COMMAX CDV-70KPT Tilt Color Video Door Phone User Manual

COMMAX CDV-70KPT Tilt Color Video Door Phone

Warnings and caution

Please follow the things described below in order to prevent any danger or property damage

Warning It may cause a serious damage or injury if violated.

Caution It may cause a minor damage or injury if violated.

Warning & Caution

Cleaning & Use

Please don’t disassemble, repair or rebuild this product arbitrarily (please contact the service center if a repair is needed.

• It may cause an electric shock or fire.

If an abnormal sound, burning smell or smoke is coming out of the product, please plug out the power cable and contact a service center.

• It may cause an electric shock or fire.

Please don’t insert any metallic or burnable materials into the ventilation hole.

• It may cause an electric shock or fire.

When cleaning the product, please rub it with a soft and dry cloth after plugging out the power cable. (Please don’t use any chemical products such as wax, benzene, alcohol or cleanser.)

Power & Installation

Please don’t use several products at the same time on one power socket.

• It may cause a fire due to an abnormal overheating

Please don’t bend the power cable excessively or it may cause an electric shock.

• fire when using a damaged power cable.

Please don’t handle the power cable with a wet hand.

• It may cause an electric shock.
  

Please plug out the power cable from the socket when not using it for a long period of time.

• It may shorten the product lifespan or cause a fire.
  

Please don’t install the product in the place where there is much oil, smoke or humidity.

• It may cause an electric shock or fire.
  

Please don’t install the product with the lightening and thunder.

• It may cause an electric shock or fire.

Please don’t use and connect this product with other products with different rated voltage

• It may cause a disorder or fire.
  

When installing the productthat generates heat, pleaseinstall the product away from the wall (10cm) for the ventilation.

• It may cause a fire due tothe increased internal temperature.

Parts Names

Package Contents

Wiring and Connection Instructions

• Polarity of the camera connector

1. Red: Talk (Audio)
2. Blue: GND
3. Yellow: Power (+12V) 4
4. White: Video
   

• Polarity of interphone connector

1. Red: Talk (Audio)
2. Blue: GND
3. Yellow: Power (+14V)
4. White: Call signal

Each device should be connected by If you use UTP CABLE[CAT.5] for separated cables. CAMERA1and CAMERA2, 2 lines of UTP cable are required.

Installation

Note
① Avoid the range of direct sunlight
② Recommended height is pertinent from 1450 ~ 1500mm
③ Avoid the installation near magnetic activity, humid temperatures and gas

DOOR CAMERA & INTERPHONE Wiring

If you use UTP CABLE[CAT.5], connect the rest 4 lines to GND after connecting 4 lines between monitor and interphone.

Operation

*  Caution : Do not hold the handset at your ear when you press hook switch to switch call.

**Calling of visitor

**

Communication with the optional Interphone

Dialog between the interphone and camera is possible only when the visitor’s image is visible on the monitor screen.

Monitoring : function to see the image of visitor in the entrance

On stand-by mode – status of putting handset down ) Operation
– By pressing the Monitor button repeatedly, the monitor will work as following in order. Camera 1 → Camera 2 → OFF → Camera 1 → .
(One talking mode – status of putting handset up) Operation
– By pressing the Monitor button repeatedly, the monitor will work as following in order. Camera 1 → Camera 2 → Camera 1 → Camera 2 → .

Adjust the volume

* Caution
When the call volume control switch is clicked for call volume adjustment, call sound will be heard from the handset 1 time for a user to check the sound.
Please make sure that handset is in position, when the call volume function is being used
– When call volume control switch is clicked, it will operate in order as follows.
– (Stand by mode – In position)
– CHIME-VOL0 → CHIME-VOL1 → CHIME-VOL2 → CHIME-VOL3 → CHIME- VOL0

CAMERA TILT FUNCTION

Users can adjust the image focus to see the place that they want.
Functions are only available with pan tilt cameras.

Display setting “ZOOM, 4:3, 16:9” SCREEN MODE is not available when it is connected to pan tilt cameras.
(Click the front key buttons to use pan tilt function during the monitoring or talk.)

Move left : LEFT BUTTON         * Move down : DOWN BUTTON

• Move up : UP BUTTON           * Move right : RIGHT BUTTON

– Enlarge or reduce screen size by using UP/DOWN buttons on the side during the monitoring or talk.
UP : Enlarge screen size gradationally (ZOOM – IN)
DOWN : Reduce screen size gradationally (ZOOM – OUT)
* Caution
When the unit is restarted, the zoom mode will be innitialized.

Settings

• Products settings need the following 4 buttons on the right of product.
• Move left : LEFT BUTTON           * Move down : DOWN BUTTON
• Move up : UP BUTTON                * Move right : RIGHT BUTTON

Screen setting (Brightness/Contrast/Color adjustment function)

Press the Menu button and access to DOOR VIDEO SET and enter the setting menu
by pressing SELECT button.

1. BRIGHTNESS : Adjusting Brightness of Screen

2. CONTRAST : Adjusting Contrast of Screen

3. COLOR : Adjusting Color of Screen
   ※ How to adjust
   ① Move to Menu you want to adjust with navigation button on the list of DOOR
   VIDEO SET
   ② Press SELECT button to choose an icon.
   ③ Adjust the set value with navigation button
   ④ To complete the set, press SELECT button.

4. RESET : Initializing
   ※ How to reset.
   ① Move to RESET menu in DOOR VIDEO SET menu
   ② Press SELECT to enter the menu.
   ③ Select YES with navigation button
   ④ Press SELECT button.

5. EXIT : Go back to setting mode

UTILITY(additional function)

Press the Menu button and access to Utility SET and enter the menu by pressing SELECT button.

1. CHIME-BELL VOLUME : setting volume sound .
   ① Move to CHIME-BELL VOLUME icon with navigation button in UTILITY Menu.
   ② Press SELECT to enter the menu.
   ③ Select the volume sound or not with navigation button.
   ④ To complete the set, press SELECT button.

2. EXIT : Go back to Setting menu

INFORMATION (The function to check Model name & Version)

In order to check the product information, press menu button and move to
INFORMATION menu with navigation button.

1. MODEL : You can check the model name.
2. VERSION : You can check the model version.
3. VIDEO : You can check the video transmission formats(NTSC / PAL)
4. SOURCE : You can check the position of camera(DOOR1 / DOOR2) which is shown on the screen for now

EXIT(Finish setting menu)

RESET : Initializing

Keep pushing interphone and door open button for 3 seconds(Screen setting and Call volume will be initialized)
Caution
If initialization is activated, all data including screen setting will be initialized) (Screen setting and Call volume)

Specifications and Features

4 wires with interphone(Polarity)
Rating Voltage| 100-240V~, 50/60Hz (FREE VOLTAGE)
Power consumption| Stand-by : 4.5W Maximum : 16W
Transmission way| HAND SET
Screen| 17.78Cm(7″) TFT-DIGITAL LC
Ringtone| Entrance : electronic chime
Interphone : electronic buzzer
Screen Display| Monitoring : 30 ±5sec , Talk : 60 ±5sec
Distance from Camera| 28m(Ф0.5) / 50m(Ф0.65) / 70m(Ф0.8)
Working temperature| 0 ~+40℃ (32℉ ~ 104℉)
Dimension| 311(W) X 168(H) X 32(50.3)(D)

COMMAX CO.,Ltd.
513-11, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea
Int’l Business Dept. Tel. : +82-31-7393-540~550 Fax. : +82-31-745-21 33
Web site :www.commax.com

References

• 코맥스 - Smart Home & Security

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>