BN-LINK T7B Digital Heat Mat Thermostat Controller Instruction Manual
- June 5, 2024
- BN-LINK
Table of Contents
T7B Digital Heat Mat Thermostat Controller
Instruction Manual
PROGRAMMING
STEP 1 CHANGING FROM ºC TO ºF
- Press and hold the UP button for 3 seconds to change the unit to Fahrenheit (F)
- Press and hold the DOWN button for 3 seconds to change the unit to Celsius (°C)
STEP 2 SETTING UP THE THERMOSTAT CONTROLLER
Plug your thermostat controller into an electrical outlet. The POWER
indicator will be on.
A. Programming your thermostat controller
- Press and hold the SET button until the display blinks While the display is blinking, let go of the set button
- Using the UP and DOWN button, adjust the temperature to select your desired temperature while the screen is still blinking
- Press SET again to confirm
B. setup
- By default, the display will reflect the current measured temperature.
- Place sensor probe near or on the heating appliance. Do not submerge the controller or probe in water.
- Plug your appliance into the thermostat controller.
- The HEATING indicator light will only turn on when the controller is actively powering your attached appliance.
When the preset temperature is reached, the HEATING indicator will turn off and power to your attached appliance will stop.
ATTENTION
- If the thermostat remains ‘on’ (delivering power to the heat mat) for more than 5 consecutive hours, it indicates the desired temperatures are not being reached.
- Do not immerse the controller or probe into the water
- Do not exceed a total of 1000 watts of heating devices plugged into thermostat
- If using with seedling heat mats, place the sensor into the rooting area about 1 “. 1%”. Position the thermostat up and away from seedling trays and stray water. Do not expose the probe to water.
TECHNICAL SPECIFICATIONS
- Works great for controlling plant or pet heat mat temperature
- Accurate LED display in 0.1-degree increments
- 1-degree increments for temperature setting
- Max Load: 1000 Watts
- Max Amps: 8.3 A
- 120 V input & output voltage
- Temperature control range: 40 – 108 F (5 – 42 C)
- Temperature display range: 32 – 140 F (0- 60 °C)
- Saves current program after powering off
- Includes power and load indicator lights
- Includes 3 prong grounded electrical plug
ABNORMAL WARNING
If thermostat shows
- ‘E1’: the actual temperature is lower than 32 °F or 0 °C.
- ‘E2’: the actual temperature is higher than 108 F or 60 °C.
- ‘E3: the temperature sensor is not working properly.
WARNING
This product contains a soldered fuse and cannot be replaced.
Please heed the following advice to prevent overloading the fuse.
- We do not recommend using this product with any appliance with a compressor. Examples include refrigerators, A/Cs (air conditioners), or water cooling dispensers.
- This product works well with heat mats, aquarium heaters, fans, and lights with a rating of up to 1000W.
- Please keep the (HE) rating of the appliances
- The controller is designed to have a 3-degree buffering zone before powering on again after reaching the set temperature. This is to preserve the fuse built into the unit.
For example: If you set your temperature controller to 95. Your heating
thermostat controller will heat your appliance up to the set temperature and
turn off your heating appliance. Once the ambient temperature on your heating
controller drops down to 92. The heating controller will activate your heating
appliance again and heat it back up to 95 and turn it off.
This process will repeat
TROUBLESHOOTING:
HEAT MAT IS NOT REACHING THE SET TEMPERATURE?
Standard heating mats will not fully heat a lot of tanks in the market. The
heat mat itself does not have to supply enough power to heat the entire tank.
The temperature probe is reading the temp at the probe and adjusts to that.
You should tape the probe directly to the “Under Tank Heater (UTH)” , then set
the temperature however high you need it to get the bottom of the cage to the
appropriate temp. Just some insight, a heat mat is only really good for belly
heat and won’t raise the ambient temps much. This is not the tstat
malfunctioning.
If you need more assistance, we have a helpful short instructional video that
most of our customers find helpful. Please enter the model number provided on
the back of your product to YouTube and you will find a helpful instructional
video made by one of our technical support team members.
(http://www.Youtube.com)
BN-LINK INC.
12991 Leffingwell Avenue, Santa Fe Springs
Customer Service Assistance: 1.909.592.1881
E-mail: support@bn-link.com
http://www.bn-link.com
Hours: 9 AM- 5 PM PST, Mon – Fri
Designed in California and Made in China
Documents / Resources
| BN-
LINK T7B Digital Heat Mat Thermostat
Controller
[pdf] Instruction Manual
T7B, Digital Heat Mat Thermostat Controller, T7B Digital Heat Mat Thermostat
Controller
---|---