ASTERA AX2 Wireless LED Bar User Manual
- June 10, 2024
- ASTERA
Table of Contents
- PRODUCT OVERVIEW
- AX2: USAGE
- RF CHARACTERISTICS
- HANGING OF THE AX2
- CONNECTING SEVERAL AX2 WITH BARCONNECT
- INTRODUCTION / INTENDED USE
- SAFETY INFORMATION
- CLEANING AND MAINTAINING
- SECONDARY PROTECTION
- TROUBLESHOOTING
- DISPOSAL
- MANUFACTURER DECLARATION
- SPECIFICATIONS – TECHNICAL DATA
- Documents / Resources
User Manual AX2 Wireless LED Bar
PRODUCT OVERVIEW
Bottom
- AX2-50 or AX2-100
- 2x Feet
- 2x Track Hanger
- Power on True1 Cable
- Users Manual
Oblique view
AX2: USAGE
- Integrated control panel
Use the menu buttons to navigate through the main menu.
| Top navigation| Inside Main Menu
---|---|---
| On/Off
| Main Menu| Back to previous menu
| Reset Settings| Scroll down
| Change Input Select| Scroll up
| Set DMX Address| Choose/Confirm
| Color adjustment
| Brightness and runtime control
| Address several connected AX2
More Control options
On/Off, Static Colors, Preprogrammed Effects
All settings, Complex effects, Talkback+, Updates
Control from DMX consoles via CRMX or W-DMX
Control from DMX consoles via XLR 5P Cable
Switching On/Off
A new AX2 needs a few seconds of charge to disable its shipping mode
3. Pairing - > AsteraApp
Turn the AX2 into „blue mode“ by holding down the power button for 3 seconds
and then tap „pair with Lights“ in the Satrap.
4. Linking lamp to a CRMX transmitter
RESET to unpair and set „Input Select“ to auto detection mode
6. Charging
While the power cable is connected, the display shows the charging status.
Charge immediately when the battery is empty. Do not store the unit when the
battery is empty. Charging time is approximately 5 hours.
RF CHARACTERISTICS
Wireless| EU: UHF***
(863-870MHz)| USA: UHF
(917-922.20MHz)| AUS: UHF
(922.30-927.50MHz)| SGP: UHF
(920.50-924.50MHz)
---|---|---|---|---
Modulation| FHSS| FHSS| FHSS| FHSS
ERP Transmitter)| <25mW| <25mW| <25mW| <25mW
Channel Count| 47| 53| 53| 41
Wireless| KOR: UHF
(9179-921.5MHz)| RUS: UHF
(86875-869.12MHz)| JPN: UHF
(922.80-926.40MHz)| CRMX
(2402-2480MHz)
---|---|---|---|---
Modulation| FHSS| FHSS| FHSS| FHSS
ERP (Transmitter)| <25mW| <25mW| <25mW| <100mW
Channel Count| 10| 6| 19| 79
Wireless Modules| Bluetooth 5.0 LE (2402-2480MHz)
---|---
Modulation| FHSS
ERP (Transmitter)| 10mW (BLE)
Channel Count| 40
HANGING OF THE AX2
The Airline tracks at back and bottom of the AX2-50/-100 housing are used to attach optionally available mounting fittings. The AX2-50/-100 can be mounted using TrackPoint (AX-TP) and Super clamps/Grip Heads or hung up using the Track Hangers (AX-TH) or Fly Bar (AX2-FB) for vertical position. When hanging, secure with a safety wire. This should be attached to the safety hooks at the back of the AX2-50/100 housing. Make sure the light cannot drop more that 20cm if primary mounting fails. Bar Connect+ (Integrated fasteners and counterparts) at both ends of the housing click into place and make a form- fitting locked connection when arranging multiple units in a line. When hanging vertical, it is permitted to join a maximum amount of 4 units of AX2-50 or 4 units of AX2-100 together in a line (Notice: mounted at least at every 2nd connection point).
With Fly Bar
With Track Hanger
Permitted way hanging
Permitted way hanging
CONNECTING SEVERAL AX2 WITH BARCONNECT
Quickly merge several Pixel Bars while maintaining the pixel pitch.
Aim connected units together to maintain consistent lighting or hang them. The
integrated IR modules enable auto-addressing for Aster App and DMX
control.
INTRODUCTION / INTENDED USE
The AX2-50 / AX2-100 from ASTERA is a LED wall washer for professional use in the event and film business. The AX2 is designed for direct or indirect illumination of objects. Due to its built-in battery it can be quickly set up and at places where traditional lights cannot be mounted easily. Like the ASTERA Tubes, the AX2 has the Titan LED Engine and offers excellent color and light values. The AX2 generates white or colored light and the color temperature can be adjusted in many ways. Both AX2 models can be controlled with the Aster App or with wired DMX or wireless CRMX. The device can also be controlled by the integrated display or by infrared remote control. The AX2 can be used standing or hanging. For this purpose, the device is equipped with airline tracks to attach the appropriate mounting accessories. Furthermore, several AX2 can be easily connected with the integrated Bar Connect+. The AX2 can be used indoors and outdoors and has an IP65 rating.
Do not shake the device. Avoid brute force when installing or operating the
device.
When choosing the installation-spot, please make sure that the device is not
exposed to extreme heat or dust. Avoid direct sunlight for a longer period of
time.
The ambient temperature must be set. Keep away from direct insulation
(particularly in cars) and heaters.
Never use the device during thunderstorms connected to the power mains. Over
voltage could destroy the device. Always disconnect the device during
thunderstorms.
Make sure that the area below the installation place is blocked when rigging,
derigging or servicing the fixture.
Always fix the fixture with an appropriate safety wire.
Operate the device only after having become familiarized with its functions.
Please consider that unauthorized modifications on the device are forbidden
due to safety reasons!
If this device will be operated in any way different to the one described in
this manual, the product may suffer damages and the guarantee becomes void.
Furthermore, any other operation may lead to dangers like short-circuit,
burns, electric shock, crash etc.
This device is not for household use and is not suitable for permanent
installation.
SAFETY INFORMATION
Before you operate this unit read the manual carefully. Always make sure to
include the manual if you pass/ rent/ sell the unit to another user.
Keep in mind that this manual cannot address all possible dangers and
environments. Please use your own caution when operating.
This product is for professional use only. It is not for household use.
-
Do not operate the unit in areas of high temperature conditions or under direct sunlight. It will cause abnormal function or damage the product.
-
Always use a suitable safety wire when mounting the light overhead.
-
Connect the safety wire only to the intended safety mount.
-
Always follow local safety requirements.
-
Only authorized personal may service the battery.
-
Do not place in fire or heat.
-
Do not use or charge the light if it is damaged.
-
Avoid bumping or plunging, it may cause fire or explosion.
-
Never store the battery when fully drained. Always recharge immediately when empty. Please do not charge unattended.
-
Make sure to fully charge all units before storing them.
-
Partially charged batteries will lose capacity.
-
Fully recharge every 6 months if not used.
-
The battery may only be replaced with an original spare part from Aster.
-
It is recommended to charge at a temperature between 15°C and 35°C
Warning: In extreme cases, abuse or misuse of standard/rechargeable batteries can lead to: -
Explosion
-
Fire development
-
Heat generation or Smoke and gas development.
Do not directly look into the light.
- lit can cause harm to your eyes.
- Do not look at the LEDs with a magnifying glass or any other optical instrument that may concentrate the light output.
- Use only Aster approved accessories to diffuse or modify the light beam.
- Do not open the product housing.
- Do not apply power if the light is damaged.
- Do not submerge the light into any liquid.
- Do not replace the LED light source.
- Caution, risk of electric shock.
The AX2 shall be installed near the socket-outlet which shall be easily
accessible.
Warning: risk of electric shock – Do not open device.
The exterior surfaces of the light can become hot, up to 70°C (158°F) during
normal operation.
- Ensure that accidental physical contact with the device is impossible.
- install only in ventilated locations.
- Do not cover the light.
- Allow all lights to cool before touching.
- Keep 0.3m (12in) from objects to be illuminated.
CLEANING AND MAINTAINING
Caution: Liquids entering the housing of the device can cause a short circuit and damage the electronics. Do not use any cleaning agents or solvents.
SECONDARY PROTECTION
The AX2-50/-100 Pixel Bar must always be secured by a safety wire when used in a hanging position. If the primary suspension fails, the device must not fall more than 20cm.
Use
Safety rigging point.
Please check the safety regulations in your region.
TROUBLESHOOTING
Problem | Possible cause | Solution |
---|---|---|
The fixture does not turn on | The battery may be empty | Connect it to the AC |
and try again
The fixture turns on and the display is on, but the LEDs do not emit light|
The fixture could be set to BLACKOUT mode| Set to display black color or is
operating in DMX mode and doesn’t receive a valid signal. It is good practice
to do a RESET SETTINGS
The fixture is not working correctly – it does not display the color or effect
chosen| The fixture may still be operating under a previous setting| It is
good practice to do a RESET SETTINGS between setups
The power cable is connected but the fixture is not charging| The battery may
be fully charged| The fixture will only commence charging when its battery has
a temperature of 45° C or less. Turn the fixture off and let it cool down;
once cold enough, it will start charging
DISPOSAL
**** The light contains a lithium ion battery.
- Don‘t throw the unit into the garbage at the end of its lifetime.
- Make sure to dispose is according to your local ordinances and/or regulations, to avoid polluting the environment!
- The packaging is recyclable and can be disposed.
MANUFACTURER DECLARATION
Hereby, Aster LED Technology GmbH declares that the type of radio equipment
Pixel Bar AX2-50/-100 complies with Directive 2014/53 / EU. The full text of
the EU Declaration of Conformity is available at the following Internet
address: https://astera-led.com/ax2
Aster LED Technology GmbH declares that this equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC RF
Radiation Exposure Statement Caution:
To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.
SPECIFICATIONS – TECHNICAL DATA
Order Code | AX2-50 / -100 |
---|---|
Colors | RGBMintAmber |
Total LED Power | 80W / 160W |
Power Draw | 40W / 80W |
Light output – 2700k, 3200k,5500k (50)* | 1800lm, 2230lm, 2265lm |
Light output – 2700k, 3200k,5500k (100)* | 3600lm, 4460lm, 4530lm |
CRI(RA)/TLCI 3200-6500k* | ≥96 |
Beam Angle | 21° |
Strobe | 0 – 25Hz |
Pixels | 16-Aug |
Battery Lifetime | 70 % after 300 cycles |
Battery Runtime | up to 20 hours |
Charging Time (nominal) | 5 hrs |
Input Voltage | 110 – 240V, 50/60 Hz |
Input Current | 0.7A/115VAC ~ 1.0A/230VAC |
Range | 300 m / 330 yds. |
Wired DMX | Ye s |
CRMX Receiver | Built in |
Wireless Frequencies | CRMX 2.4GHz, UHF |
Housing | Aluminium |
IP Rating | IP65 |
Operating Temperature | 0° – 40° C / 32° – 104° F |
Weight | 4.5kg/9.9lbs / 7.9 kg/17.5 lbs |
Dimensions with hook (mm/inches) | 520 x 165 x 65 / 20.5 x 6,5 x 2,6 1020 x 165 |
x 65 / 40.1 x 6,5 x 2,6
Dimensions without hook (mm/inches)| 500 x 165 x 65 / 19.7 x 6.5 x 2.6 1000 x
165 x 65 / 39.4 x 6.5 x 2.6
Aster LED Technology GmbH
Stahlgruberring 36
81829 Munich
Germany
info@astera-led.com | www.astera-
led.com
https://qrco.de/astera_ax2
ORDER CODES:
AX2-50 AND AX2-100
MANUAL VERSION: 1.0
DATE OF ISSUE: 10/30/2020
Documents / Resources
|
ASTERA AX2 Wireless LED
Bar
[pdf] User Manual
AX2 Wireless LED Bar, AX2, Wireless LED Bar, LED Bar, Bar
---|---
References
- LED Commercial Lighting and Lighting Controls | Current - GLI Brands
- Wireless LED Lighting Film & Event by Astera
- Wireless LED Bar by Astera
- Wireless LED Bar by Astera
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>