Kirisun DP680 Digital Two-Way Radio User Guide

Kirisun DP680 Digital Two-Way Radio

Please read carefully the Safety Information and Warranty Card before using the product

Appearance

Attachments

Installing/removing the battery

1. Press gently the upper part of the belt clip so that it springs up.
2. Align the battery with the battery holder at the back of the radio, and then insert the battery.
3. Push the battery in the direction indicated until the latch is in position.
4. Press the low part of the battery until it is latched.

Charging the battery

1. Plug the power adapter into an AC power socket of the required specifications.
2. Connect the power adapter to the charger, and green LED indicator light is on.
3. Put a battery or the radio installed with a battery into the charger, and make sure the battery contacts well the charging contacts. During charging, red indicator light is on.
4. It takes about 5 hours to fully charge the battery, and then the LED indicator light turns green. After this, wait 1 to 2 hours before taking out the battery to achieve the best performance.
5. Disconnect the power adapter from the socket.

Note:

1. The radio is delivered uncharged. Before using it for the first time, please charge the battery.
2. Always use the supplied lithium battery and desktop charger.
3. A new battery or one that has been stored for more than 2 months after charging needs to be charged for several times to achieve its normal capacity.

Installing/Uninstalling the Antenna

Insert the threaded end of the antenna into the antenna interface, and rotate the antenna tight clockwise. To uninstall the antenna, rotate it counterclockwise.

Installing/Uninstalling Belt Clip

Align the two screw holes of the belt clip with the screws holes at the back of the radio, and screw up the screws using a screwdriver. To uninstall the belt clip, unscrew the screws and take off the belt clip.

Installing Audio Accessory

Connect an audio accessory to the audio accessory interface, and fasten it using the screw.

LED Indicator

(in analog mode).
Orange light flashing| In emergency state, missed a call, receiving a call alert, or scanning.
Red light flashing| Low power, receiving emergency alarm, failed startup self- detection.

Icons DP990/DP995

| Battery Level
The less blank in the icon, the more remaining battery, and vice versa. When the battery is out, the icon turns red.
---|---
| RSSI
The more bars, the stronger the signals, and vice versa. This icon is displayed only when signals are received.
| High-power transmission
| Low-power transmission
| Mute
| New message
| Status message
| Inbox full
| Emergency alarm mode enabled
| Encryption mode enabled
| Man Down enabled
| Voice Operated Transmitting enabled
| Initiating a call
| Receiving a call
| Talk-around mode enabled
| Roaming enabled
 |
 |
| Scanning (and the icon rotating)
| Dwell on conventional channel during scan
| Dwell on priority channel 1 during scan
| Dwell on priority channel 2 during scan
ID type
| (Call type) individual call
| (Call type) group call
| (Call type) all call
Menu item selection
| Item selected
| Item unselected

Basic Operation

1. Powering On/Off
   To power on the radio, rotate the Power/Volume knob clockwise until you a click. The welcome page is displayed, the backlight is on, and there is a “beep” sound. To power off the radio, rotate the Power/Volume knob counterclockwise until you a click.

2. Selecting a Channel
   In standby state, rotate the Channel knob to select a channel.b Each channel can be set to an analog or a digital channel, and you can switch between analog and digital modes by rotating the Channel knob.

3. Adjusting the Volume
   When the radio is on, turn the Power/Volume knob clockwise to turn up the volume, or counterclockwise to turn it down. Note: If you continue to rotate the knob after turning to the minimum volume, the radio will be powered off and you will hear a click.

4. Making a Call
   – Calling a Default Contact If a default contact is already set for a channel, you can call the contact by holding down the PTT key. You may have a default contact set by your dealer for each digital channel.
   – Selecting and Calling a Contact In the menu, select Contact, select a contact from the Contact List, and hold down the PTT key.
   – Dialing to Call a Contact In the menu, select Contact, select Dial, dial a contact’s ID, and hold down the PTT key.

5. Receiving a Call
   Receiving a Call When the radio receives a call, green LED indicator light is on, the call type, caller alias or ID, and incoming icon are displayed on the screen, and the received voice is played. During the call hang time and if no more call is received, you can call back by holding down the PTT key.
   Note: To receive a group call, please have the radio set as a group member by your dealer using the CPS.

6. Emergency Alarm In emergency, you can send an alarm message and a voice message to a specified group for help. You can send the alarm anytime even when the radio is transmitting traffic.

7. Call Log You can check and manage recent outgoing, incoming and missed individual calls.

8. Connecting BT Device (Optional) You can connect the radio to a BT device in two ways.
   – In the home page, press , select ,Available Device and then Search Device, and nearby pairing enabled devices will be displayed. Select a device, and connect.

Troubleshooting

the battery.
R: Poor contact between the battery and the wiring terminals of the power supply.
S: Install the battery again.
R: Dirty battery contacts.
S: Clean battery contacts.
2| Communication failed| R: Poor antenna contact.
S: Install the antenna again.
R: Different frequencies in Rx-Tx frequency pair between both sides.
S: Use the same frequency in TX-RX frequency pair between both sides.
R: Different CTCSS/CDCSS codes on both sides.
S: Set the same CTCSS/CDCSS code on both sides via PC.
R: Beyond communication distance.
S: Decrease communication distance.
4| Programming exception| R: Improper connection.
S: Connect the radio to a PC properly.
R. No USB driver is installed on the PC. S: Install the USB driver on the PC.
R: Poor contact of earphone interface board.
S: Replace the earphone interface board.

Caution for Using the Battery:
Explosion may be incurred by using a battery of a non-supplied model, or by shorting the anode and cathode of the battery.
Charge the battery using the attached charger, and dispose it as instructed.
Do not strike, squeeze, short out or disassemble the battery.
Do not put the battery in a high temperature or throw it into a fire.
Stop using the battery if it is seriously bulged or immersed in water

CE Warning:

1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
2. The product shall only be connected to a USB interface of version USB2.0 or higher.
3. Adapter shall be installed near the equipment and shall be easily accessible.
4. The operating temperature of the device can’t exceed 5650¥ and shouldn’t be lower than -30¥.
5. The plug considered as disconnect device of adapter.
6. The device complies with RF specifications when the device used at 20cm from the body.

Hereby, Kirisun Communication Co.,Ltd. declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states.

FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

ISEDC Warning
This product meets the applicable Industry Canada technical specifications.

RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environment exposure limits always adhere to the following procedures.

Guidelines:
Do not remove the RF Exposure Label from the device. User awareness instructions should accompany device when transferred to other users. Do not use this device if the operational requirements described herein are not met.

Operating Instructions: Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50 % of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). Hold the radio in a vertical position in front of face with the microphone (and the other parts of the radio, including the antenna) at least one inch (2.5 cm) away from the nose. Keeping the radio at the proper distance is important because RF exposures decrease with distance from the antenna. Antenna should be kept away from eyes.
When worn on the body, always place the radio in approved clip, holder, holster, case, or body harness for this product. Use of non-approved accessories may result in exposure levels, which exceed the occupational/controlled environment RF exposure limits. Use only manufacturer’s name approved supplied or replacement antennas, batteries, and accessories. Use of non-manufacturer-name approved antennas, batteries, and accessories may exceed the FCC and IC RF exposure guidelines. For a list approved accessories please consult your local dealer for information.
Kirisun reserves the right to the final interpretation of this document. This document is only for reference, and actual product prevails.

Kirisun Communication Co., Ltd

Documents / Resources

| Kirisun DP680 Digital Two-Way Radio [pdf] User Guide
DP68002, Q5EDP68002, DP680 Digital Two-Way Radio, DP680, Digital Two-Way Radio
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>