GCteq GF17LITE Embedded Multi Functional Charging Table User Manual

Power freer
GF-17Lite Series
User manual

Instruction

Perspective View

Fixation for Installation

1. The bottom diameter of product is 247.6119.1mm,depth 37.2mm, The suggested size of Cut-Out is 252122.5mm , and a reasonable gap is reserved at the bottom to facilitate the heat dissipation of product, as shown in the figure below:
2. Putin the product, press down and screw in to fix:

Specifications

liner actuator
control| Click the button, the motor starts to run,
stop after the end of the trip| without a button
Click the button during operation, the motor
stops working;
Click the button again and the motor runs in
the opposite direction| without a button
Dimensions| 278141.847.2mm

Accessories list

Precautions

Please read and observe the following precautions carefully before installing and using this product:

1. Please supply power to the wireless charger using the original power adapter for this product.
2. The wireless charging distance of this product is 3-8mm (coil-coil)
3. Please ensure that there are no metal foreign bodies between the wireless charger and the mobile phone before charging, so as to prevent the metal foreign bodies from being heated by mistake.
4. Do not place magnetic cards such as bank cards and bus cardsinthe charging area to avoid damage tothe cards.
5. For a better wireless charging experience, please do not use the product beyond the maximum charging distance.
6. The heating and cooling functions can only be used after the charging moduleis screwed out.
7. If the charging module is manually toggled or not rotated properly, heating and cooling functions may not be available.
8. Please reserve space for cooling product.

Performance Features

1. With unique installation process, itcan realize convenient and quick installation.
2. It consists of three core functions including wireless charging, wired charging and actuator control (designated Model), which can meet different scenarios.
3. With intelligent power distribution, it can meet different application combinations.
4. It is compatible with wireless fast charging protocols of mainstream devices such as Apple 7.5W and Samsung 10W.
5. It provides A 18W and C30W (maximum) wired charging interface.

Instructions:

1. Make sure that your phone supports wireless charging, because the wireless charging requires the support of the wireless induction coil built into the phone(hardware);

2. When you power on the wireless charger, please make sure there is no magnetic object (metal, magnet, etc.) inthe charging area, then switch on the power, and place the mobile phone in the charging area ;

3. The wireless coil of different phones is located in different locations. The sensor area is generally located in the center of the phone. You need to make sure that the wireless coil ofthe phone is aligned with the center of the wireless charging area.
   When charging starts, the screen will light up toshow the charging prompt;

4. You need to pay attention to the limitation of charging distance for wireless charging. The distance between the phone and the wireless charger should not exceed the maximum charging distance of the product.

Common product faults

2.Unstable connection of power interface. 3.The charging distance is out of range. 4.There are other metal objects in the charging area.| 1.Replace the adapter that match. 2.Reinsert the power socket.
3.using within the specified distance. 4.Remove metal foreign bodies
Charging is slow| The temperature of product is too high| 1, Keep reasonable space for heat dissipation
2, Please wait until the temperature  drops to room temperature before using the device

Hazardous Substance Declaration

This mark is the product pollution control mark, the number of which represents the environmental service life. In this period of time, under normal conditions of use harmful substances will not cause greater pollution to the environment or damage to human life and property.

(PBDE)
Electronic components| X| 0| 0| 0| 0| 0
Plastic casing| 0| 0| 0| 0| 0| 0
Electroplated aluminum alloy parts| 0| 0| 0| 0| 0| 0
Non-electroplated metal parts| 0| 0| 0| 0| 0| 0
Double faced adhesive tape| 0| 0| 0| 0| 0| 0
Synthetic cork| 0| 0| 0| 0| 0| 0
Silicon parts| 0| 0| 0| 0| 0| 0

This form is in term of Stipulation SJ/T 11364
O It means that the content of the harmful substance in a part of the part is lower than the limit requirements specified in GB/T 26572.
X It means that the content of the harmful substance in a part of the part exceeds the limit requirements specified in GB/T 26572.

FCC STATEMENT:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occurina
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet ona circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth foran uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Product Warranty

The warranty services of repair, exchange and return are provided for wireless charger products in strict accordance with the provisions of Consumer Rights Protection Law of the People’ s Republic of China and Product Quality Law of the People’ s Republic of China.
The service contents are as follows:

• If any performance fault occurs in the product within 7 days from the day following the purchase (signature for receipt), you can enjoy the return or exchange services free of charge after testing and confirmation by the after-sales service center;
• If any performance fault occurs in the product within 8-15 days from the day following the purchase (signature for receipt), you can enjoy exchange or repair services free of charge after testing and confirmation by the after-sales service center;
• If any performance fault occurs in the product within 1 year from the day following the purchase (signature for receipt), you can enjoy repair services free of charge after testing and confirmation by the after-sales service center;

Non-warranty Provisions
The warranty services of repair, exchange and return are not provided in one of the following cases, and only repairis provided fora fee;

1. Damage is caused by consumers due to improper use, repair and storage;
2. Damage is caused due to the repairs not performed by authorized service providers designated by the Company;
3. No valid warranty services or invoices or proof of purchase can be provided;
4. Damage is caused due to force majeure.

Manufacturer: GCteq Wireless (Shenzhen) Co.,Ltd
Website: http://www.gcteq.com
Checked
Certificated of qualification

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>