TYPES LM58259 Single Beam Smart LED FOG Light User Guide
- June 4, 2024
- TypeS
Table of Contents
SMART LED FOG LIGHT
SINGLE BEAM
WP ITM. LM58259
Care & Use Instructions
Important, retain for future reference: Read
carefully
Package Includes
2 x Ultra Bright Fog Light LEDs
1 x Smart Hub
4 x Cable Ties
2 x 9006 Mounting Rings
2 x 9005 Mounting Rings (Pre-installed)
1 x 3M VHB for Smart Hub
Specifications
- 4 x Ultra Bright LEDs
- 4 x 3030 1.5W RGBs
- Operation voltage: 12V (Controller operation voltage: 12V only)
- Operation temperature: -40°F to 194°F (-40 °C to 90 °C)
- Current: 2.3A@12V
- Color temperature: 6,500 K ± 510 K
- Lumen (Maximum):- Single Beam: 1,800 LM ± 15%
- Cable length with plug: 3.9 inches (10cm)
- Cable length from LED lamp to the connector: 0.5m
- Cable length from connector to the controller: 1.5m
- Cable length from the controller to hardwire: 1m
Installation
Installation Steps by Fog Light Type
Review the vehicle’s owner’s manual or service manual to reference how to
access your light bulbs.
The interchange of the 9005 / 9006 mounting ring for LM58259: The interchange
needs to be done using a screwdriver.
i. Remove the 9005 blue rubber ring.
ii. Unscrew and pull out the 9005 mounting ring.
iii. Insert the 9006 mounting ring and tighten the screw.
iv. Insert the 9006 blue rubber ring. 9005/9006
- Remove the headlight dust cover.
- Insert the Fog Light body.
- Rotate clockwise to secure.
- Connect the plug to the Fog Light connector.
- Put the dust cover back.
- Turn on the Fog Light, and make sure it is lighted and the direction of the beam is correct.
NOTE: There are some cases when the LM58259 (9005/9006) will not turn on
after plugging in. It is because they may not be universal for every
make/model of vehicle. Often times the positive and negative terminals are in
the opposite side. When you come across this situation, please follow these
steps:
- Flip the plug halfway around and plug it into the Fog Lightconnector. Turn on the headlights and check if the light is on.
- Put a cable tie, or a piece of electrical tape to hold the connector securely, since the notch is no longer locked onto the clips.
• Some vehicles require the engine to be started for the operation of all beams. If the LED light does not turn on then rotate the plug and try again.
• The headlight dust covers of some vehicles may not be put back successfully after the Fog Lights are installed. Look for the correct third-party dust covers as a replacement.
• This Fog Light fits exclusively to 12V vehicle input.
• When fetching and installing the Fog Lights, DO NOT touch the LED chips with your fingers to avoid injury.
• Try to not block or obstruct air flow of the cooling fan.
• Before installing, please make sure the Fog Lights are free from damage, fracture, and no impurities on the LED chip.
• For additional installation and product information, visit typesauto.com.
Smart Hub Installation
a. Connecting the LED to the Smart Hub. Make sure the 4-pin connectors are
securely fastened and route cables away from engine. The connectors are
directional, make sure to connect to the correction position and fasten each
end of the cap.
b. Secure the Smart Hub away from the car engine or any moving components.
Make sure to avoid placing the Smart Hub or cables near any extremely HOT
location or next to the car engine. Use double-sided tape to secure to any
flat location and use Cable Ties to tie all wiring away from all moving
components.
c. Smart Hub hardwire cables are color-coded, RED for POSITIVE (+) and BLACK
for NEGATIVE (-). Connect the RED cable to the POSITIVE (+) battery clamp. The
POSITIVE battery post will be slightly larger than the NEGATIVE post and will
be marked with a PLUS (+) sign. There may also be a RED protective cover over
the positive battery post. Connect the BLACK cable to the NEGATIVE (-) battery
clamp. The NEGATIVE will be marked with a MINUS (-) sign. There may also be a
BLACK plastic
the protective cover over the negative battery post.
NOTE: After connecting the Smart Hub to the car battery, the LED power
indicator will flash Blue. If the LED power indicator does not flash once
connected, please double-check your power connections.
The Smart Hub has built-in voltage protection to prevent car battery from
draining in case the lights are accidentally left on. The lights will be
turned off automatically and the Smart Hub will be on standby mode when the
voltage drops to approximately 12V. Once on standby mode, if the car battery
is producing below 12V, do not turn on the LED lights until your next engine
start or when the power is back to 12V or above.
APP Installation
Install the TYPE S LED APP on your smart device. Scan below QR code or search for the TYPE S LED APP in the APP Store or Google Play. Once installed, open the APP and begin enjoying your TYPE S LED Fog Light!
https://itunes.apple.com/us/app/type-s/id958525286?mt=8
Compatible with iPhone 4s & higher, iPad3, iPad Mini, iPad Air & higher, and iPod touch 5th Generation & higher. Requires iOS 9.0 or higher.
https://itunes.apple.com/us/app/type-s/id958525286?mt=8
Compatible with phones with Android TM 4.3 or higher.
Note: not all AndroidTM phones are equipped with Bluetooth ® v4.2
required for this application.
Using the APP
Tap “Smart Exterior Kit” icon to start APP will automatically connect to the Smart Hub when both are powered on (including Bluetooth) and within 30ft.
A. Master On/Off Switch
B. Password: You can set up a password to prevent other devices from
controlling your light. Once you have entered your password, it will be saved
in the APP and the Smart Hub Controller
Note: To set or change the password, your device must be connected to the
Smart Hub and simply follow the on-screen instructions. Changing the password
without connecting to the Smart Hub may cause an invalid password the next
time your APP and Smart Hub are activated. If you forget your password, simply
reset by pressing the Smart Hub Controller to reset button for 5 seconds or
disconnect the power from the car battery.
C.LED Zone Functions: Zone On/Off: press each zone icon to turn the LED
On or Off
Move Zone Icon: Press and hold the zone icon, and select “Move” to position
each zone icon at your desired location.
Rename Zone Icon: Press and hold the zone icon, and select “Rename” to rename
each icon. (Note: Maximum 4 characters)
Select Multiple: You can select and control multiple zones at once. Press and
hold the zone icon, select “Select Multiple” then select your desired zones by
pressing “Confirm”. To ungroup your selection, press and hold the zone icon
and select “Ungroup”
D: Save Preset: You can save your favorite settings. After creating your
setting, press “Save Preset” and enter your preset name. You can save up to 10
preset settings.
Select Preset: You can select your previously saved preset setting, press
“Select Preset” and choose your saved setting.
Delete Saved Preset Setting: To delete a saved preset setting, press
“Select Preset” and press and hold the preset setting that you wish to delete.
Press “Yes” to delete.
Select Color: Choose from up to 49 different colors. Press “Select
Color”, select your desired color and press “Confirm”.
E. LED Mode: Choose up to 7 different modes including preset color
themes.
Note: Music Mode allows music to control the lighting tempo through your
smartphone or tablet. Sync lighting with your music in two ways: 1.)
Through locally downloaded music files, or 2.) Through an enabled microphone
on the smartphone/tablet.
F. Brightness Slide bar to adjust the brightness setting.
G. Speed Slide bar to adjust the speed of the movement from each LED mode.
Important Safety Instructions:
- SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for LED Fog Light model LM58259.
- NEVER use the APP while operating your vehicle. Use the APP when the vehicle is stationary only.
- Before using this LED Fog Light, read all instructions and cautionary markings to ensure the product is properly & safely installed.
- Do not expose LED Fog Light to rain, moisture, or snow.
- Use of an attachment not recommended or sold by the LED Fog Light manufacturer may result in a risk of fire, electric shock, or injury to persons.
- Do not operate with a damaged cord.
- Do not disassemble LED Fog Light; take it to a qualified serviceperson when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
- To reduce risk of electric shock, disconnect all power before attempting any maintenance or cleaning. Turning off the lights will not reduce this risk.
WARNING: Do not install or use the product if it, in any way, impairs the safe operation of your vehicle. Follow the manufacturer’s instructions to ensure the product is properly & safely installed. Neither the manufacturer nor the reseller can be held responsible or liable for consequential, incidental, or indirect damages to either person or property resulting from the installation or improper use of this product. Check your state, provincial, or local laws before installing. This product is not DOT-approved.
Warnings
- Caution! If you get an error code, or lights are flickering, use a decoder to complete the installation. The decoder is sold separately.
- Considering the high intensity of light, DO NOT stare at the light when it is switched on.
- The surface of the LED will reach a very high temperature when it is turned on. DO NOT touch the surface directly to avoid severe burns.
- Before changing the original Fog Lights, make sure it is turned off and cooled.
- Keep LED chips of the Fog Lights free of dust, oil.
- Do not install or use the product if it, in any way, impairs the safe operation of your vehicle.
- Check your state or provincial laws before installing. The vehicle owner must comply with all applicable laws.
- This product is intended solely for Off-road / Fog light purposes.
- Manufacturer and Seller assume no liability for installation or use, which are solely the responsibility of the purchaser.
- This product is not DOT approved and is designed and intended for Off-road/Fog light uses only.
- Do not install or use the product if it, in any way, impairs the safe operation of your vehicle. Not for use in extreme temperatures.
- The manufacturer and seller are not responsible or liable for consequential, incidental, or indirect damages, whether to person or property, resulting from the installation or improper use of this product.
FCC Compliance Statement:
This device comply with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications or changes to this
equipment. Such modifications or changes could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
Class B digital devices, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help. The
device has been evaluated to meet the general RF exposure requirements.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
WARNING: This product can expose you to chemicals including DEHP and
DINP, which are known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov. The Bluetooth ® word
mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Winplus Co. Ltd is under license. Other trademarks and
trade names are those of their respective owners. 3M VHB TM is a trademark of
3M company. Smart LED Fog Light Single Beam LM58259
Responsible Party: TYPE S
2975 Red Hill Ave., Ste. 100, Costa Mesa,
CA 92626, U.S.A.
Tel: 1.866.294.9244
A Horizon Brands Company
2975 Red Hill Ave., Ste. 100, Costa Mesa,
CA 92626, U.S.A.
1.866.294.9244 | info@typesauto.com
©2021 TYPE S. All rights reserved.
www.typesauto.com
CONNECT WITH US @TypeSAuto
Made in China ML-58259_V1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>