Breville LAH400 Smart Mist Humidifier Instruction Manual

the Smart MistTM Humidifier

Instruction Book – LAH400

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care and adhere to the following precautions.

Product Dimension: 353x230x184mm
For Room Size: 20 to 40m2
Noise Level: Up to 43dB
Power Consumption: 110W
Weight: 2.4kg
Water Capacity: 5L
Evaporation Rate: > 260ml/h

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE:

• Carefully read all instructions before operating the humidifier for the first time and save for future reference.

• Remove and safely discard any packaging material and promotional labels before using the humidifier for the first time.

• To eliminate a choking hazard for young children, remove and safely discard the protective cover fitted to the power plug of this humidifier.

• When unpacking the humidifier, check to see you have received all the items listed in the parts list before discarding the packaging.

• Always ensure the humidifier is properly assembled before use. Follow the instructions provided in this book.

• Always operate the humidifier on a stable surface. Ensure that the surface is level, clean and free of water and other substances.

• Do not operate the humidifier on an incline plane. Do not move while the humidifier is switched on.

• Do not place the humidifier near the edge of a bench or table during operation.

• Do not place the humidifier on a rug, carpet, wooden flooring, or any other surface that may be damaged by exposure to water or moisture. It is recommended that a waterproof mat or pad is placed under the humidifier.

• Do not operate the humidifier on a sink drain board.

• Do not locate the humidifier directly below or close to a mains electricity supply socket.

• Do not use the humidifierwithout water in the water tank.

• Do not use the humidifier unless it has been cleaned according to instructions.

• Mist may not be visible in certain conditions (impacted by light, background colour, etc.) or at lowest setting.

• Suitable for use in drylocations only. Do not use outdoors or on wet  surfaces. Do not use in bathrooms, laundry areas or similar indoor locations.

• Never place the humidifier where it may fall into a bath or other water container.
  Do not use or store where it may get wet or in the immediate surroundings of a bath, a shower, or a swimming pool.

• Do not use in areas where petrol, paint, or flammableliquids are used or stored or where there are vapours present. Do not use in conjunction with or directly next to an air freshener or similar products.

• Do not spray any flammable materials such as insecticides or fragrance around thehumidifier.

• Do not use this humidifier when you have used indoor smoke-type repellents or in places with oily residue, burning incense or chemical fumes.

• Do not pour water into any openings except for the water tank. Do not allow water toenter the air outlets on top of the humidifier.

•  When filling or refilling, only fill the water tank with cold tap water or distilled water.
  Do not use ground water or hot water.

• Always switch the humidifier off and then unplug from the power outlet: – Before filling or emptying the water tank. – Before cleaning and maintenance, unless otherwise specified in this booklet. – Immediately after use.

• Always use clean tap or distilled water to prevent clogging and damage to the transducer.

• Do not put any substance other than water in the water tank. Do not add fragrance orany chemical substance into the water. Use  only water (tap, purified, mineral, any sort of portable water). If other additives are used, the plastic material and the membrane may become discoloured and/or damaged.

• Water in the water tank is not suitable for drinking. Do not drink this water, and do not use it to feed animals or water the plants. When you empty the water tank, pour the water in the water tank down a drain.

• Do not use the humidifier in a room with majortemperature changes as this may cause condensation inside the humidifier.

• If not using the humidifier for a long time, clean and dry the water tank before storage.

• Clean the water tank every week.

• Always disconnect the humidifier from the power supply and empty the water tank before moving. Always carry the humidifier upright.

• It is important to check the humidity of your ambient air regularly. Intensive continuous operation can cause the ambient air to become excessively humid.

• A comfortable humidity level is considered to be between 40%RH to 60%RH.

• Never use the humidifier underneath a cover such as a blanket, pillow, etc.

• Never plug in or switch on the humidifier without filling the removable water tank with water and correctly replacing the tank onto the base of the humidifier.

• Do not remove the mistnozzle during operation.

•  Position the humidifier so that the mist nozzle is not directed towards objects or a wall as the immediate vicinity of the air humidifier may become damp.

• The humidifier is not intended to be operated by means of an external timer or separate remote-control system or any other device that switches the humidifier on automatically.

• Do not use chemicals, steel wool, metal scouring pad or abrasive cleaners to clean the outside of the humidifier housing as these can damaged the housing of the humidifier.

• Cleaning procedures must be routinely followed to ensure that the humidifier continues to operate efficiently.

• Empty any remaining water from the water tank and water inlet basin when the humidifier is not in use.

• You may optionally add drops of essential/scented oils to the aroma tray. This will emita pleasant odour into thesurrounding area.

• The air humidifier transducer is highly sensitive. Do not touch the transducer with bare fingers or scrape it with any metal tools, as it may reduce the mist output permanently.

• Keep the humidifier clean. Follow the cleaning instructions provided in this book.

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES

• Fully unwind the power cord before use.

• Connect only to a 230V or 240V power outlet.

• Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted.

• To protect against electric shock, do not immerse the power cord, power plug or appliance in water or any other liquid or allow moisture to come in contact with the part, unless it is recommended in the cleaning instructions.

• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• It is recommended to regularly inspect the appliance. To avoid a hazard, do not use the appliance if power cord, power plug or appliance becomes damaged in any way. Return the entire appliance to the nearest authorized Breville Service Centre for examination and/or repair.

• Any maintenance other than cleaning should be performed at an authorised Breville Service Centre.

• This appliance is for household use only. Do not use this appliance
  for anything other than its intended use. Do not use in moving vehicles or boats. Do not use outdoors.
  Misuse may cause injury.

• The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice.

• During electrical storms,the appliance should be disconnected from the  power source at the wall socket to prevent any electrical surges that may arise during the storm and which may inadvertently cause damage
  to the appliance and it selectronic componentry.

• Always turn the appliance to the off position, switch off at the power outlet and unplug at the power outlet when the appliance is not in use.

• Before cleaning, always turn the appliance to the off position, switch off at the power outlet, unplug at the power outlet and remove the power cord, if detachable, from the appliance and allow all parts to cool.

• Do not place this appliance on or near a heat source, such as hot plate, oven or heaters.

• Position the appliance at a minimum distance of 20cm away from walls, curtains and other heat or steam sensitive materials and provide adequate space above and on all sides for air circulation.

Components

A. Mist Nozzle
B. Top Cover
C. Water Tank Handle
D. Water Tank
E. Water Purification Filter
F. Water Tank Cap
G. Heating Element
H. Water Inlet Basin
I. Blue Power Indicator Light
J. Water Buoy
K. Transducer
L. Base
M. Aroma Tray
N. Front Panel
O. Control Area
P. Remote Control
NOT PICTURED
Sensor (located on power cord)
Power Cord
Aroma Tray Felt Pad
Non-slip Feet

Control Panel

A. Power On/Off
B. Mode
C. Mist Level Control Scroll left or right to change the mist level.
D. Night/Sleep
E. Warm Mist
F. Timer
G. Humidity Setting

Display Screen Icons

Auto
Night
Humidity
Baby
Water Empty
Health
Warm Mist
Timer

Features

WHAT IS A HUMIDIFIER?

Your Breville humidifier will assist in keeping a comfortable and healthy environment at home by artificially adding water vapour (moisture) to the surrounding atmosphere. It may assist with common winter symptoms such as dry skin, dry throat, cracked or dry lips, dry nasal cavity, and itchy eyes, as well as some sinus and respiratory issues.

HOW DOES A HUMIDIFIER WORK?

Your Breville humidifier uses a high-frequency oscillator to break water into tiny water particles. The ventilation system then blows these water particles into the dry air in the form of a mist where it evaporates to increase the relative humidity.

WHAT IS RELATIVE HUMIDITY?

Relative humidity (RH) is the amount of water vapor in the air and it is commonly expressed as a percentage of the maximum amount of water vapor that the air can hold at a given temperature. Every environment has a different humidity level. A standard comfortable level is considered to be between 40-60%RH.

Assembly

BEFORE FIRST USE

1. Before using your humidifier for the first time, remove all packaging material and promotional labels.

2. Check for any missing or damaged parts as per the components list.

3. Clean all parts according to the Care, Cleaning & Storage section.

4. Place the humidifier on a flat surface that will not be damaged by exposure to water or moisture.

5. Remove the cover from the top of the
   humidifier and set aside.

6. Using the handle, lift and remove the water tank from the humidifier.

7. Turn the water tank gently upside-down, unscrew the water tank cap and fill the tank with clean water.

8. Replace the water tank cap securely back onto the water tank and place the tank onto the humidifier base.

9. Replace the top cover with the nozzle back on top of the water tank.

10. Connect the power plug to a 230V or 240V power outlet and switch the outlet on. The POWER symbol will illuminate red. The humidifier is now in Standby mode.

11. Touch the POWER symbol again to activate the control panel and display screen. The humidifier is now switched on and will automatically begin operation in Auto mode.

Functions

YOUR BREVILLE HUMIDIFIER

• The control panel lights will dim after 15 seconds if not touched. Touch the centre of the control panel where the control symbols are located to wake up the screen.
• The Timer feature can be used in any mode.
• The humidifier will check the humidity level once every minute.
• Manual adjustment of the Mist intensity control bar will exit any programmed settings, except Night mode and manual Humidity setting.
• Touch and hold the WARM MIST symbol to turn off the blue light in the water tank. Repeat to turn back on.
• The humidifier will automatically turn off if it has insufficient water to operate. Any programmed operating setting will be cancelled if the water tank runs empty.

SensAir™ LIVE COMFORT CONTROL

• Your Breville Smart Mist™ Humidifier has a sensor to detect changes to humidity and temperature in the surrounding area.
• The SensAir™ can automatically keep the humidity in “the Sweet Spot” by setting the appropriate level of relative humidity, depending on ambient air temperature for maximum comfort.

OPERATING YOUR HUMIDIFIER

AUTO MODE

• AUTO mode is the default setting for the humidifier when turned on from standby. Auto mode can also be manually selected.
• The Timer feature and Warm Mist feature can be used with this setting. Mist Intensity cannot be manually adjusted.

1. Touch the MODE symbol on the control panel until the AUTO icon illuminates on the display screen.
2. Auto mode automatically adjusts the mist intensity to regulate the humidity level between 40-65%RH based on the temperature within the room.
3. The humidifier will continue to monitor and regulate the mist intensity as required to maintain the relative humidity level.
4. If the Timer has not been programmed, the humidifier will continue to operate in Auto mode until turned off or programmed to another mode.

HEALTH MODE

• In HEALTH mode, the humidifier automatically adjusts the mist intensity to maintain a relative humidity level of 60% and activates the   WARM MIST feature.
• The Timer feature can be used with this setting and the Warm Mist can be turned off, if desired. Mist Intensity cannot be manually adjusted.

1. Touch the  MODE symbol on the control panel until the HEALTH icon and the WARM MIST icon both illuminate on the display screen.
2. Once relative humidity has reached 60%,the humidifier will continue  to monitor and regulate the mist intensity maintaining the 60% relative humidity level.
3. If the Timer has not been programmed,the humidifier will continue to  operate in Health mode until turned off or programmed to another mode.

BABY MODE

• In BABY mode, the humidifier automatically adjusts the mist intensity to maintain a relative humidity level of 55% and activates the WARM MIST feature.
• The Timer feature can be used with this setting and the Warm Mist can be turned off, if desired. Mist Intensity cannot be manually adjusted.

1. Touch the MODE symbol on the control panel until the  BABY icon and the WARM MIST icon both illuminate on the display screen.
2. Once relative humidity has reached 55%, the humidifier will continue to monitor and regulate the mist intensity maintaining the 55% relative humidity level.
3. If the Timer has not been programmed, the humidifier will continue to operate in Baby mode until turned off or programmed to another mode.

NIGHT MODE

• In NIGHT mode, the humidifier turns off the lights, except the blue water tank light. The humidifier will operate in Auto mode.
• The Timer feature and Warm Mist feature can be used with this setting. Mist Intensity cannot be manually adjusted.

1. Touch the NIGHT symbol on the control panel. The  NIGHT icon will illuminate on the display screen.
2. After 15 seconds, all the lights will turn off, except the blue water tank light and the NIGHT icon on the display screen.
3. Touch the centre of the control panel to reactivate the control panel.
4. Touch the  NIGHT symbol again to cancel. The control panel lights will illuminate and the humidifier will continue to operate in
   Auto mode.

MANUAL MODES

This humidifier can be manually programmed in four ways:

1. MIST INTENSITY CONTROL

• This humidifier has 7 mist intensity levels which can be manually selected between Low (1) to High (7).
• The Timer feature and Warm Mist feature can be used with this setting.

1. Touch or slide your finger along the MIST LEVEL CONTROL bar on the control panel to change the intensity. The intensity level will show on the display screen.
2. Select another program or touch the POWER symbol to cancel.

2. HUMIDITY SETTING

• The humidity level can be manually selected between 30% and 75%RH.
• The Timer feature can be used with this setting.

1. Touch the HUMIDITY symbol on the control panel repeatedly to cycle through 30% to 75% RH. The HUMIDITY icon will illuminate on the display screen.

2. When the desired relative humidity level is
   displayed, it will flash 5 times before starting.
   Once activated, the current humidity level will
   return to the display screen.

3. Once the humidity reaches the selected level, the humidifier will continue to monitor and regulate as required to maintain that level, adjusting the mist intensity and turning the mist off and on. Touch the  HUMIDITY symbol to check the selected relative humidity level.

4. Touch and hold the  HUMIDITY symbol until the  HUMIDITY icon disappears from the display screen or touch the POWER symbol to cancel.

5. If Warm Mist is needed, it can be selected when the desired humidity level is above the room humidity level.

6. If ‘- -‘ flashes on the display screen, it is a reminder that a humidity level has not been set. It will flash for 5 seconds, then return the humidifier to Auto mode.

3. TIMER

• This humidifier has a Timer feature that will turn the humidifier off after a chosen number of hours.

1. Touch the TIMER symbol on the control panel repeatedly to cycle through 1 to 12 hours. The TIMER icon will illuminate on the display screen.
2. When the desired number of hours is displayed, it will flash 5 times before starting the countdown. Once activated, the temperature will return to the display screen.
3. The Timer will begin to count down in 1-hour increments. The humidifier will automatically turn off once the chosen time has elapsed.
4. Touch and hold the  TIMER symbol until the  TIMER icon disappears from the display screen to cancel this feature.
5. If ‘- -‘ flashes on the display screen, it is a reminder that the timer has not been set. It will flash for 5 seconds, then return the humidifier to Auto mode

4. WARM MIST

• This humidifier has a Warm Mist feature. A small internal heating element will heat the water to create a warm vapour.
• The WARM MIST operates automatically in Health and Baby modes or can be manually selected in other programmes.

1. Touch the  WARM MIST symbol on the control panel to turn on. The  WARM MIST icon will illuminate on the display screen and warm mist will emit from the mist nozzlegradually within 10-15 minutes.
2. Touch the  WARM MIST symbol again to turn.

AROMA TRAY

• Press the aroma tray on the side of the humidifier and it will click out of the unit.
• Add 2–3 drops of essential oil (not included) directly to the pad in the aroma tray.
• Push the aroma tray back into the humidifier until it clicks into place.
• Turn the humidifier on and the aroma will start emitting automatically with the mist. Increase the mist intensity as desired.

AUTO SHUT-OFF

• Once the water in the water tank and water inlet basin is too low to keep the machine running, the WATER EMPTY symbol will illuminate red on the display screen for 5 minutes and the humidifier will stop working. The POWER symbol will turn red and stay illuminated.
• Fill the water tank, turn the humidifier on and program the desired mode.

USING THE REMOTE CONTROL

The humidifier comes equipped with a remote control which can be used to operate all the functions on the humidifier.

• A CR2025 3V Lithium battery is provided with the remote. When it is time to replace the battery, open the battery compartment at the back of the remote, pushing the small arched groove to the right and simultaneously pulling out the battery compartment cover by pushing the rectangular groove.
  

• Insert the battery, paying attention to the polarity (+ and -). Reinsert the battery compartment into the remote control ensuring that the + symbol is facing upwards when inserted. Make sure the battery compartment is correctly secured.
  

• To use the remote control, point it at the display screen on the humidifier and used within five meters.

• HINT: When correctly inserted, the text on the battery will be facing the bottom of the remote and the compartment is fitted correctly when it slides in all the way.

WARNING FOR
BUTTON BATTERIES

KEEP OUT OF REACH OF CHILDREN

• Swallowing may lead to serious injury in as little as 2 hours or death, due to chemical burns and potential perforation of the oesophagus.
• If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons information Centre on 13 11 26 for fast, expert advice.
• Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if compartment is not secure.
• Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.
• Tell others about the risk associated with button batteries and how to keep their children safe.

Care, Cleaning & Storage

Before cleaning, ensure the power is switched off and then remove the power plug from the power outlet.

BREVILLE RECOMMENDS

• Only use cold water or distilled water in the water tank.
• Change the water often to keep it fresh.
• Clean the transducer, water tank and waterbasin at a minimum of once  every week when in constant use.
• Use a small brush or a cotton swab to assist with cleaning the transducer and basin. Never usemetal or sharp objects.
• After cleaning, ensure all parts are completely dry before using the humidifier.

TO CLEAN EXTERNAL PARTS

• Use a clean, dry cloth to clean all external surfaces of the humidifier.
• A soft, slightly-damp cloth may be used to wipe the external housing of the humidifier if more thorough cleaning is required. Never use chemical substances or scourers as this could damage the housing and the control panel.
• Dry thoroughly before storing or using the humidifier.

TO CLEAN INTERNAL PARTS

In cases when the water is hard (where water contains too much calcium and magnesium), leave heavy scale on the surface of water basin, transducer and inner surface of the water tank. Scale, or calcification, on the surface of transducer will reduce the reliability of the unit. To clean internal parts of the humidifier, create a cleaning solution of 1-part vinegar to 1-part water.

WATER TANK

• It is important to clean the water tank regularly and ensure it is dry before reassembling andusing the humidifier.
• To clean, create a vinegar and water solution enough to fill the tank about half way. Making sure the cap is replaced on the tank, swish the solution around for a minute, then fill the rest of the tank up with tap water. Leave to sit for 1–2 hours, or even overnight.
• Empty and rinse well with clean water.

MIST NOZZLE

• If the mist output is reducing due tocalcification, turn the top cover over  and immerse the nozzle in a vessel filled with vinegar and water solution and soak for at least 10 minutes.
• Rinse with clean or distilled water and allow to dry.

WATER INLET BASIN

• The water inlet basin includes the water reservoir in the base of the unit that also houses the transducer and the heating element.
• Clean the water basin with a soft cloth. If thereis excess film or  calcification on the surface, then soak the cloth with the vinegar and water solution and repeat the process.
• If there is film or calcification in any of the depressions along the basin, drop a bit of vinegar and water solution into the depression and lightly clean it with a brush or a cotton swab.
• Rinse with clean or distilled water and allow to dry.

OPTIONAL CLEANING SOLUTION FOR CALCIFICATION ISSUES

• If a build-up of calcification on the transducer or heating element occurs and cannot be removed with a simple vinegar and water solution, use a de-calcifying agent or citric acid. STRICTLY FOLLOW THE INSTRUCTIONS ON THE PACKAGING FOR THESE CLEANING PRODUCTS.
• Brush off any scale deposits from the transducer and heating element surfaces using the brush or a cotton swab.
• Rinse with clean or distilled water and allow to dry

WATER PURIFICATION FILTER

It is recommended that you clean the water purification filter every time you clean the humidifier, especially if in frequent use. If the filter is cleaned regularly and as per instructions, it should last for the life of the humidifier.

• Remove the cover from the top of the humidifier and set aside.

• Using the handle, remove the water tank from the humidifier.

• Turn the water tank gently upside down and remove the water tank cap.

• The water purification filter is connected to the water tank cap. Unscrew the filter from the cap to clean.
  

• Dip the filter cartridge in a vinegar and water solution for about 10 minutes before thoroughly rinsing with clean water. Alternatively, rinse the filter under running tap water for a minute.
  

• Once clean, place the filter in direct sunlight and allow to dry for at least an hour.

• Reconnect the filter to the water tank cap, then screw the cap onto the water tank.

• Turn the water tank the right-side up and place the tank onto the base carefully.

• Place the nozzle and top cover on top of the water tank

STORAGE

• Never store the humidifier with water in the unit.
• Clean as per instructions and make sure that all parts are dry before storing.
• Allow the water tank and water inlet basin time to dry thoroughly before storing the humidifier.
• Keep the humidifier in a dry cool place.
• Do not place anyhing on top of the humidifier.

Troubleshooting

TROUBLESHOOTING GUIDE

Before carrying out any of the following service checks, unplug the unit from the mains.

Breville Customer Service Centre

Australian Customers
Phone: 1300 139 798
Web: www.breville.com
New Zealand Customers
Phone: 0800 273 845
Web: www.breville.com

Breville LAH400 Smart Mist Humidifier Instruction Manual – Optimized PDF
Breville LAH400 Smart Mist Humidifier Instruction Manual – Original PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>