ERKUL Skybar V2 Roof Rack Cross Bars Instruction Manual

ERKUL Skybar V2 Roof Rack Cross Bars

ATTENTION

• Don’t cut the bars or scrape the plastic headers! These crossbars are vehicle-specific and bar lengths vary by model.
• If one bar is longer than the other, the front of your vehicle is wider than the back.
• In this case, install the longer bar on the front and the shorter bar on the rear.
• If you can’t ft t, there may be a point you missed.
• If you cut the bars and don’t insert cross bars fully into the mount, the bar’s carrying capacity will decrease. In this case, Erkul Auto will not accept responsibility.
• If you need assistance please do not hesitate to contact us via your shopping channel.

PACKAGE INCLUDED

• Watch our installation video using the QR Code below.

ASSEMBLY INSTRUCTION

• Remove the protective sticker from the top and bottom of the bar before use. Check the lengths of the bars and use the long bar to the front if there is one.

2. a

• The thick side of the bar should face the front of the vehicle.

2. b

• Refer to the individual brackets, marked L for left and R for right.

• Rubber side has to face up.

• a) Loosen the horizontal screw which is circled in the picture. (you will tighten it later in the part 12)

• b)Insert the bar fully into the mount. If you don’t push it all the way long, the bar may stay long for the vehicle. (for some vehicles, an equal gap of 1-2 cm may occur)

• Clean and dry the vehicle’s roof rails.

• Place cross bars on roof rails so the outside of the mounts sit flush to the rails.

• The recommended distance between bars is 27 inches (70 CM). Do not try to increase this distance while carrying long products.

• Tighten the first screw until snug, approx. 50%.

• Tighten the opposite screw until snug, approx. 50%.

• Fully tighten screw from step 7.

• Fully tighten the screw from step 8.

• Repeat steps 7-10 for the second crossbar.

• Tighten the upper hex screw to secure the crossbar to the mount.

• Insert part C into mount before attaching part D.

• Part D must be unlocked before attaching to the mount.

• Insert part D and lock the cover in place

• Repeat steps 12-15 for the remaining 3 mounts

• To check the fitment, firmly grasp the load bars and attempt to move forward and backward, side to side.

Flexible RUBBER

• Flexible RUBBER for TRIM FREE T-TRACK MOUNT INSTALLATION

• Thanks to flexible rubber to install your carriers you don’t need to trim the rubber.

Note: T-tracks are not inclouded the package.

SAFETY PRECAUTIONS

1. Confirm that you have all the required parts by checking the assembly instructions.
2. Regularly check for worn-out or damaged parts and replace them.
3. Regularly clean and manage the load bars, especially during the winter.
4. Store all loose parts in a safe place when the product is removed.
5. Review and follow the assembly instructions and the suggestions list. Complete each step in the order recommended.
6. With the load bars installed, some sunroofs and/or radio antennas may not be operable, or some of their functions may be limited.
7. Except where otherwise stated in the mounting instructions, the load bars can be installed on cars with sunroofs.
8. Keep a minimum gap of 27 inches (700 mm) between the load bars.
9. Keep a mnm um distance of 23 inches (600mm) between the load bars while carrying heavy loads.
10. Ensure that the load bars are securely mounted on the roof each time they are installed. To check the security of the bars, firmly grasp them and attempt to move them forward and backward, as well as side to side. If any part of the unit moves, the mounting screws must be tightened to prevent movement. Check the security of the load bars regularly.
11. Do not exceed the maximum load limit of 165 lbs (75kg). This LMT may be less dependent on the maximum roof load recommended by the vehicle manufacturer. Always defer to the lowest maximum suggested roof load.
12. The maximum roof load is equal to the weight of the load bars plus any installed career accessories plus the weight of the load itself.
13.  Any items carried on the load bars MUST be securely fastened. The use of elastic bungees is not safe.
14. Surfboards and other long items must be fastened at both the front and back of the vehicle when being transported.
15. When transporting multiple surfboards, stack them one on top of the other rather than next to each other
16. The load must not be worse than the load bars with, and t must be equally distributed across the bars with the lowest possible center of gravity.
17. Before loading, all loose or removable pieces of the load, such as bicycle child seats, tire pumps, surfboard fins, etc. should be removed.
18. Skis must be installed with the ski tips facing the rear of the vehicle when being transported.
19. Check the load’s initial security after a short distance and at regular intervals on longer drives, at highway speeds, or on bumpy roads. When required, tighten the load’s fastening straps.
20. When carrying taller items such as upright bicycles, the total height of the vehicle rises significantly. Use caution when clearance is low or when entering parking structures.
21. When a load is carried on the roof, the vehicle’s handling and braking behavior can change, and it is more susceptible to cross-winds.
22. The vehicle’s speed must always be adjusted to the load being transported as well as current driving conditions, such as road type, road quality, wind conditions- ons, traffic intensity, and relevant speed limits, but speeds must never exceed 80MPH (130 km/h). Speed limits and other traffic restrictions must always be followed.
23. Drive slowly over speed bumps, with a top speed of 6 MPH (10 km/h).
24. While in use, lock any products that are equipped with locks.
25. This product may not be altered in any way.
26. The manufacturer will not be held liable for human or animal injury, property damage, or financial loss resulting from improper installation or use of the device. Always double-check that the load is properly secured

ATTENTION

MORE INFORMATION

USE THE QR BELOW TO SEE INSTRUCTIONS IN OTHER LANGUAGES

• support@erkulauto.com

CONTACT

LIVE CHAT SUPPORT

• IF YOU ARE MISSING ANY PARTS OF THE PRODUCT OR HAVING TROUBLE IN THE INSTALLATION PROCESS, PLEASE DO NOT RETURN THE PRODUCT BEFORE TEXTING US VIA THE QR CODES BESIDE.

• OUR LIVE AGENTS WILL BE HAPPY TO ASSIST YOU.
  You can also e-mail us for any other questions or further assistance.
  support@erkulauto.com

• WHATSAPP

• FACEBOOK MESSENGER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>