shopify CB1R Event Lighting Crowd Barrier Corner User Manual
- June 5, 2024
- shopify
Table of Contents
shopify CB1R Event Lighting Crowd Barrier Corner
For your safety, please read this user manual carefully before initial
use.
Event Lighting reserves the right to revise the manual at any time.
Information and specifications within this manual are subject to change
without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Safety Instructions
Warning
- It is recommended that two people lift each CB1R Crowd Barrier Corner into place. Please observe your local occupational health and safety guidelines.
- There must be at least two CB1 Crowd Barriers on either side of the CB1R Crowd Barrier Corner, as the units locks together using latches and bolts. A single unit on its own will not be effective and runs the risk of collapse.
- There must be at least two x CB1 Crowd Barriers placed in between any CB1R Crowd Corner and CB1G Crowd Barrier with Gate.
- In order to set up an effective crowd barrier, the CB1R crowd barrier corner must be set up as an internal corner, and all latches and bolts must be done up to avoid the risk of collapse or gaps forming between pieces, that may result in injury.
- In situations where a high number of people may be present, it is recommended that there is crowd control employed, to avoid the risk of excessive force being placed on the crowd barrier.
- When there is a crowd and they are pushing and moving the barrier, periodic checks are to be made on all coffin latches and bolts to ensure that the crowd barrier is still intact and not damaged. Intervals of your periodic checks will be determined by your risk assessment of the event, where the crowd barrier is being used.
- The CB1R crowd barrier corner, the CB1G crowd barrier gate and the CB1 crowd barrier, should only be used on a flat surface.
Unpacking
Each CB1 Crowd Barrier comes with a bolt that is used to secure the CB1R Crowd Barrier nCorner to the next unit, and lock the upright into place. Upon unpacking, this bolt is in a zip lock bag, attached to the frame of the crowd barrier CB1. This bolt is used to secure the CB1R into place.
Set Up of CB1
- Place the first flattened CB1 unit on flat surface, with the sloped front facing in the direction that the crowd will be.
- Lift the wall, which has a curved top, from the end of the sloped front, towards an upright position. The smaller frame, hinged to the wall, should fall in place as the wall is raised, resting behind the crowd-facing side of the wall. By pushing near the bottom of the wall from behind, be sure that the wall is as close to the platform as possible.
- Set Up of CB1R
- Lay the CB1R – Crowd Barrier Corner in line with the previous unit, with the sloped front facing in the direction the crowd will be, using the bolt inserted to the previous unit as a guide to line up the crowd barrier corner. Lift the corner into place, following the same method as the previous crowd barrier unit.
- Push the bolts through both units, until there is enough room to tighten the nut to the bolt. Be sure to tighten the nut, using a spanner.
- Using an allen key, turn the floor latch anti clockwise until it has grabbed onto the adjacent unit and can move no further.
- Using an allen key, turn the wall latch anti clockwise until it has grabbed onto the adjacen unit and can move no further.
- Once the latches are secure, the crowd barrier is in place. Repeat the process until the wall is complete
Note:
- To prevent movement while setting up, place the provided bolt partially through the hole in the wall frame, so it makes contact with the floor frame. Later, this bolt will be pushed into the next adjoining unit CB1R Crowd Barrier Corner.
- Ensure the hand rails line up where they should be, if not loosen up the bolts with the allen key and the coffin latch and realign and tighten again
- that all barriers and gates will follow a similar process, refer individual manuals on correct and safe way to connect those components.
Undoing.
Using an allen key, turn the latches clockwise to undo, making sure to turn all the way to release each part from each other. Always start from outer-most units first Loosen nut of floor holding screw, and remove screw. Lift smaller frame behind wall and carefully push forward on the wall part from near the base, while standing on the floor and lower the wall towards the collapsed position, making sure the smaller frame folds in with it. Be sure to keep hands and fingers away from folding parts. Repeat process for each unit of crowd barrier
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>