ATEN VP3520 5 x 2 True 4K Seamless Presentation Matrix Switch with Control User Guide
- June 5, 2024
- Aten
Table of Contents
ATEN VP3520 5 x 2 True 4K Seamless Presentation Matrix Switch with Control
User Guide
Package Contents
- 1 VP3520 5 x 2 True 4K Seamless Presentation Matrix Switch with Control
- 1 IR receiver
- 1 IR remote control
- 1 power cord
- 1 rack mount kit
- 1 foot pad set (4 pcs)
- 1 user instructions
Hardware Overview
FRONT VIEW
-
mic volume control
-
overall volume control
-
display selection pushbuttons
-
source selection pushbuttons
-
function selection pushbuttons
-
IR learn panel
-
IR learn LED
-
power pushbutton
REAR VIEW
- cable lock screw for ATEN LockPro™
- audio in
- mic in
- power socket
- power switch
- grounding terminal
- source 1, 2
- HDBaseT in
- source 3, 4, and 5
- HDMI in IR REMOTE CONTROL
- output / Display A
- HDBaseT out
- relay port 1 & 2
- output / Display B
- HDMI out
- RS-232 port
- IR port
- audio out
- stereo line out
- Lo-Z out
- coaxial out
- IR receiver port
- Ethernet port
- RS-232 serial port
IR REMOTE CONTROL
- on / off
- source
- display
- mute
- functions
- volume up
- volume down
Installation
- Use a grounding wire to ground the unit by connecting one end to the grounding terminal, and the other end to a suitable grounded object. Note: Do not omit this step. Proper grounding helps prevent damage to the unit from power surges or static electricity
- Connect up to 5 video sources to the unit.
- To connect a video source device via a video extender, connect the video extender (e.g., VE802T) to the VP3520 using an Ethernet cable.
- To connect an HDMI source device, connect the source device to the VP3520 using an HDMI cable. You can connect up to three HDMI source devices
- Connect up to two displays to the unit.
- To set up a display at a distance, connect a suitable Rx device (e.g., VE802R) to the VP3520 using an Ethernet cable, to which the display (e.g., projector) is connected. To remotely control the connected projector’s screen up and down, connect the screen to the relay ports.
- Connect the unit to an HDMI display using an HDMI cable. To remotely control the connected display, connect the RS-232 and IR ports to the display
- (Optional) To supply independent audio, connect an audio source device (e.g., media player) or a microphone to the VP3520.
- Optional) Connect the VP3520 to a speaker via an appropriate audio out port.
- (Optional) To confi gure the unit’s settings via RS-232 commands, connect a hardware controller (e.g., ATEN Control Box) to the VP3520.
- (Optional) To allow access to the web interface, connect a network switch to the VP3520 using an Ethernet cable.
- (Optional) To control the VP3520 using an IR remote control, connect the IR receiver to the VP3520.
- Plug the power cord to the power socket
- 0 Put the power switch to ON.
- Press the power pushbutton to power on the VP3520.
- 2 Power on all the connected devices.
OPERATION
You can operate the unit using the front-panel pushbuttons, IR remote control, RS-232 serial controller, or the web interface. See the user manual for detailed information. To log in the web interface, use the default IP address 192.168.0.60 and the default credential ( administrator / password ).
Support and Documentation Notice
All information, documentation, firmware, software utilities, and
specifications contained in this package are subject to change without prior
notification by the manufacturer.
To reduce the environmental impact of our products, ATEN documentation and
software can be found online at
http://www.aten.com/download/
Technical Support
Scan for more information
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
© Copyright 2021 ATEN® International Co. Ltd.
ATEN and the ATEN logo are registered trademarks of ATEN International Co.,
Ltd.
All rights reserved. All other trademarks are the property of their respective
owners
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>