ASTERA FP3-BTB Hyperion Tube BTB User Manual
- June 10, 2024
- ASTERA
Table of Contents
- CONTENT
- PRODUCT OVERVIEW
- USAGE
- More control options
- Switching On/Of
- Connect BTB
- Connect AsteraBox as BTB
- Connect light as BTB
- Pair with lights
- Linking to a CRMX transmitter
- Reset
- Charging
- Rigging
- Tube Holder
- Optional available mounting accessories
- WingPlate
- CrossPlate
- INTRODUCTION / INTENDED USE
- SAFETY INFORMATION
- CLEANING AND MAINTAINING
- SECONDARY SAFETY MOUNTING
- TROUBLESHOOTING
- MANUFACTURER DECLARATION
- SPECIFICATIONS – TECHNICAL DATA
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
**ASTERA FP3-BTB Hyperion Tube BTB User Manual
**
NOTE
Bluetooth Bridge built-in with this logo
CONTENT
- Hyperion Tube BTB (FP3-BTB)
- 2x Eye Bolt (FP1-EBLT)
- 2x Tube Holder (AX1-H)
- Silicon Cap (FP1-SP)
- Users Manual
PRODUCT OVERVIEW
Back
Side view
Top view
USAGE
Integrated control panel
Use the menu buttons to navigate through the main menu. Settings for color adjustment and brightness / runtime are directly accessible by two symbol buttons.
Top navigation | Inside Main Menu |
---|
On/Off
Main Menu| Back to previous menu
Reset Settings| Scroll down
Change Input Select| Scroll up
Set DMX Adress| Choose
Color adjustment
Brightness and runtime control
More control options
On/Off, Static Colors, Preprogrammed Effects.
All settings, Complex effects, Talkback+, Updates.
Control from DMX consoles via CRMX or Wireless DMX.
Control from DMX consoles via Data Link and Power/Data Combination Cable.
Switching On/Of
-
ON
-
OFF
A new Hyperion Tube BTB needs a few seconds of charge to disable its shipping mode before it can be switched on.
Connect BTB
To control your lights with the Astera App, first connect a Bluetooth Bridge (BTB). It forwards the Astera App signal to paired lights. You may use an Astera Box as BTB or choose a light with built-in BTB, like AX9, NYX Bulb, Pixel Brick, Hyperion Tube BTB, Titan Tube BTB.
Connect AsteraBox as BTB
Please power on the AsteraBox. Connect the AsteraBox directly from the steraApp main menu by following the instructions there.
Connect light as BTB
Please note: This ONLY works for Astera lights with built-in Bluetooth.
For all other Astera lights, please use an AsteraBox as BTB.
Please power on the light. Hold down the power button for 3 seconds until the
light flashes blue. In the AsteraApp press „Manage Bluetooth Bridges“, then
“+” and follow instructions on screen to connect. The light which is connected
as BTB shows a small blue Bluetooth Icon next to the lamp icon in the app.
-
Hyperion Tube BTB
-
AsteraApp
-
AsteraApp
To disable the BTB again press UNBOND BLUETOOTH in the AsteraApp.
Pair with lights
Power on the light. Then hold down the power button for 3 seconds until the light flashes blue. Go to “Pair with Lights” dialog in the AsteraApp. Then press OK.
-
Hyperion Tube BTB
-
AsteraApp
Linking to a CRMX transmitter
-
Hyperion Tube BTB
-
Hyperion Tube BTB
-
Hyperion Tube BTB
-
AsteraBox
-
Hyperion Tube BTB
Reset
RESET to unlink CRMX and unbond Bluetooth. Sets „Input Select“ to „AUTO“ and
runtime to 5h.
Charging
While the power cable is connected, the display shows the charging status. Charge immediately when the battery is empty. Do not store the unit when the battery is empty. Charging time is approximately 3 hours.
Rigging
The Hyperion Tube BTB can be hung via a M5 eyebolt or two TubeHolders. The TubeHolders have a 1/4“ -20UNC thread and two M5 threads for attaching mounting accessories or SafetyEyebolts. Only use the TubeHolder with the SafetySplint.
When hanging a Hyperion Tube BTB via its eyebolt, make sure to use a secondary
safety spot (e.g. via AX1-H). Make sure the light cannot drop more than 20cm
if primary mounting fails.
Tube Holder
(AX1-H)
Optional available mounting accessories
Baby pin
(AX1-BLT)
(sold seperatly)
WingPlate
(AX1-WP)
(sold seperatly)
A mounting holder for 2 AX1 holders (AX1-H) with backside 1/4”-20 thread for AX1 double-ended spigot (AX1-BLT). Can be used to hang or mount tubes and create shapes such as triangles and squares out of multiple tubes.
CrossPlate
(AX1-CP)
(sold seperatly)
Up to 4 WingPlates can be mounted onto one CrossPlate so Tubes can be mounted in parallel to create a 4-Bank. To hold the additional weight the Cross Plate has a 5/8” Babypin welded onto its backside. NOTE: The CrossPlate needs WingPlates (AX1-WP) that are supplied separately.
INTRODUCTION / INTENDED USE
The Hyperion Tube BTB from ASTERA is a LED tubelight for professional use in the event and film business. The Hyperion Tube BTB is designed for direct or indirect illumination of objects or sceneries. Due to its built-in battery it can be quickly set up at places where traditional lights cannot be mounted easily. The Hyperion Tube BTB has the Titan LED Engine and offers excellent color and light values. The Hyperion Tube BTB generates white or colored light and the color temperature can be adjusted in many ways. The Hyperion Tube BTB can be controlled with the AsteraApp or with wired DMX or wireless CRMX. The device can also be controlled by the integrated display or by infrared remote control.
The Hyperion Tube BTB can be used in multiple ways, including hanging. For this purpose, the device is equiped with M5 threads on both sides. The Hyperion Tube BTB can be used indoors and outdoors and has an IP65 rating (only with SiliconCap (FP1-SP) on DC socket).
Do not shake the device. Avoid brute force when installing or operating the
device.
When choosing the installation spot, please make sure that the device is not
exposed to extreme heat or dust. Avoid direct sunlight for a longer period of
time. The specified ambient temperature must be maintained. Keep away from
direct insulation (particularly in cars) and heaters. Never use the device
during thunderstorms connected to the power mains. Overvoltage could destroy
the device. Always disconnect the device during thunderstorms. Make sure that
the area below the installation place is blocked when rigging, derigging or
servicing the fixture. Always fix the fixture with an appropriate safety wire.
Operate the device only after having become familiarized with its functions
Please consider that unauthorized modifications on the device are not allowed due to safety reasons! If this device will be operated in any way different to the one described in this manual, the product may suffer damages and voids the warranty. The disclaimer includes all damages, liability or injury resulting from failure to follow the instructions in this manual. Furthermore, any other operation may lead to dangers lke shortcircuit, burns, electric shock, crash etc. This device is not for household use and is not suitable for permanent installation.
SAFETY INFORMATION
Before you operate this unit read the manual carefully. Always make sure to
include the manual if you pass/ rent/ sell the unit to another user. Please
use your own caution when operating.
This product is for professional use only. It is not for household use.
-
Do not operate the unit in areas of high temperature conditions or under direct sunlight. It may cause abnormal behavior or damage the product.
-
Always use a suitable safety wire when mounting the light overhead.
-
Connect the safety wire only to the intended safety mount.
-
Always follow local safety requirements.
-
Only authorized personal may service the battery.
-
Do not place in fire or heat.
-
Do not use or charge the light if it is damaged.
-
Avoid bumping or plunging, it may cause fire or explosion.
-
Never store the battery when fully drained. Always recharge immediately when empty. Please do not charge unattended.
-
Make sure to fully charge all units before storing them.
-
Partially charged batteries will lose capacity.
-
Fully recharge every 6 months if not used.
-
The battery may only be replaced with an original spare part from Astera.
-
It is recommended to charge at a temperature between 15°C and 35°C.
Warning: In extreme cases, abuse or misuse of standard/rechargeable batteries can lead to: -
Explosion
-
Fire development
-
Heat generation or smoke and gas development.
-
Do not directly look into the light.
-
lt can cause harm to your eyes.
-
Do not look at the LEDs with a magnifying glass or any other optical instrument that may concentrate the light output.
-
Use only Astera approved accessories to diffuse or modify the light beam.
-
Do not open the product housing.
-
Do not apply power if the light is damaged.
-
Do not submerge the light into any liquid.
-
Do not replace the LED light source.
-
Caution, risk of electric shock.
The Hyperion Tube BTB shall be installed near the socket-outlet which shall be easily accessible. Warning: risk of electric shock – Do not open device.
-
The exterior surfaces of the light can become hot, up to 70°C
(158°F) during normal operation. -
Ensure that accidental physical contact with the device is impossible.
-
lnstall only in ventilated locations.
-
Do not cover the light.
-
Allow all lights to cool before touching.
-
Keep 0.3m (12in) from objects to be illuminated
CLEANING AND MAINTAINING
Caution: Liquids entering the housing of the device can cause a short circuit and damage the electronics. Do not use any cleaning agents or solvents. Only clean using a soft damp cloth.
SECONDARY SAFETY MOUNTING
The Hyperion Tube BTB must always be secured by a safety wire when used in a hanging position. If the primary suspension fails, the device must not fall more than 20cm.
Use Eyebolts and M5 threads on the sides. Please check the safety regulations in your region.
TROUBLESHOOTING
Problem | Possible cause | Solution |
---|---|---|
The fixture does not turn on. | The battery may be empty. | Connect it to the AC |
and try again.
The fixture turns on and the display is on, but the LEDs do not emit light.|
The fixture could be set to BLACKOUT mode. Set to display black color or is
opera- ting in DMX mode and doesn’t receive a valid signal.| It is good
practice to do a RESET SETTINGS.
The fixture is not wor- king correctly – it does not display the color or
effect chosen.| The fixture may still be operating under a previous setting.|
It is good practice to do a RESET SETTINGS between setups.
The power cable is connected but the fixture is not charging.| The battery may
be fully charged.| The fixture will only commence charging when its battery
has a temperature of 45° C or less. Turn the fixture off and let it cool down;
once cold enough, it will start charging.
DISPOSAL
- The light contains a lithium ion battery.
- Don‘t throw the unit into the garbage at the end of its lifetime.
- Make sure to dispose is according to your local ordinances and/or regulations, to avoid polluting the environment!
- The packaging is recyclable and can be disposed.
MANUFACTURER DECLARATION
Hereby, Astera LED Technology GmbH declares that the type of radio equipment Hyperion Tube BTB complies with Directive 2014/53 / EU. The full text of the EU Declaration of Conformity is available at the following Internet address: https://astera-led.com/hyperion.
Astera LED Technology GmbH declares that this equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
deter-mined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
FCC Caution:
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons
SPECIFICATIONS – TECHNICAL DATA
Order Code | FP3-BTB |
---|---|
LED Engine | Titan LED Engine |
Colors | RGBMintAmber |
Total LED Power | 144 W |
LED Power Draw | 92 W |
Light Output 4000K* | 5800 lm, 1570 lx @ 1m |
CRI(Ra) / TLCI 3200-6500k* | ≥96 |
Beam Angle / Field Angle | 135° x 115° / 175° x 160° |
Strobe | 0 – 25Hz |
Pixel | 32 |
Battery Runtime | up to 20 hours |
Battery Lifetime | 70 % after 300 cycles |
Charging Time (nominal) | 3 hours |
DC Input | 24 V, 4 A |
Wired DMX | Yes |
CRMX Receiver | Built-in |
BluetoothBridge (BTB) | Built-in |
Wireless Frequencies | CRMX, UHF, Bluetooth, Wifi |
Range | CRMX / UHF up to 300 m / 330 ydsBluetooth up to 3 m / 3,3 yds |
Housing Material | Polycarbonate, metal end caps |
IP Rating | IP65 (only with FP1-SP) |
Ambient Temperature | 0 – 40 °C / 32 – 104 °F |
Weight | 2.9 kg / 6.39 lbs |
Dimensions | Ø43 x 2031 mm / Ø1.7” x H79.9” |
References
- LED Commercial Lighting and Lighting Controls | Current - GLI Brands
- Wireless LED Lighting Film & Event by Astera
- Twice the length of Titan Tube by Astera
- Twice the length of Titan Tube by Astera
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>