Ustellar UT99911-RGBCW Smart Monitor Light Bar User Guide

Ustellar UT99911-RGBCW Smart Monitor Light Bar

Smart Monitor Light Bar User Guide

Thank you for ordering from Ustellar. Set-up is easy and takes only a few minutes by following the instructions.
The smart light can work with both Amazon Alexa and Google Assistant. But the light aner being installed will need to be paired with an app called ‘Smart Life’ first, and then the Smart Life app will need to be bound with either Amazon Alexa or Google Assistant to activate the voice control function. Therefore, this user guide consists of four parts. Parts one and two are fundamental setups, while parts three and four are Alternatives. If you use Amazon Alexa for voice control, please follow instructions on parts one, two, and three. If you use Google Assistant for voice control, please skip part three, and follow the instructions on parts one, two, and four.

How to install the light?

Warning

1. Please check if the light and the parts are intact before installation.
2. Make sure to cut off power before installation.
3. Please do not place this light in corrosive conditions.
4. If there is any damage to the cord, please cut off the power and stop using it immediately.
5. Please do not retrofit the light within the warranty period.
6. To ensure the light works properly, please use the voltage indicated on the packing.

Parameters

P/N

| UT99911-RGBCW-US-1 UT99911-RGBCW-EU-1 UT99911-RGBCW-UK-1
---|---
Model| UT99911
Rated Input| **
Rated Power| 10W
Color| RGB, Cool White, Warm White
Color Temperature| 2700-6500K
CRI| >90
Life Expectancy| 50000H
Lamp Size| Φ23 x 485mm / Φ0.9 x 19in
Working Temperature**| -20~40℃

Components

Product Description

1. RGB Light ON/OFF Buon: Short Press to power the RGB light ON/OFF. Long Press 5 seconds to reset the lamp for APP connection.
2. RGB Mode Switch Buon: Press to switch between 4 working modes: Gradient mode, Symphony mode, Adjoint mode, and Classic Music mode.
3. Color Temperature Switch Buon: Press to switch between 3 color temperatures of white light: 2700K(Warm Light), 4000K(Neutral Light), and 6500K(Cool Light).
4. White Light Brightness Buon: Press to adjust the white light brightness (circularly): 1%, 20%, 40%, 60%, 80%, 100%.
5. White Light ON/OFF Buon: Press to power the white light ON/OFF.

Installation

Step 1: Place the lamp with a clip on top of your monitor frame, and make sure the lamp is well fixed.

Step 2: Plug in the power supply for the lamp.

Note:

1. There is no battery in the lamp.
2. The power input of the lamp is 5V/2A, it is highly recommended to use the charger provided in the package for the power supply.

How to pair the light to the Smart Ufe app?

Before starting the paring, please malt& sure to tum on Iha BluataaCh and WiFi on your phone.
The Barnard light only supports 2.4GHz: WiFi woolwork. not 6.0GHz. Pllla&e make sure your working network is 2.4GHz, and your phone is 01111nactad to it. If your WiFi rou1ar supports both 2.4GHz and 6.0GHz. plaa&e separate the two frequency bands in the router aetlinga, and &elect the 2.4GHz for connection
Step A: Smart Life app installation
Please choose either wav below to download and install the app.

1. As per your phone system, choose the Q.R code to scan
2. Search keyword ‘Smart Lif’e’ in Apple Store or Google Play.

Step B: Create an account on Smart Uf’e and log in.
Note: Please keep your account and password In mind for Ale, ca, or Google Assistant App pairing later.

Step C: Add the light to Smart Life App

1. Tap’+’ button on the top right corner to add devices. Tap ‘Lighting’, then choose ‘PIR Light (BLE+Wi-Fi)’ to add the lights.
2. Power on the lamp. Long Press the RGB Light ON/OFF Button ( button on the front panel) for 5 seconds, to create the RED light into rapid blinking status, and the lamp will be reset. Then click the next button on this page.
3. Choose your WiFi network, enter your password, and tap the ‘Next’ button. Then give a name to the light and tap the ‘Done’ button.

Step D: Give a name to the light.

1. A simple name is recommended for easier voice recognition with Alexa or Google Assistant.
2. The name given to the light will be the same for voice control on Alexa or Google Assistant.
   Step E: The named light will be shown on the app homepage. Now you can control the light (turn on/off, change colors, adjust brightness, etc) with Smart Life on the setting page.

How to control the light with Amazon Alexa?

Please make sure that your Alexa app is connected to Echo and that both work well under your WiFi network.

Step C: Enter your Smart Life App account and password. Tap ‘Link Now’, then tap ‘Authorize’ on the next page to bind the Smart Life account to Alexa.
Step D: When your Smart Life account is bound to Alexa, tap ‘DISCOVER DEVICES’ to detect the light.

Step E: When the named light is paired to Alexa from Smart Life, it will show on the device page (see the ‘smart light’ example).

Step F: Now you can control the light with Alexa App on the setting page. To turn on or off the light, simply tap the bulb icon.
Step G: You can also voice control the light with Alexa by giving these commands: “Alexa, turn on ‘device name’ 1111Alexa, set ‘device name’ to ‘color’ 11
, Alexa, set ‘device name’ to ‘number'”. Device name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “Alexa, turn on ‘smart light'”, etc.

Note: To control the light with Google Assistant, please continue to read Part Four.

How to control the light with Google Assistant?

Step A: Login Google Assistant App, and tap ‘Home Control on the left sidebar page.

Step B: Tap + button on the bottom right to enter the next page.

Step C: Find ‘Smart Life’ from the sidebar list.

Step D: Enter your Smart Life App account and password to bind your Smart Life account to Google Assistant.

Step E: You will find the named light shown on the Home Control page. Now you can control the light on Google Assistant App, or voice control it by giving these commands: “ok Google, turn on ‘device name’ “, “ok Google, set ‘device name’ to ‘color”, “ok Google, set ‘device name’ to ‘number”. The device name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “ok Google, turn on ‘smart light’ “

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>