ATEN CE820 USB HDMI HDBaseT 2.0 KVM Extender User Guide
- June 5, 2024
- Aten
Table of Contents
ATEN CE820 USB HDMI HDBaseT 2.0 KVM Extender
Package Contents
- 1 CE820L USB HDMI HDBaseT 2.0 KVM Extender (Local Unit)
- 1 CE820R USB HDMI HDBaseT 2.0 KVM Extender (Remote Unit)
- 1 HDMI KVM cable set
- 2 power adapters
Support and Documentation Notice
All information, documentation, fi rmware, software utilities, and specifi
cations contained in this package are subject to change without prior notifi
cation by the manufacturer.
To reduce the environmental impact of our products, ATEN documentation and
software can be found online at http://www.aten.com/download/
Technical Support
www.aten.com/support
Scan for more information
ATEN Website
|
User Manual
---|---
Hardware Overview
RS-232 serial port
link LED
power LED
power jack
HDBaseT out
Ethernet port (not applicable)
HDMI in
USB Type-B port
audio out
audio in
long reach mode and fi rmware upgrade switches
RS-232 serial port
wake up PC pushbutton
video out LED
link LED
power LED
power jack
HDBaseT in
Ethernet port (not applicable)
HDMI out
USB Type-A ports
audio out
audio in
long reach mode and fi rmware upgrade switches
Installation
Connect the audio plugs of the supplied KVM cable set to the audio input and
audio output ports on the CE820L. Plug the other end of the cable into the
audio input and audio output ports on the local computer.
Connect the USB connector of the supplied KVM cable set to the USB Type-B port
on the CE820L. Plug the other end of the cable into a USB Type-A port on the
local computer.
Connect the HDMI connector of the supplied KVM cable set to the HDMI input
port on the CE820L. Plug the other end of the cable into the HDMI port on the
local computer.
Plug one end of an Ethernet cable into the HDBaseT output port on the CE820L,
and the other into the HDBaseT input port on the CE820R.
Plug one of the supplied power adapters into a power source; then plug the
adapter’s power cable into the CE820L’s power jack.
Use an HDMI cable to connect the HDMI output port on the CE820R to your
monitor.
Plug the USB devices (mouse, keyboard, etc.), into their respective USB ports
on the CE820R.
Plug the microphone and speakers, into their respective audio ports on the
CE820R.
Plug the second power (supplied with this package) into a power source; then
plug the adapter’s power cable into the CE820R’s power jack.
To use the wake up PC pushbutton, connect the RS-232 serial port on the CE820L
to the local computer.
To control the local computer with a serial device, connect the RS-232 serial
port on the CE820L to the local computer as illustrated in step 10, and
connect a hardware / software controller to the RS-232 serial port on the
CE820R.
If you want to extend the video up to 150 m with 1080p resolution, put the
long reach mode switch to ON.
Rack Mount
For convenience and fl exibility, the CE820 can be mounted on system racks. To rack mount a unit, do the following:
- Using the screws provided in the mounting kits, screw the mounting bracket into the top or bottom of the unit.
- Screw the bracket into any convenient location on the rack.
Note: Rack screws are not provided. We recommend that you use M5 Phillips recessed screws.
LED Display and System Status
| LED | LED Display | System Status |
|---|---|---|
| Power | Lights green | The system is receiving power. |
| Lights orange | The connection between the CE820L and CE820R is stable. | |
| Off | The connection between the CE820L and CE820R is off. | |
| Flashes orange | The HDBaseT signal transmission is unstable | |
| Video Out | Lights orange | The video display is normal and secured with HDCP. |
| Flashes orange | The video display is normal but not secured with HDCP | |
| Off | The video is not displayed. |
Note: The Video Out LED is only available on the CE820R.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>