7Pandas H0594504 Stella Motion Sensor Outdoor Exterior Wall Sconce Instruction Manual

7Pandas H0594504 Stella Motion Sensor Outdoor Exterior Wall Sconce

Product Information

Model: H0594504

WARNING: To avoid the risk of electrical shock, be sure to shut off power while installing or servicing this fixture.

Notes:

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.

To work properly, you should install this fixture away from any jets of air conditions or strong airflow.

Components:

• Machine Screw
• Ground Wire
• Black Wire
• GND
• Caulk
• Outlet Box
• Negative Wire
• Live Wire
• White Wire
• Rubber Washers
• Decorative Nuts
• Socket
• Lampshade
• Stationary Ring
• Bulb (Not included)

Product Usage Instructions

1. Consult local electrical codes and wiring requirements before installation.
2. Shut off power before installing or servicing the fixture.
3. Install the fixture away from jets of air conditions or strong airflow.
4. Align the shade onto the socket cup and secure it with the socket ring.
5. Caulk completely around where the back plate meets with the wall surface using silicone caulking compound to prevent water seepage into the outlet box.
6. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to ensure maximum sensitivity of the motion sensor.
7. Install the fixture at least 6 feet above the ground for optimal performance.
8. The fixture provides a detection distance of up to 40 feet at 77 degrees Fahrenheit when installed at a height of 6 feet above the ground.
9. The sensor detects across a detection range of 220 degrees.
10. The sensor is more sensitive to motion across its detection path than motion directly towards it.
11. Avoid mounting the fixture near heat sources like air conditioners, vents, furnaces, or in a direction facing reflecting objects or other light sources to reduce possible nuisances.

Troubleshooting

Turn on the switch or circuit breaker. Check wire
connections.
The light doesn’t work in Auto mode| Wall switch or circuit breaker is off| Turn on the switch or circuit breaker.
The light bulb may be dead| Test the light bulb in a known working light fixture| Test the light bulb in a known working light fixture.
In Auto mode, the lighting fixture does not turn on when there
is motion| Light bulb is loose. Incorrect or loose wire connections. Too
much sunlight is shining into the Dusk-to-Dawn sensor in the early
evening.| Tighten the light bulb in the socket. Check wire connections.
Relocate the fixture away from a western facing wall.
In Auto mode, the lighting fixture does not turn on when there
is motion| Too much light is shining onto the Dusk-to-Dawn sensor due to
another light source, such as a street lamp or other light
fixture.| Eliminate or turn off other light sources, block other light
sources from shining onto the Dusk-to-Dawn sensor, or relocate the
fixture.

ASSEMBLY AND INSTALLATION INSTRUCTIONS

Model: H0594504

WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE

NOTES:

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.

To work properly.you should install this fixture NOT confront any jets of air conditions or strong airflow

1. Attach the mounting plate to the outlet box by using two mounting screws.

2. Pull out the wires and grounding wire from the outlet box. Make wire connections using the wire nuts, as follow:

   • Connect the hot wire(usually black insulation)from the fixture to the black wire from the power source.
   • Connect the neutral wire(usually white insulation)from the fixture to the white wire from the power source.
   • Attach the fixture grounding wire(usually green insulation or bare wire)to the mounting strap with the green grounding screw.Then connect it to the house grounding wire with the wire nut.
     Carefully put the wires back into the outlet box.

3. Attach the back plate to the mounting plate by inserting the screws.then secure it with two nuts.

4. Align the shade onto socket cup , and secure with socket ring

5. Install light bulbs (60W A 19). (Bulbs not included, Please do not exceed the maximum capacity recommended on the socket.

CAUTION: With silicone caulking compound, caulk completely around where the back plate meets with the wall surface to prevent water from seeping into the outlet box.

Tum on the power at fuse or circuit box.

Function and Operation

MODES OF OPERATION

NOTE:

1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to assure maximum sensitivity.

2. For best performance, install fixture at least 6 feet above
   The ground. At such a height, the lantern will provide a detection distance of up to 40 feet at 77 degrees Fahrenheit.(See Fig.2)

3. The sensor detects across a detection range of 220 degrees.(See Fig.3)

4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.4)

5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflecting object or other light source.

Troubleshooting

connections.

In Auto mode, the lighting fixture does not turn on when there is motion

| Wall switch or circuit breaker is off| Turn on a switch or circuit breaker.
Light bulb may be dead.| Test the light bulb in a known working light fixture
Light bulb is loose.| Tighten the light bulb in the socket.
Incorrect or loose wire connections.| Check wire connections.
Too much sunlight is shining into the

Dusk-to-Dawn sensor in the early evening.

| Relocate fixture away from a western facing wall.
Too much light is shining onto the

Dusk-to-Dawn sensor due to another light source, such as a street lamp or other light fixture.

| Eliminate or turn off other light source, block other light source from shining onto Dusk-to-Dawn    sensor, or relocate fixture.
In Auto mode, the lighting fixture stays on at 100% brightness continuously.| False triggering caused by a heat source, such as a heater or dryer vent, or air conditioning vent ,or heated swimming pool.| Eliminate heat source or relocate fixture
The lighting fixture comes on at 100% brightness for no apparent reason| alse triggering caused by a heat source, such as a heater or dryer vent,or air conditioning vent ,or heated swimming pool.| Eliminate heat source or relocate fixture
The lighting fixture comes on during the daytime or too early in the evening| The fixture may be installed in a shaded area, such as under a porch or eave, preventing daylight from shining onto the photocell sensor.| Relocate the fixture
The LED bulb or fluorescent bulb flickers when the lighting fixture is dimmed down to the stand-by dimming level .| Non-dimmable LED bulb or fluorescent bulb is used on the lighting fixture.| Replace dimmable LED bulb or fluorescent bulb, or incandescent bulb
In Manual override, the light stays on after dawn| the ambient light level is too low| Relocate the fixture

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>