Press the MODE button 5 times. Hold the SET button for 3 seconds. The digits that are to be set are flashing. Press UP or DOWN to switch between mm and inches.
Press the MODE button 6 times. Hold the SET button for 3 seconds. The digits that are to be set are flashing. Press UP or DOWN to switch between km/h and mph.

Weather forecast

levenhuk-WA60-Discovery-Report-Weather-Station-
FIG-4

History record

Press the UP button to display the MAX./MIN. wind speed, temperature, and humidity. Hold the UP button to clear the history records.
Press the DOWN button to display the rainfall history. The display order: today > past hour > yesterday > this week. Hold the DOWN button to clear the history records.

Moon phase

levenhuk-WA60-Discovery-Report-Weather-Station-
FIG-5

The moon phase display is linked to the date, year, and time. The stars are displayed between 6 pm and 6 am.

Specifications

levenhuk-WA60-Discovery-Report-Weather-Station-
FIG-6

The manufacturer reserves the right to make changes to the product range and specifications without prior notice.

Care and maintenance

Take the necessary precautions when using the device with children or others who have not read or who do not fully understand these instructions.
Do not try to disassemble the device on your own for any reason. For repairs and cleaning of any kind, please contact your local specialized service center.
Protect the device from sudden impact and excessive mechanical force.
Store the device in a dry, cool place away from hazardous acids and other chemicals, away from heaters, open fire, and other sources of high temperatures.
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
Only use accessories and spare parts for this device that comply with the technical specifications.
Check this device and its cables and connections for any possible damage before use.
Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
If a part of the device or battery is swallowed, seek medical attention immediately.
Children should use the device under adult supervision only.

Battery safety instructions

Always purchase the correct size and grade of battery most suitable for the intended use. Always replace the whole set of batteries at one time; taking care not to mix old and new ones, or batteries of different types. Clean the battery contacts and also those of the device prior to battery installation. Make sure the batteries are installed correctly with regard to polarity (+ and –). Remove batteries from equipment that is not to be used for an extended period of time. Remove used batteries promptly. Never short-circuit batteries as this may lead to high temperatures, leakage, or explosion. Never heat batteries in order to revive them. Do not disassemble batteries. Remember to switch off devices after use. Keep batteries out of the reach of children, to avoid risk of ingestion, suffocation, or poisoning. Utilize used batteries as prescribed by your country’s laws.

Levenhuk Warranty

Levenhuk products, except for their accessories, carry a 2-year warranty against defects in materials and workmanship. All Levenhuk accessories are warranted to be free of defects in materials and workmanship for six months from the purchase date. The warranty entitles you to the free repair or replacement of the Levenhuk product in any country where a Levenhuk office is located if all the warranty conditions are met. For further details, please visit: www.levenhuk.com/warranty If warranty problems arise or if you need assistance in using your product, please contact the local Levenhuk branch.