FALCON RIDGE KAW-3010-FC03 Mule 3010 & 4010 Full Cab Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
KAW-3010-FC03 Mule 3010 & 4010 Full Cab
Instruction Manual
KAW-3010-FC03 Mule 3010 & 4010 Full Cab
2515 Bypass Road Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of 3010 Full Cab Enclosure
With Lexan Windshield
KAW-3010-FC03
Notice: Do not smoke inside the cab or expose the enclosure to direct
flames. The cab is Flammable.
-
Be sure to read these instructions thoroughly before unrolling and installing the 3010 Full Cab Enclosure. The installation is best done when the temperature is 65 degrees F. or warmer.
-
Carefully unroll the Cab Enclosure on a large flat surface that is clean and free of dirt or other material that may soil or scratch the windows of the Cab.
-
Check over the parts included in the carton with the parts list shown below:
Velcro Hook strips:| 2 each| 5” long
---|---|---
“ “| 8 each| 6” long
“ “| 2 each| 7” long
“ “| 1 each| 36” long
Snap studs| 9 each (1 extra)|
Cab Enclosure| 1 each| -
Loosely drape the Cab Enclosure over the Mule roll cage. Begin in the rear of the cab and place the 36” adhesive Velcro strip on the bar running behind the seat back centered. Pull the rear window down and attach the Velcro along the bottom of the window here.
-
Now move to the front of the cab and pull down so the top of the cab fits snugly to the top of the roll cage. Working down the front of the doors, place the two 6” and one 8” adhesive Velcro tabs on the roll cage to match up with the tabs sewn to the cab enclosure.
-
Next place one 8” and one 5” adhesive Velcro strip on the roll cage down the back lower portion of the doors to match up with the Velcro tabs sewn to the cab enclosure.
-
Mark the desired locations for the stud snaps on the front fenders. You will use 4 per side. Then install the stud snaps to the Mule using only a #2 Phillips screwdriver. Caution: Do not use a drill as damage to the Mules gas tank can occur!
-
To open and stow the doors, move the zipper fully rearward and fold the bottom portion of the doors up. Then begin to form a vertical roll with the door by rolling it inward from the front edge toward the rear of the door. Secure in place using the two hook and loop straps provided. Try to form a roll approximately 2” in diameter to assure that the door will not stick out very far while stowed.
Cleaning and Storage Recommendations:
- Before removing the Falcon Ridge Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag (I recommend a Flannel or Micro Fiber Cloth) or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.
- It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory On a large, clean and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing.
- A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered.
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date item is received. You MUST package the product exactly
as it was originally packaged from the factory to get a full refund for the
product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory new condition to receive refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridges many distributors’, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory new condition.
NOTE: All windshields must be returned with the original protective film
intact and not removed. Do NOT REMOVE if you have any intentions of returning
the item. Refund/ replacement of a windshield will only be processed on items
with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping cost will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops, and/or windshield due to defects of the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>