infobit iCam P10 HD PTZ Conference Camera User Manual

infobit iCam P10 HD PTZ Conference CameraNote

• Electric Safety
  Installation and operation must accord with electric safety standard.

• Use caution to transport
  Avoid stress, vibration or soakage in transport, storage and installation.

• Polarity of power supply
  The power supply of this product is +12V, the max electrical current is 2A. Polarity of the power supply plug drawing shows as below.

• Installation Precautions
  Do not grasp the camera lens when carrying it. Don’t touch camera lens by hand. Mechanical damage may be caused by doing so.
  Do not use in corrosive liquid, gas or solid environment to avoid any cover (plastic material) damage. Make sure there is no obstacle within rotation range.
  Please never power on before installation is completed.

• Do not dismantle the camera
  We are not responsible for any unauthorized modification or dismantling.

Specific frequencies of the electromagnetic field may affect the image of the camera!

Packing List

When you unpack, check that all the supplied accessories are included:

Quick Start

1. Please check connections are correct before starting.
2. Connect the power adapter to the power connector on the rear panel of the camera. The power indicator on the front panel of the camera is on.
3. After the camera is power on, it starts to initialize, right up to the limit position, and then both horizontal and vertical go to the middle position, the motor stops running, and the initialization is completed.
   (Note: If preset 0 is saved, PTZ will be move to preset 0)

About Product

1. Features

2. New Appearance
   Supports worm and worm drive design, new appearance, mini-style, two-color optional.

3. USB 3.0
   Supports UVC protocol, compatible with USB 2.0 and USB 3.0, USB 3.0 supports up to 1920x1080p/60 output, and USB 2.0 supports up to 960x540p/60 output. When the camcorder is connected to the PC through the USB for the first time, the PC will automatically install the UVC-related drivers.

4. Built-in Microphone
   Built-in microphone, pick up distance up to six meters, high sensitivity, low noise floor.

5. 1080P Full HD
   With the new generation of Panasonic 1/2.7 inch, 2.07 million effective pixels of high-quality HD CMOS sensors, you can achieve high-quality images with a maximum resolution of 1920×1080.

6. High Frame Rate
   1080P output frame rate up to 60fps.
   72.5° Wide-angle lens + 16x Digital Zoom With a 72.5° high quality super-lens lens, the optical zoom can be up to 12 times and supports 16x digital zoom (optional).

7. Low illumination
   The application of 2D and 3D noise reduction algorithm greatly reduces the image noise. Even under the condition of ultra-low illumination, it still keeps the picture clean and clear, and the SNR of image is as high as 55dB.

8. Remote Control
   Through the RS232 and RS485 serial ports, the camera can be controlled remotely.

9. Product Specification**
   Model| iCam P10
   ---|---
   Name| PTZ Conference Camera
   Camera**

   ---

Signal System

| 1080p/60 (optional), 1080p/50 (optional), 1080p/30, 1080p/25,

720p/60, 720p/50,

720p/30, 720p/25

Sensor

| 1/2.7 inch, CMOS, Effective     pixels:     2.07 million
Scanning Mode| Progressive
Lens| 12x, f3.5mm ~ 42.3mm, F1.8 ~ F2.8
Digital Zoom| 16x (optional)
Minimum Illumination| 0.5Lux @ (F1.8, AGC ON)
Shutter| 1/30s ~ 1/10000s
White Balance| Auto, Indoor, Outdoor, One Push, Manual, VAR
Backlight Compensation| Support
Digital Noise

Reduction

| 2D, 3D digital noise

reduction

Signal Noise Ratio| ≥55dB
Horizontal Angle of View| 72.5° ~ 6.9°
Vertical Angle of

View

| 44.8° ~ 3.9°
Horizontal Rotation Range| ±170°
Vertical Rotation Range| -30° ~ +30°
---|---
Pan Speed Range| 1.7° ~ 100°/s
Tilt Speed Range| 1.7° ~ 69.9°/s
H & V Flip| Support
Image Freeze| Support
Number of

Preset

| 255
Preset Accuracy| 0.1°
USB Feature
Operating System| Windows XP/Vista/7/8/10, Mac OS X, Linux
Color space/ Compression| YUV 4:2:2/H.264/MJPEG
Video Format| USB3.0: 1080p/60

(optional), 1080p/50 (optional), 1080p/30, 1080p/25, 720p/60,

720p/50, 720p/30, 720p/25 USB2.0: 1080p/30, 1080p/25, 1080p/15,

1080p/10, 720p/30,

720p/25, 960x540p/30,

960x540p/25,

640x360p/60,

640x360p/50

USB Audio| Support
USB Video Communication

Protocol

| ****

UVC 1.1, UVC 1.5

UVC PTZ

Control

| Support
Input/Output Interface
USB Interface| 1 x USB3.0: Type B female

jack

Audio Interface| 1-ch: 3.5mm Audio Interface, Line In

Communication Interface

| 1 x RS232 In: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA / Pelco-D

/ Pelco-P

1 x RS232 Out: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA network use only

Communication Interface

| 1 x RS485: Share with RS232 Out, Max Distance: 1200m, Protocol: VISCA/Pelco-D/Pelco-P
---|---
Power Jack| JEITA type (DC IN 12V)
Physical Parameter
Input Voltage| DC 12V
Current

Consumption

| 1.0A (Max)
Operating Temperature| -10°C ~ 40°C
Storage Temperature| -40°C ~ 60°C
Power

Consumption

| 12W (Max)
MTBF| ＞30000h
Size| 128 x118 x158mm
Net Weight| 0.91Kg
3. Interfaces and Buttons
Item| Name
---|---
1| USB 3.0 Interface
2| LINE IN Interface
3| RS232 IN Interface
4| RS232 OUT Interface
5| DC 12V Power Interface
4. Dimension 5. RS-232 Interface Remote Control
Key Description

1. Standby Key
Press this button to enter standby mode. Press it again to enter normal mode.

Note: Power consumption in standby mode is

approximately half of the normal mode

2. Number Key
To set preset or call preset
* _3. Key_
Used with other buttons.
4. Preset Key**
Set preset: Store a preset position. [SET PRESET] + Numeric button (0-9): Setting

a corresponding numeric key preset position.

5. HOME Key Confirm menu, enter the submenu or the PTZ will back to the middle position after pressed it

6. Return Key Return back the last level menu

7. Zoom KeySlow Zoom: Zoom In [+] or Zoom Out [-] slowly Fast Zoom: Zoom In [+] or Zoom Out [-] fast

8. Left/Right Setting Key Press with 1 buttons and 2 buttons setting the direction of the Pan-Tilt.

  * Simultaneously press L/R Set +1[STD]: set the Pan-Tilt turn the same direction as the L/R Set.
  * Simultaneously press L/R Set +2[REV]: set the Pan-Tilt turn the opposite direction as the L/R Set.

9. Focus Key

Used for focus adjustment.
Press [AUTO] adjust the focuses on the center of the object automatically. To adjust the focus manually.
Press [MANUAL] adjust the focus on the center of the object manual.
MANUAL button, and adjust it with [Far] (Focus on far object) and [NEAR] (Focus on near object).

10. Selection Key

Press the button corresponding to the camera you want to operate with the remote controller.

11. #Key

Used with other buttons.

12. IR Remote Control Key

[]+[＃]+[F1]: Address 1 []+[＃]+[F2]: Address 2 []+[＃]+[F3]: Address 3 []+[＃]+[F4]: Address 4

13. Reset Key

Clear preset: Erase a preset position.
[CLEAR PRESET] + Numeric button (0-9) Or: [*]+[#]+[CLEAR PRESET]: Erase all the preset individually.

14. PTZ Control Key

Press arrow buttons to perform panning and tilting. Press [HOME] button to face the camera back to front.

15. Menu Key

MENU: enter or exit OSD MENU.  iCam P10 PTZ Conference Camera

16. Backlight Key

BLC ON/OFF: Press this button to enable the backlight compensation. Press it again to disable the backlight compensation.
NOTE:

  * Effective only in auto exposure mode.
  * If a light behind the subject, the subject will become dark. In this case, press the backlight ON/OFF button. To cancel this function, press backlight ON/OFF button.

17. PTZ Reset Key

Preset Pan/Tilt self-test.

18. Image Freezing Function

Manually freeze: Open the freezing function after press the remote control [F4], display “Freeze” on the left upper corner character, after five seconds display disappear automatically. If you want to cancel the freeze, press [F4] key and then can return to normal, display “Unfreeze” on the left upper corner, after five seconds display will disappear automatically.
Recalling the Preset image Freeze: By the OSD Menu “Image Freeze” to set recalling the preset image freeze function. After the function is opened, the screen will stay in before Recalling the Preset when Recalling the Preset, the screen can be switched to the preset position screen until the camera points to the preset position.

19. Shortcut Set

[]+[＃]+[1]: OSD menu default English []+[＃]+[3]: OSD menu default Chinese []+[＃]+[6]: Quickly recover the default []+[＃]+[8]: Look the camera version [*]+[＃]+[9]: Quickly set up inversion
6. RS-232 Interface**
No.| Function**
---|---
1| DTR
2| DSR
3| TXD
4| GND
5| RXD
6| GND
7| IR OUT
8| NC

The correspondence between the camera and Windows DB-9 pin: The correspondence between the camera and the Mini DIN pin:

7. VISCA Network

8. Serial Communication Control

9. RS232 Communication Control
   The camera is controlled via RS232. The RS232 serial port parameters are as follows: Baud rate: 2400/4800/9600/38400;

10. Starting Position: 1 bit

11. Data bit: 8 bits

12. Stop bit: 1 bit

13. Check digit: None

14. List of protocols (omitted)
    The serial port of the camera follows the VISCA/Pelco-D/Pelco-P standard protocol. If secondary development is required, the camera can be controlled according to the standard protocol.
    For a detailed list of VISCA/Pelco-D/Pelco-P protocols, contact the manufacturer.

GUI Settings

1. MENU
   Press [MENU] button to display the main menu on the normal screen, using arrow button to move the cursor to the item to be set. Press the [HOME] button to enter the corresponding sub-menu.| MENU
   ---|---
   | Exposure
   | Color
   | Image
   | P/T/Z
   | Noise Reduction
   | Audio
   | Setup
   | Communication Setup
   | Restore Default
   | [Home] Enter
   | [Menu] Exit

2. EXPOSURE
   Move the main menu cursor to [EXPOSURE], and press [HOME] key enter the exposure page, as shown in the following figure.| EXPOSURE|
   ---|---|---
   | Mode| Auto
   | ExpCompMode| Off
   | Backlight| Off
   | Gain Limit| 3
   | Anti-Flicker| 50Hz
   | Meter| Average
   | DRC| 2
   | Select Item|
   | Change Value
   | [Menu] Back|

3. Mode: Exposure mode, optional items: Auto, Manual, SAE, AAE, Bright.

4. ExpCompMode: Exposure compensation mode, optional items: On, Off (Effective only in Automode).

5. ExpComp: Exposure compensation value, optional items: -7 ~ 7 (Effective only in ExpCompMode item to On).

6. Backlight: Set the backlight compensation, optional items: On, Off (Effective only in Auto mode).

7. Bright: Intensity control, optional items: 00 ~ 17 (Effective only in Bright mode).

8. Gain Limit: Maximum gain limit, optional items: 0 ~ 15 (Effective only in Auto, AAE, Bright mode).

9. Anti-Flicker: Anti-flicker, optional items:

10. Off, 50Hz, 60Hz (Effective only in Auto, Bright mode).

11. Meter: optional items: Average, Center, Smart, Top.

12. Iris: Aperture value, optional items: F1.8, F2.0, F2.4, F2.8, F3.4, F4.0, F4.8, F5.6, F6.8, F8.0, F9.6, F11.0, Close (Effective only in Manual, AAE mode).

13. Shutt: Shutter value, optional items: 1/30, 1/60, 1/90, 1/100, 1/125, 1/180, 1/250, 1/350, 1/500, 1/725, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000, 1/6000, 1/10000 (Effective only in Manual, SAE mode).

14. DRC: DRC strength, optional items: 0 ~ 8.

15. COLOR
    Move the main menu cursor to [COLOR], and press [HOME] key enter the color page, as shown in the following figure.| COLOR|
    ---|---|---
    | WB Mode| Auto
    | Saturation| 100%
    | Hue| 7
    | AWB Sens| Middle
    | Select Item
    | Change Value
    | [Menu] Back|

16. WB-Mode: White balance mode, optional items: Auto, Indoor, Outdoor, One Push, Manual, VAR.

17. RG: Red gain, optional items: 0 ~ 255 (Effective only in Manual mode).

18. B G: Blue gain, optional items: 0 ~ 255 (Effective only in Manual mode).

19. Color Temp: Optional items: 2500K ~ 8000K (Effective only in VAR mode).

20. RG Tuning: Red gain fine-tuning, optional items: -10 ~ +10 (Effective only in AWB sens is Low).

21. BG Tuning: Blue gain fine-tuning, optional items: -10 ~ +10 (Effective only in AWB sens is Low).

22. Saturation: Optional items: 60% ~ 200%. Hue: Chroma adjustment, optional items: 0 ~ 14.

23. AWB Sens: The white balance sensitivity, optional items: Low, Middle, High.

24. IMAGE
    Move the main menu cursor to [IMAGE], and press [HOME] key enter the image page, as shown in the following figure.| IMAGE|
    ---|---|---
    | Luminance| 7
    | Contrast| 10
    | Sharpness| 3
    | Flip-H| Off
    | Flip-V| Off
    | B&W Mode| Off
    | Gamma| Default
    | Style| Clarity
    | Select Item
    | Change Value
    | [Menu] Back|

25. Luminance: Brightness adjustment, optional items: 0 ~ 14.

26. Contrast: Contrast adjustment, optional items: 0 ~ 14.

27. Sharpness: Sharpness adjustment, optional items: Auto, 0 ~ 15.

28. Flip-H: Image flipped horizontally, optional items: On, Off.

29. Flip-V: Image Flip Vertical, optional items: On, Off.

30. B &W Mode: Optional items: On, Off.

31. Gamma: Optional items: Default, 0.45, 0.5, 0.56, 0.63.

32. Style: Optional items: Norm, Clarity (LED), Clarity, Bright, Soft, 5S, QS.

33. P/T/Z
    Move the main menu cursor to [P/T/Z], and press [HOME] key enter the P/T/Z page, as shown in the following figure.

34. SpeedByZoom: The depth of field scale switch, optional items: On, Off.

35. AF-Zone: Interested in focusing area, optional items: Top, Center, Bottom.

36. AF-Sense: Automatic focusing sensitivity options, optional items: Low, Medium, High. Display Info: Optional items: On, Off.

37. Image Freeze: Optional items: On, Off.

38. Digital Zoom: Optional items: Off, 2x, 4x, 8x, 16x.

39. Call Preset Speed: Optional items: 1 ~ 24. Pre Zoom Speed: Optional items: 0 ~ 7.

40. Voice Track: Optional items: On, Off.

41. NOISE REDUCTION
    Move the main menu cursor to [NOISE REDUCTION], and press [HOME] key enter the noise reduction page, as shown in the following figure. NOISE REDUCTION

    | NR2D-Level| 3
    | NR3D-Level| 3
    |  Select Item
    |  Change Value
    | [Menu] Back|

42. NR2D Level: 2D noise reduction, optional items: Off, Auto, 1 ~ 5.

43. NR3D Level: 3D noise reduction, optional items: Off, 1 ~ 8.

44. AUDIO
    Move the main menu cursor to [AUDIO], and press [HOME] key enter the audio page, as shown in the following figure.

45. Audio Source: Optional items: MIC, LINE. NR-Level: Optional items: LOW, MID, HIGH.

46. SETUP
    Move the main menu cursor to [SETUP], and press [HOME] key enter the setup page, as shown in the following figure.| SETUP|
    ---|---|---
    | Language| EN
    | USB Mode| BULK
    | ID CONF| 1
    | OSD Flip| Off
    | Select Item
    | Change Value
    | [Home] Enter|
    | [Menu] Back|

47. Language: Optional items: EN, Chinese, Russian.

48. USB Mode: Optional items: BULK, ISOC.

49. ID CONF: Optional items: 1, 2.

50. OSD Flip: Optional items: On, Off.

51. COMMUNICATION SETUP
    Move the main menu cursor to [COMMUNICATION SETUP], and press [HOME] key enter the communication setup page, as shown in the following figure.

52. Protocol: Control protocol type, optional items: AUTO, VISCA, PELCO-D, PELCO-P.

53. V_Address: Optional items: 1 ~ 7.

54. P_D_Address: Optional items: 0 ~ 254.  (Effective only in PELCO-D protocol). P_P_Address: Optional items: 0 ~ 31. (Effective only in PELCO-P protocol).

55. V_AddrFix: If you can change through the serial port of infrared switch, optional items: On, Off (When set to On, useless in 88 30 01 FF Command).

56. Net Mode: Set the serial port control networking, optional items: Serial, Paral. Baudrate: Serial port baud rate, optional items: 2400, 4800, 9600, 38400.

57. RESTORE DEFAULT
    Move the main menu cursor to [RESTORE DEFAULT], and press [HOME] key enter the restore default page, as shown in the following figure. NOISE REDUCTION

    | NR2D-Level| 3
    | NR3D-Level| 3
    |  Select Item
    |  Change Value
    | [Menu] Back|

58. Restore: Confirm restore factory settings, optional items: Yes, No.
    Note: Press [HOME] button to confirm, all parameter restore default, include IR Remote address and VISICA address.

Maintenance and Troubleshooting

Camera Maintains

• If camera will not be used for a long time, please turn off the power switch, disconnect AC power cord of AC adaptor to the outlet.
• Use soft cloth or tissue to clean the camera cover.
• Please use the soft dry cloth to clean the lens. If the camera is very dirty, clean it with diluted neuter detergent. Do not use any type of solvents, which may damages the surface.

Unqualified Application

• No shooting extreme bright object for a long period of time, such as sunlight, light sources, etc.
• No operating in unstable lighting conditions, otherwise image will be flickering.
• No operating close to powerful electromagnetic radiation, such as TV or radio transmitters, etc.

Troubleshooting Image

1. The monitor shows no image

2.  Check that the camera power supply is connected, the voltage is normal, and the power indicator light is always on.

3. Turn off the power switch to check whether the camera is self-testing.

4. Check the cable of video platform and TV whether correct connection.

5. Sometimes without the image
   Check the cable of video platform and TV whether correct connection.

6. Image have jitter when the camera lens at max multiple.

7. Check whether the camera installed position be stabled.

8. Check whether have vibrating machinery or object near the camera.

Control

1. Remote control can not control
2. Check and replace the new battery for the remote controller.
3. Check whether the camera working mode is correct.
4. Series port can not control
5. Check whether the camera protocol, address such is the same.
6. Check whether the control line is connected well.

Contact US

• United Kingdom INFOBIT AV LTD. info@infobitav.com Fifth Floor 3 Gower Street London WC1E 6HA
• Singapore INFOBIT AV PTE. LTD. info@infobitav.com 3 Shenton Way, Shenton House #09-02, Singapore 068805
• China INFOBIT AV LTD. info@infobitav.com Chaoyang, Beijing China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>