DEWALT DXV09P-QTA 9 Gallon 34L Portable Wet or Dry Vacuum Instruction Manual

DXV09P-QTA 9 Gallon 34L Portable Wet or Dry Vacuum
Instruction Manual

DEFINITIONS: SAFETY ALERT SYMBOLS AND WORDS
This instruction manual uses the following safety alert symbols and words to alert people of hazardous
situations and the risk of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury that, if not avoided, may result in property damage.

1: Handle
2: Power switch
3: Lid latch
4: Hose strap
5: Vacuum port
6: Dust tank
7:Rubberized caster
8: Drain port
9: 1-7/8″ Crush resistant hose (DXVA 19-2500)| 10: Extension wand (DXVA19-1200A)
11: Floor nozzle (DXVA 19-2591)12: Round brush (DXVA 19-2400)
13: Accessory bag with holder (DXVA 19-5156)
14: Disposable filter bag (DXVA 19-4101)
15: Caster Crevice nozzle (DXVA 19-1400)
16: BB Self-tapping screw Utility nozzle (DXVA19-1300)
17: Clean connect- filter (DXVC6910) cc Bracket
18: Instruction manual DD Phillips screwdriver (Not Included)| AA: Caster
BB: Self-tapping screw
CC: Bracket
DD: Phillips screwdriver (Not Included)
---|---|---

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
WARNING: To reduce the risk of injury, read the instruction manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
When using electrical appliances, always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury, including the following:
BEFORE USING THIS APPLIANCE, READ AND FOLLOW ALL INSTRUCTIONS.

WARNING: To reduce the risk of electric shock. Do not expose to rain. Store indoors.

• Do not leave the appliance when it is connected to a power source. Unplug it from the outlet when not in use and before servicing.
• Do not allow the appliance to be used as a toy. Pay close attention when the appliance is used by or near children.
• Use this appliance ONLY as described in the manual. Use only DEWALT recommended attachments.
• Do not use this appliance with a damaged cord or plug. If the appliance is not working correctly, or if it has been dropped, damaged, left outdoors, or dropped in water, return it to a service center
• Do not pull or carry this appliance by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the appliance over the cord. Keep cord away from heated surfaces.
• Do not unplug this appliance by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not handle the plug or appliance with wet hands.
• Do not put any objects into the openings of the appliance. Do not use the appliance with any opening blocked; keep free of dust, lint, hair, and anything else that may reduce air flow.
• Keep hair, loose clothing, fingers, and all body parts away from the openings and moving parts.
• Turn off all controls before unplugging the appliance.
• Take extra care when cleaning on stairs.
• Do not use the appliance to pick up flammable or combustible liquids, such as gasoline, or use it in areas where flammable or combustible liquids are present.
• Static shocks are possible in dry areas or when the relative humidity of the air is low. This is only temporary and does not affect the use of the vacuum. To reduce the frequency of static shocks, add moisture to the air with a console, installed a humidifier, or use an anti-static hose (standard on some models).
• To avoid spontaneous combustion, empty the dust tank after each use.

SAVE THESE INSTRUCTIONS AND ADDITIONAL SAFETY RULES
WARNING:

• Do not pull or carry this appliance by the cord, use
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use to vacuum combustible explosive materials, such as coal, grain, or other finely divided combustible materials.
• Do not use to vacuum hazardous, toxic, or carcinogenic materials, such as asbestos or pesticide.
• Never pick up explosive liquids (e.g. gasoline, diesel fuel, heating oil, paint thinner, etc.), acids, or solvents.
• Do not use a vacuum without filters in place
• Some wood contains preservatives that can be toxic. Take extra care to prevent inhalation and skin contact when working with these materials. Request and follow any safety information available from the material supplier.
• Do not use a vacuum as a step ladder.
• Do not place heavy objects in the vacuum.
• An extension cord must have adequate
• An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension cord contains at least the minimum wire size. The following table shows the correct size to use. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
• If an extension cord is to be used outdoors it must be marked with the suffix W-A or W following the cord type designation. For example – SJTW-A indicates it is acceptable for outdoor use.

Minimum Gauge for Cord Sets

Ampere Rating| Volts| Total Length of Cord In Feet (meters)
120V| 25 (7.6)| 50 (15.2)| 100 (30.5)| 150 (45.7)
240V| 50 (15.2)| 100 (30.5)| 200 (61.0)| 300 (91.4)
More
Than| Not More
Than| AWG
0| 6| | 18| 16| 16| 14
6| 10
18| 16| 14| 12
10| 12
16| 16| 14| 12
12| 16| 14| 12| Not Recommended

WARNING: Always use safety goggles. Everyday eyeglasses are NOT safety goggles. Also, use a face or dust mask if the area of operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/ CSA Z94.3),
• NIOSH/ OSHA/ MSHA respiratory protection.
  

To reduce the exposure to these chemicals, wear approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.
WARNING:
SERVICING OF DOUBLE-INSULATED WET/DRY VAC
In a double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double- insulated Wet/Dry Vac requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double-insulated Wet/Dry Vac must be identical to the parts they replace. This double-insulated Wet/Dry Vac is marked with the words “DOUBLE-INSULATED” and the symbol (square within a square) may also be marked on the appliance. To reduce the risk of injury from electrical shock, unplug the power cord before servicing the electrical parts of the Wet/Dry Vac. SERVICING OF DOUBLEINSULATED WET/DRY VAC In a double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double-insulated Wet/Dry Vac requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double-insulated Wet/Dry Vac must be identical to the parts they replace. This double-insulated Wet/Dry Vac is marked with the words “DOUBLE-INSULATED” and the (square within a square) may also be marked on the appliance. To reduce the risk of injury from electrical shock, unplug the power cord before servicing the electrical parts of the Wet/Dry Vac.
WARNING: If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid a hazard.
**WARNING : Remove the plug from the socket before performing maintenance. Before using the machine make sure that the frequency and voltage shown on the rating plate correspond with the mains voltage. Specifications and details are subject to change without prior notice. The accessories shown in the pictures may vary from model to model.
IMPORTANT SAFEGUARDS : The symbol on the product or packaging indicates that the product must not be treated as domestic refuse. Instead, it should be handed into a collection point for the recycling of electrical and electronic components. By ensuring the product is treated in the correct manner, you will help prevent any negative impact on the environment and health that might arise when the product is discarded as ordinary refuse. For further information about recycling, you should contact our local authorities, refuse collection service or the sales outlet where you bought the goods.
WARNING:
This product can expose people to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
WARNING:**
This product is NOT to be used for altering pathogens, for example, COVID-19. Follow all local, state, and federal guidance on general cleaning practices.

WARNING:

• TO REDUCE THE RISK OF INJURY, USERS MUST READ THE INSTRUCTION MANUAL. DO NOT RUN UNATTENDED. DO NOT PICK UP FLAMMABLE, COMBUSTIBLE, OR HOT MATERIALS. DO NOT USE AROUND EXPLOSIVE DUST, LIQUIDS, OR VAPORS. ELECTRICAL DEVICES PRODUCE ARCS OR  PARKS WHICH CAN CAUSE FIRE OR EXPLOSION. DO NOT USE IT AT FILLING STATIONS OR ANYWHERE GASOLINE IS STORED OR DISPENSED. DO NOT VACUUM TOXIC OR CARCINOGENIC MATERIALS OR OTHER HEALTH-ENDANGERING MATERIALS SUCH AS ASBESTOS OR PESTICIDES. ALWAYS  SE PROPER EYE AND RESPIRATORY PROTECTION. TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE YOURSELF TO RAIN. STORE  INDOORS. WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. DO NOT BE USED AS A STEP STOOL.

PRODUCT SPECIFICATIONS

SAVE THESE INSTRUCTIONS

OPERATING INSTRUCTIONS

UNPACKING & SETUP SUMMARY

1. Pull lid latches in an outward motion, and remove the power head and some accessories that may have been shipped in the tank.
2. Assemble the casters, following the instructions under CASTER ASSEMBLY in this manual.
3. Assemble the accessory bag holder, following the instructions under ACCESSORY BAG HOLDER ASSEMBLY in this manual.
4. Attach accessories following the instructions in this manual.
5. Before replacing the power head, refer to this manual to ensure you have the proper lter installed for the cleaning operation.
6. Replace the power head, and apply pressure with the thumb to each latch until it snaps tightly in place. Make sure all lid latches are clamped securely.
7. . Insert the hose end into the inlet of the tank.
8. Attach the extension wands to the end of the hose. Apply slight pressure until the thing is tight.
9. Attach one of the cleaning accessories (depending on the cleaning requirements) to the extension wands. Twist slightly to tighten the connection.
10. Plug the cord into the wall outlet. The vacuum is ready for use.
11. To reduce the risk of injury from accidental starting, always shut off the vacuum and disconnect the power plug from the wall outlet before installing any part or cleaning the accessory.

WARNING:
Do not alter the plug in any way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a qualified electrician to install the proper outlet.
WARNING:
To reduce the risk of re or explosion, do not operate this vac in areas with flammable gases, vapors, or explosive dust in the air. Flammable gases or vapors include but are not limited to lightered, solvent-type cleaners, oil- based paints, gasoline, alcohol, or aerosol sprays. Explosive dust includes but is not limited to coal, magnesium, aluminum, and grain or gun powder. Do not vacuum explosive dust, flammable or combustible liquids, or hot ashes. Do not use this vac as a sprayer for any flammable or combustible liquid. To reduce the risk of health hazards from vapors or dust, do not vacuum toxic materials.

WARNING:
The operation of any utility vac can result in foreign objects being blown into the eyes, which can result in severe eye injury. Always wear safety goggles complying with ANSI Z87.1 (or in Canada, CSA Z94.3) before starting operation.
CASTER ASSEMBLY

1. Invert the dust tank, and take the caster to align the tank bottom sinking place. Secure with screws provided.
2. Return dust tank assembly upright.

ACCESSORY BAG HOLDER ASSEMBLY
Attach side tank handles to tank with screws provided. Insert the accessory bag holder into the hole of the bracket (see illustration).

WARNING:
To reduce the risk of re or explosion, do not operate this vac in areas with flammable gases, vapors, or explosive dust in the air. Flammable gases or vapors include but are not limited to lightered, solvent-type cleaners, oil- based paints, gasoline, alcohol, or aerosol sprays. Explosive dust includes but is not limited to coal, magnesium, aluminum, and grain or gun powder. Do not vacuum explosive dust, flammable or combustible liquids, or hot ashes. Do not use this vac as a sprayer for any flammable or combustible liquid. To reduce the risk of health hazards from vapors or dust, do not vacuum toxic materials.
WARNING:
The operation of any utility vac can result in foreign objects being blown into the eyes, which can result in severe eye injury. Always wear safety goggles complying with ANSI Z87.1 (or in Canada, CSA Z94.3) before starting operation.
After you plug the power cord into the wall receptacle, turn the unit “ON” by pushing the switch from position “O” to position “I”. The “O” is the “OFF” position, and the “I” is the “ON” position.

DRY PICK-UP

1. The lter must always be in the correct position to reduce the risk of leaks and possible damage to the vac. Make sure that the lter is completely covering the lter cage. Make sure there are no gaps between the lter and the lid. It is very important to assemble the lter to the cage without any possible leaks or tears.
2. When using the vac to pick up new dust, it will be necessary to empty the dust tank and clean or replace the lter at more frequent intervals to maintain peak vac performance.

NOTICE:
A dry lter is necessary to pick up dry material. I use the vac to pick up dust when the lter is wet, the lter will clog quickly and be very difficult to clean. If the lter gets wet, replace it before continuing to do dry pickups.
INSTALLING THE CARTRIDGE FILTER
The cartridge lter can be used for wet or dry pick-up, installation is the same for both.

1. With the power head in an upside-down position, slide the cartridge lter down over the lid cage, and push the lter seals against the power head.
2. Turn the knob on lter retainer clockwise to tighten, the lter into place.
3. To remove the lter for cleaning, turn the lter knob counterclockwise till feel the tactile and auditory cue, and make sure the knob arrow aligns with the “Unlock” icon on the lter cap, then slide the cartridge lter off the lid cage. then grasp the step of the knob tightly with fingers to pull the cartridge lter out off the cage.
4. To clean the cartridge lter, shake or brush off excess dirt or rinse (from the inside of the lter) with water, dry completely (approximately 24 hours) and re-install.

NOTICE:
If the lter has been used for wet pick-up, it must be cleaned and dried before dry pick-up.

INSTALLING THE DISPOSABLE FILTER BAG

1. Slide the cardboard collar opening firmly onto the vacuum port detector until it stops against the detector wall.
2. Position the bag so that it is distributed around the inside of the tank.
3. Replace and secure the power head onto the tank.

WET PICK-UP
The cartridge filter must be positioned over the lter cage while vacuuming liquids. When picking up several tanks full of liquid, the cartridge lter will become saturated, and misting may appear in the exhaust air. At this time, they should dry or replace the cartridge lter to eliminate the misting and possible liquid dripping around the lid. After completing a wet pick-up job, raise the hose to drain any excess liquid into the tank before shutting off. The interior of the tank should be periodically cleaned

1. Always disconnect the plug from the wall outlet before removing the power head. Place the power head in an upside-down position. Remove the cartridge lter by sliding it up and off the lter cage

2. Shake excess dust off the cartridge lter with a rapid up and down movement.
   NOTE: WET PICK-UP ACCESSORIES SHOULD BE WASHED PERIODICALLY, ESPECIALLY AFTER PICKING UP WET, STICKY FLUIDS OR SPILLS. THIS CAN BE ACCOMPLISHED WITH A WARM SOLUTION OF SOAP AND WATER.

3. This wet/dry vac is equipped with an oat mechanism that will rise automatically to cut off the arrow when the liquid in the tank reaches a predetermined level. When this happens, turn off the vac, unplug the power cord, and empty the dust tank. You will know that the oat has shut the arrow off because the suction ceases and the motor noise becomes higher in pitch due to increased motor speed. The liquid capacity may vary with the rate of pickup.

IMPORTANT: To reduce the risk of damage to the vac, do not run the motor with the oat in the raised position.

NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD LOSE SUCTION. IF THIS OCCURS, PLACE VAC IN AN UPRIGHT POSITION AND TURN THE SWITCH OFF. THIS WILL ALLOW THE FLOAT TO RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE TO CONTINUE OPERATION.
EMPTY THE TANK
WARNING:
To reduce the risk of injury from accidental starting, unplug the power cord before emptying the dust tank.

1. Remove the power head assembly of the wet/dry vac by pulling outward on the lid latch located on each side of the vac. Lift off the power head assembly
2. Dump the tank contents into the proper waste disposal container.
3. Liquids may be emptied through the tank drain. To empty, turn the unit off and remove the plug from the wall outlet. Remove the drain cap and deposit the liquid waste contents in a suitable drain. After the tank is empty, return the drain cap to its original position. To continue use, plug the cord into the wall outlet and turn the unit on.

**CARE AND MAINTENANCE FILTER REPLACEMENT

**

WARNING:
To reduce the risk of injury from accidental starting, unplug the power cord before changing or cleaning the lter. The lter should be cleaned often to maintain peak vac performance.
WARNING:
Do not remove the lter cage and oat. The oat prevents water from entering the impeller and damaging the motor. The cage prevents users from touching the moving impeller.
NOTICE:
To avoid damage to the impeller and motor, always reinstall the Clean Connect™ lter before using the vac for dry pickups and wet pickups.
NOTICE:
After cleaning, check the lter for tears or small holes. Do not use a filter with holes or tears in it. Even a small hole can cause a lot of dust to come out of the vac. Replace it immediately.
NOTICE:
Before installing the filter on the vac, clean the area of the lid so that the lter will seal against the lid and stop small particles from bypassing the filter bag. If the filter is clean and not damaged, replace it on the lter cage. If it cannot be reused, place a new lter over the lter cage.
NOTICE:
Clean the Filter in an open area. Cleaning should be done outdoors and not in living quarters.

CLEANING
To keep the wet/dry vac looking its best, clean the outside with a cloth dampened with warm water and mild soap. To clean the tank:

1. Dump out debris.
2.  Wash the tank thoroughly with warm water and mild soap.
3. Wipe with a dry cloth.

STORAGE
Before storing the vac, the dust tank should be emptied and cleaned. The cord should be wrapped and hung on the unit and the accessories should be kept in the accessory bag so they can be readily available. The vac should be stored indoors.

TROUBLESHOOTING

Minor problems often can be fixed without calling customer service.

Ensure the on/off switch is in the ON position (I).
Suction capacity decreases| Remove blockages in the suction nozzle, suction tube, suction hose, or filters.
Replace the paper or fleece dust bag.
Check for proper installation of the filters.
Clean or replace the filters.
Empty the dust tank, refer to Empty the tank under Operating instructions.
Vacuum stops running| Thermal overload has been tripped:
1. Turn the vacuum off and disconnect the vacuum cleaner from the power source.
2. Empty the canister, if needed
3. Allow the unit to cool.
4. Plug the power cord into an appropriate outlet and turn on/off switch to the ON position (0 to test. If the vacuum will not restart call 1-888-899-0146.
Dust comes out while vacuuming| Check for proper installation of the filters.
Ensure filters are not damaged; replace if necessary.
Ensure filter seals are in place and secure.

EXPLODED VIEW / PARTS LIST

WARRANTY

Alton Industry Ltd. Group
3-Year Limited Warranty
This warranty covers any defects in materials or workmanship of the enclosed product. Alton Industry Ltd. Group will repair or replace any defective materials due to the craftsmanship of the product. This warranty does not cover any problem caused by misuse, abuse, accidents, or acts of God, such as floods or hurricanes. Consequential and incidental damages are not covered under this warranty. Coverage terminates if you sell or otherwise transfer the ownership. If you feel you have a defective product, please  submit a copy of your receipt to the address below and call 1-888-899-0146 for instructions prior to returning this item to the store or sending it back to:
Alton Industry Ltd. Group
643 Innovation Drive
West Chicago, IL 60185
We will inspect the product and contact you within 72 hours to give you the results of our inspection. We reserve the right to repair or replace the product at our discretion. However, we may replace the product with one of similar but not exact features. Parts and Service Information available call Alton Industry at 1-888-899-0146. This warranty gives you specific legal rights. You may have other rights which vary from state to state.
Copyright © 2022 DEWALT.
DEWALT ® and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an affiliate thereof, and are used under license.
The yellow/black color scheme is a trademark for DEWALT power tools & accessories

www.DeWALT.com
If you have questions or comments, contact us.
1-888-899-0146
 

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>