Astera FP5-E27 NYX Bulb User Manual

June 5, 2024
ASTERA

NYX BULB
Users Manua
MODEL NO: 
FP5-E27 (EU) / FP5-E26 (US/MIC) /FP5-B22
MANUAL VERSION: 1.2 — DATE OF ISSUE: 25/08/2020Astera FP5 E27 NYX
Bulb -

CONTENTS

  1. NYX Bulb
  2. USB DC
  3. Users Manual

PRODUCT OVERVIEW

Astera FP5 E27 NYX Bulb - 1

THE NYX BULB: USING

  1. Control options
    On/Off, static color via “blue mode”, Reset settings| On/Off, Static Colors, Preprogrammed E¥ects
    ---|---
    | All settings, Complex e¥ects, Talkback+, Updates
    | Control from DMX consoles via CRMX or W-DMX

  2. Switching On/OffAstera FP5 E27 NYX Bulb - 5

  3. Pairing - > AsteraApp
    Turn the NYX Bulb into „blue mode“ by holding down the power button for 3 secondsAstera FP5 E27 NYX Bulb - 6

  4. Static Colors
    Turn NYX Bulb into „blue mode“ by holding down the power button for 3 seconds. Press the button shortly to cycle between 13 predefined colors and white tones. To latch chosen color, hold the button until the blinking stops.

  5. Reset and Link to a CRMX transmitterAstera FP5 E27 NYX Bulb - 7

RESET to unpair and set Control Input to auto-detection mode

INTRODUCTION / INTENDED USE

The Astera NYX Bulb FP5 is a professional 1-pixel RGB+Amber+Mint LED illuminant with ultra-high TLCI/ CRI and calibrated color rendering as well as Astera‘s flicker free PWM technology.
Built-in CRMX, Bluetooth, and RF Modules provide the same connectivity known from other Astera fixtures. Numerous professional features and mounting options make the NYX Bulb a versatile light source for the Film, Broadcast, and Event industries, and decorative purposes.
It can be powered by AC from an E26/ E27/B22 socket as well as by wide range DC from e.g. a USB Powerbank or the optionally available battery-powered Astera PowerStation.
This device was designed for indoor and outdoor use – outdoor only with plugged-in rubber on the DC socket.
Do not shake the device. Avoid brute force when installing or operating the device.
When choosing the installation spot, please make sure that the device is not exposed to extreme heat or dust.
There should not be any cables lying around. You endanger your own and the safety of others!
The ambient temperature must be set. Keep away from direct insulation (particularly in cars) and heaters.
Never use the device during thunderstorms connected to a power socket. Over voltage could destroy the device. Always disconnect the device during thunderstorms.
Make sure that the area below the installation place is blocked when rigging, derigging, or servicing the fixture.
Always fix the fixture with an appropriate safety bond.
The specified ambient temperature must be maintained
Operate the device only after having become familiarized with its functions.
The device is not dimmable. Use Astera PowerStation or AsteraApp for dimming.
Please use the transportation cases or original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
If this device will be operated in any way different from the one described in this manual, the product may suffer damages and the guarantee becomes void.
Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, crash, etc.

SAFETY INFORMATION

Before you operate this unit read the manual carefully. Always make sure to include the manual if you pass/ rent/ sell the unit to another user.
Keep in mind that this manual cannot address all possible dangers and environments. Please use your own caution when operating.
This product is for professional use only. It is not for household use.

  • Do not operate the unit in areas of high-temperature conditions or under direct sunlight.
  • It will cause an abnormal function or damage the product.
  • Make sure the unit is mounted properly and safely.
  • Always follow local safety requirements.
  • Please note that the mechanical stability of certain lamps and lamp holders may be altered and contact and hold may be impaired if the newly inserted lamp is heavier than the original lamp.
  • Suitable for damp locations
  • Do not use with standard dimmers
  • Do not open the product housing.
  • Do not apply power if the light is damaged.
  • Do not submerge the light into any liquid.
  • Do not replace the LED light source.
  • Caution, risk of electric shock.

The NYX Bulb and its power supply shall be installed near the socket outlet which shall be easily accessible.
Warning electric shock: risk of – Do not open power unit, for indoor use only.
The exterior surfaces of the light can become hot, up to 70°C (158°F) during normal operation.

  • Ensure that accidental physical contact with the device is impossible.
  • install only in ventilated locations.
  • Do not cover the light.
  • Allow all lights to cool before touching.
  • Keep 0.3m (12in) from objects to be illuminated.

CLEANING AND MAINTAINING

Caution: Liquids entering the housing of the device can cause a short circuit and damage the electronics. Do not use any cleaning agents or solvents.

TROUBLESHOOTING

Problem Possible cause Solution
The fixture does not turn on The fixture maybe does not connect to the power

Connect it to an E26/E27 socket, PowerStation, or power bank to try again
The fixture turns on but the LEDs do not emit light| The fixture could be set to BLACKOUT mode| Set to display black color or is operating in DMX mode and doesn’t receive a valid signal. It is good practice to do a RESET SETTINGS
The fixture is not working correctly – it does not display the color or effect
chosen| The fixture may still be operating under a
previous setting| It is good practice to do a RESET SETTINGS between setups

SPECIFICATIONS – TECHNICAL DATA

Item Code FP5-E27 (EU) / FP5-E26 (US/MIC) /FP5-B22 (GB)
Colors RGBMintAmber
Total LED Power / Power Draw 14W / 10W
Luminous Flux* 7501m (@4000K)
CRI(RA)/TLCI 3200-6500K* 196
Strobe 0 – 25 Hz
AC Power input E27/B22 100-240VAC, 50/60Hz, ta:40°C
AC Power input E26 100-120VAC, 50/60Hz, ta:40°C
DC Power input 5-18VDC, 2.1A via DC socket
Wired DMX No
CRMX Receiver Built-in
Dimensions (mm / inches) 070 x 130 / 0276 x 5.12
Ingress Protection IP44: connected via AC + Rubber plug-in DC socket

IP20: connected via DC socket

*Typical value

MANUFACTURER DECLARATION
Hereby, Astera LED Technology GmbH declares that the type of radio equipment NYX Bulb FP5-E27 complies with Directive 2014/53 / EU. The full text of the EU Declaration of Conformity is available at the following Internet address: https://astera-led.com/Downloads/DoC/DoCNYXBulb.pdf
FP5 -E26: Astera LED Technology GmbH declares that this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o¥ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

  • Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment.
  • This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
    (1) This device may not cause harmful interference, and
    (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC RF
Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Astera LED-Technology GmbH
Stahlgruberring 36
81829 Munich
Germany
info@astera-led.com | www.astera- led.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals