Ustellar UT33360-RGB-EU-NF LED RGB Light Strip User Guide

June 5, 2024
Ustellar

Ustellar-logo

Ustellar UT33360-RGB-EU-NF LED RGB Light Strip

Ustellar-UT33360-RGB-EU-NF-LED-RGB-Light-Strip-PRODUCT-
IMAGE

THANK YOU for choosing Novostella. To optimize user experience, please use the product according to the following instructions.
Warning

  1. Winding lighting is prohibited, as it affects heat dissipation and might cause dangers.
  2. Please unroll the light strip from the plate before lighting it up.
  3. Please check if the light strip and the parts are intact before using them.
  4. Please make sure that the power supply is turned off before installation.
  5. Please use the attached power adapter only, to ensure that the light works properly.
  6. Please do not use this light in the open air or under humid environment.

SPECIFICTAION

P / N UT33360-RGB-EU-NF  I    UT33360-RGB-UK-NF
Model UT33360-RGB-EU-NF  I    UT33360-RGB-UK-NF
Wattage 12W
Color RGB
Total Length 20ft/6m
LED Type SOSO
LEO Quantity 108 LEDs
Input Voltage 100-240V AC
Frequency S0/60Hz
Working Voltage 24V
Working Temperature -2s·c~4o•c
Restriction Indoor Use Only
Battery Type CR2025 (for remote controller)
Package Includes Light Strip x 2,Remote Controller x 1, Power Adapter x 1,LED

Signal Receiver x 1
P/N| UT33361-RGB-EU-NF
I  UT33361-RGB-UK-NF
---|---
Model| UT33361-RGB-EU-NF
I  UT33361-RGB-UK-NF
Wattage| 24W
Color| RGB
Total Length| 40ft/ 12m
LED Type| SOSO
LED Quantity| 210 LEDs
Input Voltage| 100-240V AC
Frequency| 50/60Hz
Working Voltage| 24V
Working Temperature| -2s·c~4o•c
Restriction| Indoor Use Only
Battery Type| CR2025 (for remote controller)
Package Includes| Light Strip x 2, Remote Controller x 1, Power Adapter x 1,LED Signal Receiver x 1
P/N| UT33362-RGB-EU-NF           I     UT33362-RGB-UK-NF
---|---
Model| UT33362-RGB-EU-NF  I    UT33362-RGB-UK-NF
Wattage| 24W
Color| RGB
Total Length| 65.6ft / 20m
LED Type| 5050
LED Quantity| 340 LEDs
Input Voltage| 100-2401/ AC
Frequency| 50/60Hz
Working Voltage| 24V
Working Temperature| -2s·c~4o•c
Restriction| Indoor Use Only
Battery Type| CR2025 (for remote controller)
Package Includes| Light Strip x 2, Remote Controller x 1,
Power Adapter x 1,LED Signal Receiver x 1

Components

Light Strip

RF Remote Controller

Power Adapter

LED Signal Receiver

Note: Power Adapter Cord – type Z attachment. For type Z attachment: The cable or cord cannot be replaced without breaking or destroying the luminaire.

LED Signal Receiver

Ustellar-UT33360-RGB-EU-NF-LED-RGB-Light-Strip-05

Access Port for 12/24V DC Power Adapter

4-Pin Access Port for Light Strip

RF Remote Controller

  • Brightness
  • Singular color
  • Diy color
  • Pause/Play
  • On/Off
  • Music Modes
  • Speed
  • Dynamic Mode

Dynamic Mode

There are 6 preset dynamic modes, and their speed can be adjusted with the “QUICK”or”SLOW” button.

  1. JUMP3: Flash and loop among 3 colors (Red, Green, Blue).
  2. JUMP7: Flash and loop among 7 colors (Red, Green, Blue, Yellow, Purpple, Cyan, White).
  3. FADE3: Fade and loop among 3 colors (Red, Green, Blue).
  4. FADE7: Fade and loop among 7 colors (Red, Green, Blue, Yellow, Purpple, Cyan, White).
  5. FLASH: Flash on white color only.
  6. AUTO: Loop among the above 5 dynamic modes. The FLASH mode (white color only) repeats 20 times, while the rest four modes repeats 4 times in each loop.

How to DIV colors?

This light strip is made of RGB LEDs, which means there are three colors (red/green/blue) on one LED. All lighting colors are made by changing the
ratio of red, green and blue on the LED.

  • e.g. Red + Green = Yellow Lighting
  • Red + Blue = Purple Lighting
  • Green + Blue = Cyan Blue Lighting

Firstly, choose and press one button from DIYl to DIY6 on the RF controller, for instance, the DIYl button. Secondly, press 1′ or ,J., button to increase
or decrease the ratio of red, green and blue on the LED, so as to create different lighting colors. Then the specific DIV color lighting will be saved on the DIYl button (the button you choose on the first step). Next time when you want to use this DIV color lighting, simply press DIYl button
for a quick access.

Installation

  1. How to cut the LED strip?
    Before cutting the LED strip, please keep these in mind.

  2. Once the strip is cut, an extra connector is needed for reconnection, otherwise the rest part being cut can not work. The connector is included in the package. You may contact the seller for the connector details.

  3. Double confirm the length for installation before making the cut.

  4. Cut the strip along the marks
    Ustellar-UT33360-RGB-EU-NF-LED-RGB-Light-Strip-09

  5. How to install the LED strip?

  6. Choose an even and smooth surface
    Ustellar-UT33360-RGB-EU-NF-LED-RGB-Light-Strip-10 Ustellar-UT33360-RGB-EU-NF-LED-RGB-Light-Strip-11

  7. Sweep the dust off the

  8. Tear the back sheet. surface.

  9. Pre:11 the strip with force.

Connect the light strip to controller cable, and then connect
controller cable to power adapter. Plug the adapter into the socket and tum on the light strip by pressing ‘ON’ button on the Rf remote controller.

Ustellar-UT33360-RGB-EU-NF-LED-RGB-Light-Strip-15

Note:

  1. If the strip can’t light up after the installation, please check whether the joints are connected correctly.
  2. Please make sure to tum off the power supply during routine maintenance.
  3. To avoid any damage to the strip, please do not use chemical solvent during routine maintenance.

How to control the light strip?

  1. Download the App Lotus Lantern by scanning the QR code below.
    This App is compatible with Android 4.0 and iOS 8.1 or above.
    Download APP

  2. Scan the QR code from the label or user manual
    Ustellar-UT33360-RGB-EU-NF-LED-RGB-Light-Strip-16
    The APP is compatible with Android 4.0 and 105 8.1 and higher version.

  3. Power on the light.

  4. Activate the Bluetooth function on your phone and open the App to automatically connect to the light.

  5. Enjoy the lighting by exploring the functions such as brightness, modes, music sync, timer etc. via the App.

Contact Us

Have some issue? No worries! Please reach us via these channels.
Our customer services team is more than happy to help.
www.ustellar.com support@ustellar.com

Manufacturer. Shenzhen Ustellar Technology Ltd.
(shenzhen shiyou shib.lo keji you xiangong si )
Address: Rm.201, A Bldg., No. A Qianhai 1st Rd., Shengang Cooperation Zone,
Qianhai, Shenzhen, CHINA518000

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals