baby trend PY74 MUV Custom Grow Nursery Center Playard Instruction Manual
- October 27, 2023
- baby trend
Table of Contents
PY74 MUV Custom Grow Nursery Center Playard
Instruction Manual
Read all instructions BEFORE assembly and USE of the product.
KEEP INSTRUCTIONS FOR FUTURE USE.
WARNING
Playard Warnings
WARNING: Failure to follow the instructions could result in serious injury
or death.
WARNING: INFANTS CAN SUFFOCATE:
-
In gaps between a mattress too small or too thick and product sides.
-
On soft bedding
NEVER add a mattress, pillow, comforter, or padding. Use only the mattress provided by Baby Trend®. -
The playard mattress/pad is specially designed to prevent suffocation. The Playard mattress/pad has a solid base, a certain length and width, and is less than one inch thick in order to meet safety standards. Using a thicker or a different sized mattress/pad may allow a child’s head to get between mattress/pad and the side of the playard causing suffocation.
-
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.
-
ALWAYS place child on back to sleep.
-
NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation.
-
NEVER use a water mattress with this product.
WARNING- STRANGULATION HAZARD:
WARNING: NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll
into space between pad and loose mesh side causing suffocation.
-
Strings can cause strangulation! DO NOT place items with a string around a child’s neck such as hood stringsor pacifier cords. DO NOT suspend strings over playard or attach strings to toys.
-
NEVER place the player near a window where cords from blinds or drapes can strangle a child.
-
A child can become entrapped and die when improvised netting or covers are placed on top of a player. Never add such items to confine the child in the player.
-
ALWAYS ensure the full-size bassinet is fully assembled on the played before using the following accessories: changing table and/or Rock-A-bye bassinet(s).
-
NEVER leave a child in the product with sides lowered. Be sure the sides are in raised and locked position whenever a child is in the product.
WARNING: See Playard floor and side rails for warning. -
The player, including side rails, must be fully erected prior to use.
-
Make sure latches are secure.
-
Discontinue use of the product when a child is able to climb out or has reached the height of 35 in. (890 mm), or 30lb. (14kg).
-
When a child is able to pull to a standing position, remove bumper pads, large toys, and other objects that could serve as steps for climbing out.
-
NEVER leave Rock-A-Bye bassinet in place when the child is in the player. Only one child can use the Playard/ Nursery Center at any time.
-
ALWAYS provide the supervision necessary for the continued safety of your child. When used for playing, never leave the child unattended. Children in cribs must be under supervision at all times.
-
ALWAYS ensure that the player, changing table, and the Rock-A-Bye bassinet are safe by checking regularly, before placing the child in it, and that every part is properly secured in place.
-
NEVER leave the Full-Size bassinet in place when a child is in the player.
-
NEVER leave Changing Table in place when a child is in the player.
-
Only one child can use the Playard/Nursery Center at any time.
-
NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend® Customer Service at 1-800-3287363 for replacement parts, repair, or instructions. NEVER substitute parts.
-
This product is not intended for commercial use.
PARTS
Check the parts listed below to make sure you have all the parts for this model before assembling the player.
ASSEMBLY
Additional Parts
Type may vary
IMPORTANT! To ensure the safe operation of your product, please follow
these instructions carefully.
Please keep these instructions for future reference.
IMPORTANT! Before assembly and each use, inspect this product for damaged
hardware, loose joints, missing parts, or sharp edges. NEVER use it if any
parts are missing or broken.
IMPORTANT! Adult assembly is required.
TO ASSEMBLE PLAYARD
ATTENTION:** Playard must be fully
assembled and securely locked before installing or using other accessories.
-
Unzip the bag and remove the Playard frame (Fig. 1). Undo the Fasten straps and set the Mattress aside.
DO NOT push the center down yet. -
Top rails must be fully erected before lowering the center. Pull up one rail at a time, hold one hand on each side of the rail and pull up sharply, do not pull from the middle where the center latch release is located, make sure both tubes latch in place and each rail is rigid (Fig. 2).
IMPORTANT: The center must be raised while locking the rails. If one rail will lock but the other side will not then, unlock the rail by squeezing the release in the center and try again.
-
Once all four (4) top rails are locked in place, push down on the center handle (Fig. 3a). The center mechanism automatically locks in place. IMPORTANT: Test each top rail by pushing down slightly to confirm each is rigid and securely in place before use (Fig. 3b). IMPORTANT: The handle located in the center of the Playard floor MUST remain raised (Approx. 45.7 cm or 18 inches) while locking the side rails in place.
If the center is not raised the rails will NOT lock. If you experience difficulty and one side of the rail will lock but the other side will not unlock the rail by squeezing the release in the center and trying again. -
Place the Mattress on the floor of the Playard with the padded side facing up (Fig. 4).
-
Insert the hook & loop fasteners located on the underside of the Mattress through the slots in the floor on each end of the Playard (Fig. 5a). Fasten the hook and loop fasteners to the underside of the Playard floor to prevent the Mattress from moving (Fig. 5b).
-
To operate the brakes on the Wheels, press downward on the brake levers. To release, lift upward on the lever (Fig. 6).
FOLDING PLAYARD
-
Release the hook and loop fastener holding the Mattress from underneath the Playard floor and set the mattress aside.
Do not unlock the top rails yet, the center of the floor must be raised before the top rails will unlock.
Rotate the center handle counter-clockwise 90 degrees and raise the center as high as the top rails (Fig. 7). Gather the Legs and Wheels together towards the center as close as possible so that they nearly touch.
-
Locate the rail latch release in the center and bottom side of each rail. Squeeze the lever with two hands until the rail releases the two tubes (Fig. 8a), then push down (Fig. 8b).
NOTE: If the top rail(s) do not release completely, DO NOT FORCE! Lift the center of the floor higher. Both tubes must be released for the top rail to fold.
-
Bring the four (4) corners and center tightly together (Fig. 9). Wrap the Mattress around the Playard frame with a padded side facing inward.
-
Secure the hook and loop fasteners by feeding them through the loops on the end of the Mattress and folding them back onto themselves (Fig. 10). Place folded Playard into the carry bag so that the handle comes through the opening between each side of the zipper.
ACCESSORIES
Full-Size Bassinet Warnings:
WARNING: Failure to follow these warnings and the instructions could
result in serious injury or death.
WARNING-FALL HAZARD: To help prevent falls, do not use this product when
the infant begins to push up on hands and knees or has reached a height of 25
in. (635 mm), the weight of 15 lb. (6.8 kg) or 3 months old, whichever comes
first.
• ALWAYS check that the bassinet is securely locked on the base/stand by
pulling upwards on the bassinet bed.
SUFFOCATION HAZARD
Infants have suffocated:
• In gaps between extra padding and the side of the bassinet, and
• On soft bedding
Use only the pad provided by Baby Trend®. NEVER add a pillow, comforter, or
another mattress for padding.
• Strings can cause strangulation! DO NOT place items with a string around a
child’s neck such as hood strings or pacifier cords. DO NOT suspend strings
over the bassinet or attach strings to toys.
• NEVER use plastic shipping bags or another plastic film as mattress covers
are not sold and are intended for that purpose. They can cause suffocation.
• Use a bassinet with only one child at a time.
• NEVER place a child under the Full-size bassinet.
• The bassinet must be fully assembled and installed before use.
• The players, including side rails, must be fully erected prior to use. Make
sure each latch is secure.
• NEVER leave the Full-size bassinet in place when a child is in the player.
• NEVER leave Changing Table in place when a child is in the player.
• Discontinue use of the full-size bassinet when the child begins to push up
on hands and knees or has reached the height of 25 in. (635 mm), the weight of
15 lb. (6.8 kg) or 3 months old, whichever comes first.
• Only one child can use the bassinet at any time.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their backs to sleep unless otherwise advised by their physician.
• ALWAYS place the child on their back to sleep.
• ALWAYS provide the supervision necessary for the continued safety of your
child. NEVER leave children unattended.
• If a sheet is used with the mattress/pad, use only the one provided by Baby
Trend® or one specifically designed to fit the dimension of the bassinet
mattress.
• ALWAYS provide the supervision necessary for the continued safety of your
child. NEVER leave children unattended.
• Child can become entrapped and die when improvised netting or covers are
placed on top of a player. Never add such items to confine the child in the
player.
TO ASSEMBLE THE FULL-SIZE BASSINET
Full- Size Bassinet with metal support tubes
ATTENTION: Playard must be fully assembled and securely locked before
installing or using the Full-size bassinet feature. (See To Assemble Playard
section). You will need to remove the mattress from the bottom of the Playard
to use inside your Full-size bassinet.
-
Connect opposing Mattress Support Tubes that are attached to the bottom of the Fullsize bassinet (Fig. 11a).
• Before placing the Mattress into the Full-size bassinet, make sure the Mattress Support tubes are connected as seen in (Fig. 11b).
-
Position the Full-size bassinet over and down into the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place (Fig. 12).
-
Place the mattress into the Full-size bassinet with the padded side facing upward (Fig. 13).
TO REMOVE THE FULL-SIZE BASSINET
• Remove all other accessories in use on the Fullsize bassinet. Remove the mattress from the Full-size bassinet. Disconnect opposing mattress support tubes. Unsnap all clips and lift the Full-size bassinet.
ACCESSORIES
Changing Table:
WARNING-FALL HAZARD: Children have suffered serious injuries after falling from changing tables. Falls can happen quickly.
• STAY within arm’s reach of your child.
• ALWAYS secure this product to the support frame by (manufacturer’s instructions for securing the changing unit/pad). See instructions.
SUFFOCATION HAZARD: Babies have suffocated while sleeping on changing tables. Changing tables are not designed for safe sleep.
• NEVER allow baby to sleep on changing table.
• NEVER leave the changing table in place when the child is in the bassinet or the player. Always remove the changing table while not in use. To prevent your child from falls and other injuries, always use the safety belt when children are on the changing table.
• Discontinue use of the changing table when the child begins to push up on hands and knees or has reached the height of 22 in. (558.8 mm), the weight of 15 lb. (6.8 kg) or 3 months old, whichever comes first.
• Do not use changing table if it is damaged or broken.
• ALWAYS use the restraint system. Adjust the belt as needed to get a snug fit.
ATTENTION: Playard and Full-size bassinet must be fully assembled and securely locked before installing or using the changing table feature (See To Assemble Playard and Full-size bassinet sections, pages 1-23). -
Lay the changing table cover on a flat surface with the backside facing up. Locate the 2 connector bars (Fig. 14a). Insert the connector bars into the backside of the changing table covering (Fig. 14b).
• Attach the short bars with the 2 connectors to the connector bars (Fig. 14c). Be sure the clips are faced up during this preparation on the backside of the changing table covering (Fig. 14d). Insert both ends with the push pins into the connector Bars. Ensure all pins click into position on all 4 connection points (Fig. 14e).
• Close the covering by using the hook and loop fasteners on the flap. Flip the flaps over the bars and fasten them together (Fig. 14f).
TO SECURE THE CHANGING TABLE TO THE PLAYARD
IMPORTANT! When the changing table is in the upper position the changing table must be secured to the player frame using the hook and loop fasteners provided. -
Locate the 4 clip fasteners on the bottom of the changing table (Fig. 15a). • To attach the changing table to the player, lower the changing table into the Full-size bassinet. Push down on the top and bottom clips of the changing table to secure the clips onto the Full-size bassinet railing (Fig. 15b). Secure the two snaps on the strap down onto the Playard (Fig. 15c).
NOTE: DO NOT use changing table on a player without the Full-size bassinet (See To Assemble Full-size bassinet section, page 21) and securing the clips to the player.
TO USE CHANGING TABLE RESTRAINT SYSTEM
-
Place the child on the changing table, and make sure hands and arms are clear of the restraint. Bring the restraint around the child’s waist and clip the male and female ends of the buckle together (Fig. 16a).
• Tighten the strap until it fits snugly around the child’s waist (Fig. 16b). DO NOT OVER-TIGHTEN.
• To remove, unsnap the buckle.
ATTENTION: NEVER use changing table if it is damaged or broken.
TO REMOVE CHANGING TABLE
-
Unsnap from the player (Fig. 17a). Locate all 4 clips/fasteners on the changing table. Pull up on all 4 clips to release them from the player frame (Fig. 17b).
ACCESSORIES
Warnings for Toy Accessories including Toybar/Mobile Canopy with toys
WARNING:
• Possible entanglement injury.
• Keep out of baby’s reach.
• Remove Toybar/Mobile/Canopy with toys when baby begins to push up on hands and knees. Recommended use from birth to 5 months.
• Toys are not intended to be mouthed by the baby and should be positioned clearly out of reach of the babyface and mouth.
• ALWAYS attach all provided fasteners (strings, straps, clamps, etc.) tightly to the player according to these instructions. Check frequently.
• Do not add additional strings or straps to attach to any other crib or playpen.
• The Toybar/Mobile/Canopy with toys is intended for visual stimulation and not to be grasped by the child.
ACCESSORIES
WARNINGS FOR REMOVABLE ROCK-A-BYE BASSINET
WARNING: Failure to follow these warnings and the instructions could result in serious injury or death.
FALL HAZARD: To prevent falls, stop using the product when infant:
• Begins to wiggle out of position or turn over in the product, head touches the upper edge of the product, reached the height of 25 in. (635 mm), the weight of 15 lb.(6.8 kg) (approximately 3 months of age).
• ALWAYS use a restraint system if a restraint system is provided with the product.
SUFFOCATION HAZARD
Infants have suffocated:
• In gaps between extra padding and sides of bassinet/cradle and
• On soft bedding
Use only the pad provided by the manufacturer.
NEVER add a pillow, comforter, or another mattress for padding.
• When trapped between product and adjacent surfaces.
• ONLY use ROCK-A-BYE BASSINET on the player when it is securely attached.
• If a sheet is used with the pad, use only the one provided by Baby Trend® or one specifically designed to fit the dimension of the ROCK-A-BYE BASSINET bassinet mattress.
• NEVER use ROCK-A-BYE BASSINET in a different product.
WARNING: NEVER leave the child unattended.
SUFFOCATION HAZARD: Infant carriers can roll over on soft surfaces and suffocate a child. NEVER place carriers on beds, sofas, or other soft surfaces.
FALL HAZARD: The child’s activity can move the carrier. NEVER place carriers on countertops, tables, or any other elevated surface.
NEVER use this carrier as a means to transport an infant in a motor vehicle. Infant carriers are not intended for use as infant restraint devices in motor vehicles.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep unless otherwise advised by their physician.
• FALL HAZARD – Always check that the Rock-A-Bye is securely locked on the base/stand by pulling upwards on the Rock-ABye bed.
• The player, including side rails, must be fully erected prior to use. MAKE SURE EACH LATCH IS SECURE.
• Strings can cause strangulation! NEVER place items with a string around a child’s neck such as hood strings or pacifier cords. NEVER suspend strings over the Rock-A-Bye bassinet or attach strings to toys.
WARNING: Possible entanglement injury with toys attached. Keep out of the baby’s reach.
• Do not use the Rock-A-Bye bassinet or place it on Playard when baby begins to push up on hands and knees.
• NEVER place the product near a window where cords from blinds or drapes can strangle a child.
• Always provide the supervision necessary for the continued safety of your child. NEVER leave child unattended.
• NEVER use plastic shipping bags or another plastic film as mattress covers are not sold and are intended for that purpose. They can cause suffocation.
• Use a Rock-A-Bye bassinet with only one child at a time.
• DO NOT use a large bassinet when using Portable Rock-A-Bye Bassinet.
• NEVER place a child under the Rock-A-Bye bassinet.
• NEVER store the Rock-A-Bye bassinet in the player while in use.
• The large bassinet must be fully assembled and installed before use.
• To help prevent heat build-up inside the player and to avoid overheating your child, when using the Rock-A-Bye Bassinet NEVER use an outdoor canopy.
• NEVER leave Portable Rock-A-Bye Bassinet in place when a child is in the player. Only one child can use the Playard at any time.
• ALWAYS ensure that the player, changing table, and Portable Rock-A-Bye Bassinet are safe by checking regularly, before placing the child in it, that every part is properly and securely in place.
• NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair, or instructions. NEVER substitute parts.
TO ASSEMBLE A REMOVABLE ROCK-A-BYE BASSINET
ATTENTION: Playard and full-size bassinet must be fully assembled and securely locked before installing or using the Rocka-bye bassinet (s) feature. (See To Assemble Playard and full-size bassinet sections, pages 1-23). -
Pull the removable bassinet fabric back to access the bottom of the removable bassinet. Use the handles to pull the frame supports into the support locks (Fig 18a). • Make sure the frame supports click and are seated firmly in the support locks (Fig 18b). NOTE: Use ONLY the handles to move Frame supports. Using your fingers may result in getting pinched.
-
Pull the fabric over the frame and secure the fabric with buttons on the sides and front of the frame (Fig. 19).
-
Use the hook and loop fasteners provided to fix the mattress into the removable bassinet (Fig. 20). DO NOT use the removable bassinet without the provided mattress.
-
To raise the handle, push both buttons on each side of the handle with your fingers while pulling it forward (Fig. 21a). • To lower the handle, push both buttons on each side of the handle with your fingers while pushing the handle backward (Fig. 21b).
-
To use the removable bassinet in the Playard, lower it into the player (Fig. 22a). Push down on the front and rear of the removable bassinet to secure the hooks onto the Playard railing. Button the front and rear straps from the removable bassinet onto the Playard frame (Fig. 22b).
NOTE: DO NOT use the removable bassinet on Playard without securing the hooks and straps to the player.
ROCKER
FUNCTION
-
Turn the removable bassinet over and pull the rocker feet from the base (Fig. 23a). Set the removable bassinet on a flat surface (Fig. 23b).
NEVER use the removable bassinet on a raised surface such as a Table, Bed, or Chair. A fall can occur.
Reverse steps 18
through 21 to remove the Rock-Abye bassinet (s) feature.
PARENT ORGANIZER ASSEMBLY
-
Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it snaps into place (Fig. 24a). Diaper Stacker: Skip to step 24b.
• Connect the Parent Organizer/Diaper Stacker to the player by pressing the two (2) connecting clips over the top rail of one of the player’s longer sides (Fig. 24b).
NOTE: When using the full-size bassinet, clip the Parent Organizer/Diaper Stacker clips directly onto the large full-size bassinet clips.
MUSIC CENTER
WARNING: Keep batteries out
of children’s reach. Old and new batteries should not be mixed. Alkaline,
standard carbon-zinc and rechargeable batteries should not be mixed. Remove
batteries before storing the music center for a long period of time. -
The Music Center is designed to be attached to the long rail of the player/napper (Fig. 25). MUSIC OPERATION
-
The Music Center requires 4 AA batteries. Please see Figure 26 for battery installation. Unscrew the battery door screws and pull them outward on the battery door. Install batteries as shown. Re-install the battery door and secure it with screws.
MUSIC| | To listen to MUSIC, press the MUSIC button. Press the button to change the song.
---|---|---
NATURE SOUNDS| | To listen to NATURE sounds, press the NATURE button. Press the button to change the sound.
SLEEP MUSIC| | To listen to SLEEP music, press the SLEEP button. Press the button to change the song.
VOLUME CONTROL| | VOLUME: Use the 2 buttons to control the unit’s volume.
VIBRATION| | VIBRATION: To use the VIBRATION, press down
VIBRATION button once to activate the speed, press it again for faster speed. Press it again to reduce the speed.
NIGHT LIGHT| | NIGHT LIGHT: To use the night light, press the NIGHT LIGHT button.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
BABY TREND® CUSTOMER SERVICE
The Customer Service Department can be contacted at 1 (800) 328-7363 Monday
through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations
are required prior to returning product(s) to Baby Trend®.
WARRANTY
DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR
REPLACEMENT PARTS, SERVICE, AND REPAIR.
The Baby Trend® warranty covers workmanship defects within 1 year of purchase.
Any product which has been subjected to misuse, abuse, abnormal use, excessive
wear and tear, improper assembly, negligence, environmental exposure,
alteration, or accident, or has had its serial number altered or removed
invalidates all claims against the manufacturer. Any damage to property during
installation is the sole responsibility of
the end user. The Customer Service Department can be contacted at 1 (800)
328-7363 Monday through
Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are
required prior to returning product(s) to Baby Trend®. Please visit
http://babytrend.com/pages/ limited-warranty for complete warranty details.
Baby Trend, Inc.
13048 Valley Blvd.
Fontana CA 92335
1-800-328-7363
(8:00am ~ 4:30pm PST)
www.babytrend.com
Copyright © 2017, Baby Trend Inc., All Rights Reserved.
Todos Los Derechos Reservados.
References
- Limited Warranty Coverage – Baby Trend
- Baby Trend® | Car Seats, Strollers, High Chairs, Nursery and More!