baby trend 011724 Morph Single to Double Modular Stroller Travel System Instruction Manual

baby trend 011724 Morph Single to Double Modular Stroller Travel System

Product Information

Specifications

• Product Name: Morph Single to Double Modular Travel System with EZ-LiftTM PLUS infant car seat
• Manufacturer: Baby Trend, Inc.
• Address: 13048 Valley Blvd. Fontana CA 92335
• Contact: 1-800-328-7363 (8:00 am ~ 4:30 pm PST)
• Website: www.babytrend.com
• Model Number: TS11xxxA

Frequently Asked Questions

• Q: What is the maximum weight and height limit for the stroller?
  • A: The stroller accommodates a maximum weight of 50 pounds (22.67 kg) per child and is suitable for children up to 40 inches (102 cm) tall.
• Q: Can I use the stroller with more than two children?
  • A: No, the stroller is designed to accommodate a maximum of two children to prevent hazardous conditions.
• Q: What should I do if I find damaged parts during inspection?
  • A: Contact our customer service department for repair or replacement parts to ensure safe operation of the stroller.

WARRANTY

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within 1 year of purchase. Any product which has been subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration or accident, or has had its serial number altered or removed invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user.

Customer Service Department can be contacted at 1 800-328-7363 Monday through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®. Please visit http://babytrend.com/pages/limited-warranty for complete warranty details.

Baby Trend, Inc

• 13048 Valley Blvd. Fontana CA 92335
• 1-800-328-7363
• (8:00am ~ 4:30pm PST)
• www.babytrend.com

Precautions

• WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference.
• WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out, always use the safety harness and insure that the children are properly positioned according to these instructions.
• WARNING: Wheel can detach and cause tip over. Pull on the wheel to assure it is securely attached.
• WARNING: Care must be taken when folding and unfolding the stroller to prevent finger entrapment.
• WARNING: Child may slip into leg openings and strangle. NEVER use in full recline position unless the seat is in full recline and footrest buckle released.

Stroller accommodates 2 children max. Do not exceed.

• The Front / Rear Stroller Seat is designed for a child who is at least 6 months and is not over 40 inches (102 cm) tall. Max. weight 50 pounds (22.67 kg) each. Use of the stroller with (2) children weighing more than 50 pounds (22.67 kg) each will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition.
• The rear stand on platform and jump/rear seat are designed for a child who is at least 2 1/2 years old and is not over 40 inches (102 cm) tall. Children totaling more than 100 pounds (45.35 kg), will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition to exist.
• Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of the stroller and cause a hazardous, unstable condition. Adding an extra parcel bag or parcel rack will render the stroller unstable.
• ONLY the seat comes with this travel system can be used on the frame.
• The maximum weight that can be carried in the storage basket is 5 pounds (2.27kg).
• The maximum weight that can be carried in the cup holder is 1 pound (0.45kg).
• The maximum weight that can be carried in the parent phone holder is 1 pound (0.45kg).
• Be certain the stroller is completely opened and locked in place before allowing a child near the stroller.
• The maximum weight for the infant car seat is 30lb (13.6kg).
• NEVER leave child unattended.
• NEVER use the stroller on stairways or escalators.
• NEVER use the stroller with roller skates, in-line skates, skateboards or bicycles.
• NEVER allow your stroller to be used as a toy.
• To clean use only mild household soap or detergent and warm water on a sponge or clean cloth.
• Check your stroller for loose screws, worn parts, torn material or stitching on a regular basis. Replace or repair parts as needed.
• Discontinue use of stroller should it malfunction or become damaged. Please contact our customer service department to arrange for repair or obtain replacement parts.

IMPORTANT

• To ensure safe operation of your stroller, please follow these instructions carefully. Please keep these instructions for future reference.
• Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any parts are missing or broken.
• Adult assembly is required. Keep child away during unpacking and assembly.
• When using two car seats or any dual seating combination, make sure to first put the child in the REAR seat, and then the FRONT seat. When removing child, start in the FRONT seat first, then remove the child from the REAR seat.
• For use of two car seats or any dual seating combination, both seats must have weight in them. Always sit the 2 children at the same time.

What In The Box

Check that you have all the parts for this model before assembling the stroller.

SET UP THE STROLLER FRAME

Unlock

• Unlock the fold latch (Fig. 1a) and unfold stroller frame by pulling upward on the stroller handle until the frame locks (Fig. 1b).

WHEELS AND BRAKES

FRONT WHEELS

• Lean the stroller backwards and push each front wheel assembly into the front wheel housing until they lock into place (Fig. 2).

REAR WHEELS

• Press the rear wheel posts into the rear frame hub until it clicks into place (Fig. 3).
  • NOTE: Pull on the rear wheel assembly to ensure that it is securely attached to the stroller.

REAR BRAKES

WARNING

• Always set brakes when the stroller is not being pushed so that the stroller will not roll away.
• NEVER leave stroller unattended on a hill or incline as the stroller may slide down the hill.

Engage and Release

• Press down the brake levers to engage and lift up on the brake levers to release. The stroller may require forward or rearward movement in order to engage the brake. Check that the brakes are properly applied (Fig. 4).

HOLDERS, HANDLE COVER AND BASKET INSTRUCTIONS

PARENT PHONE HOLDER

WARNING

The maximum weight that can be carried in the parent phone holder is 1 pound (0.45kg).

• Slide the clip on the phone tab located on the stroller handle until it’s tightly secured (Fig. 5).
• To release, simply pull the parent phone holder upwards.

CUP HOLDER

WARNING: To avoid burns, never put hot liquids in a cup holder. Avoid possible tipping, do not place more than 1lb. (0.45kg) in a cup holder.

• Slide the clip on the cup holder over the cup holder tab on the handle bar.
• Push until firmly in place (Fig. 6).

STROLLER HANDLE COVER FEATURE

• Removal
  • Unzip to remove (Fig. 7a).
• To Attach
  • Wrap around the handle and zip closed (Fig. 7b).

NOTE

• May be stored in the storage basket.

STORAGE BASKET

Check all attachments

• If received unattached, follow below instructions to attach:
• Ensure that all straps and snap closures are attached correctly.
  • NOTE: Always secure the snaps shown in (Fig. 8a).
• Ensure the zipper for the basket is secured (Fig. 8b) and the straps near the rear wheels (Fig. 8c).

STROLLER POSITIONS

Stroller Modular Towers

IMPORTANT

• For any accessory that is placed at the lowest position, the stroller towers MUST be in an upright position.

To Use Front Modular Towers

• At the front of the stroller frame, locate the 2 stroller modular towers (Fig. 9a).
• Lift and rotate the tower to the upright locked position (Fig. 9b).
• Repeat for the other side.

Hideaway

• To put away, rotate the tower down to its storage locked position (Fig. 9c). Repeat for the other side.

STROLLER MODULAR ADAPTERS

IMPORTANT

For any accessory that is placed at the highest or middle position, the stroller adapters MUST be installed at the same height level on the stroller frame.

• To Install
  • Insert the adapter onto the stroller frame as shown until it clicks and locks in (Fig. 10a).
  • Repeat for the other side.
• Example
  • See (Fig. 11e) for an example for installing an accessory.
• Removal
  • Press the button and lift the adapter up simultaneously (Fig. 10b). Repeat for the other side.

ASSEMBLING THE TODDLER SEAT AND BUMPER BAR

ASSEMBLING THE TODDLER SEAT

• Unfold the toddler seat fully (Fig. 11a).
• To assemble the toddler seat, unzip the zipper fully, located underneath the seat (Fig. 11b).
• Unwrap the fabric from the tube (Fig. 11c). (1) Push the lower tubes into the inner slot of the seat frame. (2) Ensure the push pin clicks into place on both sides. Then wrap the fabric back, and zip the zipper around the sea frame.

If received unattached, follow below instructions to attach:

• Feed the strap through the tab to anchor the seat fabric on the seat frame, ensure the toddler seat is secured (Fig. 11d). Repeat for the other side.
• Ensure the stroller adapters are positioned on the middle position. See step 10 for installation.
• Attach the seat by lining up the seat anchors on the side of the seat with the anchors on the stroller frame and pushing them together until they click securely (Fig. 11e). The seat can face in either direction, frontward or backward.

Carriage Mode

• Make sure the buckle strap underneath the seat is unbuckled.
• Then loosen the recline seat strap by squeezing the adjuster and pulling downwards (Fig. 11f). The carriage should be fully extended before using.

NOTE

• The footrest area should be unbuckled (Fig. 11g).

BUMPER BAR HANDLE COVE

• To attach: Before attaching the bumper bar to the stroller, wrap the handle cover around the bar (Fig. 12a).

BUMPER BAR

• WARNING: Do not use bumper bar to lift or carry seat with child inside. The bumper bar is not a carrying handle.
• WARNING: FALL HAZARD: Bumper bar is not designed to support a car seat, stroller may become unstable.
• Attach the bumper bar by lining up anchors with the slots on the seat.
• Push until it locks into place (Fig. 13a). NOTE: The bumper bar must be securely attached before using this product.
• To detach the bumper bar, press the release button on the bottom of the bar on each side, and pull bar out of the anchors (Fig. 13b).

TO ADJUST SEAT AND REMOVABLE CANOPY

TO ADJUST SEAT

WARNING

The upright position should be used only for a child that is at least 6 months old.

• Toddler Seat Mode: The seat can be adjusted into an upright, reclined position.
• Push the center button on both sides of the stroller adapter to rotate the seat (Fig. 14a).
• Rotate the seat into the desired position until it clicks into place (Fig. 14b). The seat can face in either direction, frontward or backward.
• Buckle the strap located underneath the seat (Fig. 14c). To tighten the strap, use the hook and loop method through the clip. Pull the strap firmly and attach.
• To adjust the recline seat strap, squeeze the adjuster while pulling downwards or upwards (Fig. 14d).
  • NOTE: There are 6 positions for the legrest.
• Press on both sides to unlock, adjust to desired position and release the buttons to lock into position (Fig. 14e).

REMOVABLE CANOPY

• To attach the removable canopy: Slide the canopy clips on the inside of the corresponding slots on the stroller frame (Fig. 15a).
• Pull over the back of the canopy fabric to connect the three attachments located on the top of the seat frame (Fig. 15b).
• To open the canopy: Push forward on the front edge of the canopy while holding the rear of canopy in place (Fig. 15c).
• To fold the canopy: Pull backwards on the front edge (Fig. 15d).
• To remove the canopy: Press inward on both canopy tabs and slide the canopy up to remove (Fig. 15e).

TO SECURE THE CHILD

• WARNING: Avoid serious injury from falling or sliding out. Always use the safety harness.
• STRANGULATION HAZARD: Child can strangle in loose straps. Never leave child in seat when straps are loose or undone.

Type 1

The shoulder straps of the 5-point harness have 3 attachment positions. Select the position that places the shoulder strap level with, or below the top of the child’s shoulder (Fig. 16a). To adjust harness height unhook the shoulder strap from the crotch buckle. Feed the shoulder strap through the harness spread slots. You can access these slots from the rear of the seat underneath the fabric. Feed shoulder strap through the appropriate slot and reattach the shoulder strap to the crotch buckle.

Carefully place the child in the stroller seat and bring the safety harness around the child’s waist and over the child’s shoulders. Place the crotch strap between the child’s legs. Insert the male end of each shoulder/waist belt into the buckle on the crotch strap. Tighten the harness so it is snug around the child’s waist and over the child’s shoulders (Fig. 16b).

TO RELEASE THE CHILD

Type 1

• To release, push the button on center clasp and the two harness buckles will pop free (Fig. 16c).
• Unhook the shoulder straps only if adjusting the harness positions (Fig. 16d).

DETACH THE SEAT

NOTE: The stroller can be folded with or without the seat attached.

• Push the lower buttons on each side of the seat to disengage from the stroller frame (Fig. 17).
• DO NOT detach with child in the stroller seat.

THE INFANT CARSEAT

WARNING: Avoid serious injury from falling or sliding out, always use the Infant Car Seat harness.

CS01 EZ-Lift, CS02 EZ-Lift PLUS and CS03 EZ-Lift PRO Infant Car Seats

Refer to step 10 to install the 2 stroller modular adapters.

Align the car seat module to the stroller modular adapters. Latch the module into the stroller frame. Underneath the car seats handle hub, carefully align it to the modular towers of the stroller frame. Press down firmly for the click. ALWAYS ensure that the car seat is properly connected and locked onto the stroller before each use by lifting up on the car seat handle (Fig. 18a).

Removing the car seat:

• Set handle to the carry position (Fig. 18b). Squeeze the release handle located at the Top-rear of the car seat and lift away from the stroller (Fig. 18c).
• Fold away the stroller towers when not in use (See Fig. 9c).

USING THE REAR JUMP SEAT AND PLATFORM

USING THE REAR JUMP SEAT

WARNING: The rear platform and jump seat are designed to accommodate a child who is at least 2 1/2 years old, has good balance and coordination, and is not over 40 inches tall.

• Have the child sit on the jump seat facing backwards. Secure the child with the jump seat 3-point harness (Fig. 19a).
• Put the seat belt around the child’s waist, and buckle to the crotch strap (Fig. 19b). Adjust the seat belt to be snug around the child’s waist.
• TO RELEASE! Push the button on the center clasp and all the harness straps will release (Fig. 19c).

IMPORTANT

• When the child is sitting on the rear jump seat, please remove the adapter from the highest position and place them into the middle position or put them into the storage basket.

USING THE PLATFORM

_ WARNING: _The rear platform and jump seat are designed to accommodate a child who is at least 2 1/2 years old, has good balance and coordination, and is not over 40 inches tall.

IMPORTANT:  Before using the platform, remove any accessory if placed on the highest position.

• First engage the rear brakes (Fig. 20a). Place child in rearfacing standing position.
  • NOTE: Ensure the child holds the frame with both hands at all times. See (Fig. 20b) where the child can hold the stroller frame.
• Position the child on the platform on the back of the stroller. Be sure child is standing facing forward and hands are holding frame. Be sure that the child’s feet are fully on the platform at all times.

IMPORTANT

• When the child is standing on the rear platform, please remove the adapter from the highest position and place them into the middle position or put them into the storage basket.

WARNING:  These are the ONLY approved use modes. Failure to follow these instructions could result in serious injury or death.

IMPORTANT

• When using two car seats or any dual seating combination, make sure to first put the child in the REAR seat, and then the FRONT seat. When removing child, start in the FRONT seat first, then remove the child from the REAR seat.
• For use of two car seats or any dual seating combination, both seats must have weight in them. Always sit the 2 children at the same time.

SINGULAR RIDING POSITIONS

Single – 6 Modes

• 1. Toddler Seat – Middle Position – Forward Facing
• 2. Toddler Seat – Middle Position – Rear Facing
• 3. Carriage – Middle Position – Forward Facing
• 4. Carriage – Middle Position – Rear Facing
• 5. Car Seat – Middle Position – Forward Facing
• 6. Car Seat – Middle Position – Rear Facing

DOUBLE RIDING POSITIONS

Toddler & Car Seat – 5 Modes

• 7. Toddler Seat – Low Position – Forward Facing, Car Seat – High Position – Rear Facing
• 8. Toddler Seat – Low Position – Rear Facing, Car Seat – High Position – Rear Facing
• 9. Toddler Seat – Low Position – Rear Facing, Car Seat – High Position – Forward Facing
• 10. Toddler Seat – High Position – Rear Facing, Car Seat – Low Position – Rear Facing
• 11. Toddler Seat – High Position – Rear Facing, Car Seat – Low Position – Forward Facing

Carriage & Car Seat – 4 Modes

• 12. Carriage – Low Position – Rear Facing, Car Seat – High Position – Rear Facing
• 13. Carriage – Low Position – Rear Facing, Car Seat – High Position – Forward Facing
• 14. Carriage – High Position – Rear Facing, Car Seat – Low Position – Rear Facing
• 15. Carriage – High Position – Forward Facing, Car Seat – Low Position – Rear Facing

Toddler Seat with Bench, Stand Board – 4 Modes

• 16. Toddler Seat – Low Position – Forward Facing, Child on Bench
• 17. Toddler Seat – Low Position – Forward Facing, Child on Stand Board
• 18. Toddler Seat – Low Position – Rear Facing, Child on Bench
• 19. Toddler Seat – Low Position – Rear Facing, Child on Stand Board

Car Seat with Bench, Stand Board – 4 Modes

• 20. Car Seat – Low Position – Forward Facing, Child on Bench
• 21. Car Seat – Low Position – Forward Facing, Child on Stand Board
• 22. Car Seat – Low Position – Rear Facing, Child on Bench
• 23. Car Seat – Low Position – Rear Facing, Child on Stand Board

Carriage with Bench, Stand Board – 4 Modes

• 24. Carriage – Low Position – Forward Facing, Child on Bench
• 25. Carriage – Low Position – Forward Facing, Child on Stand Board
• 26. Carriage – Low Position – Rear Facing, Child on Bench
• 27. Carriage – Low Position – Rear Facing, Child on Stand Board

TO FOLD STROLLER

WARNING

• Care must be taken when folding and unfolding the stroller to prevent finger entrapment.
• Care must be taken when folding stroller to prevent damage. Make sure all accessories, mobile phones, diaper bags or purses are removed before folding. Failure to remove items in, or on the stroller so may result in damage to the stroller or the item(s) if not removed. Baby Trend® will not be liable or warrant any damage.

CAUTION: Do not allow children near stroller while folding.

• Ensure the stroller towers are properly closed (See Fig. 9c).
• OPTIONAL: The stroller can be folded with the (1) Toddler Seat Mode facing forward in the highest position (2) OR without the seat installed (see Fig. 21b).
• DO NOT remove the seat while child is inside.

Stroller – Fold Latch

• To fold the stroller, pull the stroller back to position, the front wheel forward facing and engage the brakes.
• (1) Push both buttons while (2) lifting up both triggers on the frame (Fig. 21a). Push down on the stroller handle until the stroller is completely folded.
• Compress stroller and secure with fold latch (Fig. 21b).

MAINTENANCE

FRONT AND REAR WHEEL RELEASE

If adjustment or replacement is necessary:

• If replacing the front wheel:
• • Press the pin located behind the wheel hub. Pull the wheel out from the hub (Fig. 22a).
• If replacing the rear wheel:
  • Press the release pin to disconnect (Fig. 22b). Repeat for the other side.

SEAT PAD

• To clean the seat pad, use only mild household soap or detergent and warm water on a sponge or clean cloth.

OTHER

• Check your stroller for loose screws, worn parts, torn material or stitching on a regular basis. Replace or repair parts as needed.

CUSTOMER SERVICE

BABY TREND® CUSTOMER SERVICE

The Customer Service Department can be contacted at 1 800-328-7363 Monday through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®.

Baby Trend, Inc.

• 13048 Valley Blvd. Fontana CA 92335
• 1-800-328-7363
• (8:00 a.m. ~ 4:30 p.m. PST)
• www.babytrend.com

Copyright © 2024, Baby Trend Inc., All Rights Reserved.

References

• Limited Warranty Coverage – Baby Trend
• Baby Trend® | Car Seats, Strollers, High Chairs, Nursery and More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>