MINN KOTA PowerDrive V2 Bow-Mount Trolling Motor User Manual

June 5, 2024
MINN KOTA

MINN KOTA PowerDrive V2 Bow-Mount Trolling Motor

MINN-KOTA-PowerDrive-V2-Bow-Mount-Trolling-Motor-
product

CE MASTER USER MANUAL (FOR CE/C-TICK CERTIFIED MODELS) Conforms to 89/336/EEC (EMC) under standards EN 55022A, EN 50082-2 since 1996 LN V9677264

THANK YOU
Thank you for choosing Minn Kota. We believe that you should spend more time fi shing and less time positioning your boat. That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantage that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you catch more fi sh. REMEMBER TO KEEP YOUR RECEIPT AND IMMEDIATELY REGISTER YOUR TROLLING MOTOR. A registration card is enclosed or you can complete registration on our website at minnkotamotors.com.

NOTE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You may obtain service by: calling Minn Kota at 800-227-6433; returning your motor to the Minn Kota Factory Service Center; sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on our website, at minnkotamotors.com. Please include proof of purchase, serial number and purchase date for warranty service with any of the above options.
Please thoroughly read this user manual. Follow all instructions and heed all safety and cautionary notices below. Use of this motor is only permitted for persons that have read and understood these user instructions. Minors may use this motor only under adult supervision.

ATTENTION: Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected from the power source when it is not in use or is off the water. When connecting the power-supply cables of the motor to the battery, ensure that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motor make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions may result in electric shorts of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking the propeller. Avoid submerging the complete motor as water may enter the lower unit through control head and shaft. If the motor is used while water is present in the lower unit considerable damage to the motor can occur. This damage will not be covered by warranty.

CAUTION: Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects. The motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and for fl oating objects. Persons whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other substances are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise pressure level of the motor during use is less than 70dB(A). The overall vibration level does not exceed 2,5m/sec2.

TWO-YEAR LIMITED WARRANTY

WARRANTY ON MINN KOTA FRESHWATER TROLLING MOTORS
Johnson Outdoors Marine Electronics, Inc. (“JOME”) extends the following limited warranty to the original retail purchaser only. Warranty coverage is not transferable.

MINN KOTA LIMITED TWO-YEAR WARRANTY ON THE ENTIRE PRODUCT
JOME warrants to the original retail purchaser only that the purchaser’s new Minn Kota freshwater trolling motor will be materially free from defects in materials and workmanship appearing within two (2) years after the date of purchase. JOME will (at its option) either repair or replace, free of charge, any parts found by JOME to be defective during the term of this warranty. Such repair, or replacement shall be the sole and exclusive liability of JOME and the sole and exclusive remedy of the purchaser for breach of this warranty.

MINN KOTA LIMITED LIFETIME WARRANTY ON COMPOSITE SHAFT
JOME warrants to the original retail purchaser only that the composite shaft of the purchaser’s Minn Kota trolling motor will be materially free from defects in materials and workmanship appearing within the original purchaser’s lifetime. JOME will provide a new composite shaft, free of charge, to replace any composite shaft found by JOME to be defective during the term of this warranty. Providing a new composite shaft shall be the sole and exclusive liability of JOME and the sole and exclusive remedy of the purchaser for breach of this warranty; and purchaser shall be responsible for installing, or for the cost of labor to install, any new composite shaft provided by JOME.

EXCLUSIONS & LIMITATIONS
This limited warranty does not apply to products that have been used in saltwater or brackish water, commercially or for rental purposes. This limited warranty does not cover normal wear and tear, blemishes that do not aff ect the operation of the product, or damage caused by accidents, abuse, alteration, modifi cation, shipping damages, acts of God, negligence of the user or misuse, improper or insuffi cient care or maintenance. DAMAGE CAUSED BY THE USE OF OTHER

REPLACEMENT PARTS NOT MEETING THE DESIGN SPECIFICATIONS OF THE ORIGINAL PARTS WILL NOT BE COVERED BY THIS LIMITED WARRANTY.
The cost of normal maintenance or replacement parts which are not in breach of the limited warranty are the responsibility of the purchaser. Prior to using products, the purchaser shall determine the suitability of the products for the intended use and assumes all related risk and liability. Any assistance JOME provides to or procures for the purchaser outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of the terms, limitations or exclusions, nor will such assistance extend or revive the warranty. JOME will not reimburse the purchaser for any expenses incurred by the purchaser in repairing, correcting or replacing any defective products or parts, except those incurred with JOME’s prior written permission. JOME’S AGGREGATE LIABILITY WITH RESPECT TO COVERED PRODUCTS IS LIMITED TO AN AMOUNT EQUAL TO THE PURCHASER’S ORIGINAL PURCHASE PRICE PAID FOR SUCH PRODUCT.

MINN KOTA SERVICE INFORMATION
To obtain warranty service in the U.S., the product believed to be defective, and proof of original purchase (including the date of purchase), must be presented to a Minn Kota Authorized Service Center or to Minn Kota’s factory service center in Mankato, MN. Any charges incurred for service calls, transportation or shipping/freight to/from the Minn Kota Authorized Service Center or factory, labor to haul out, remove, re-install or re-rig products removed for warranty service, or any other similar items are the sole and exclusive responsibility of the purchaser. Products purchased outside of the U.S. must be returned prepaid with proof of purchase (including the date of purchase and serial number) to any Authorized Minn Kota Service Center in the country of purchase. Warranty service can be arranged by contacting a Minn Kota Authorized Service Center or by contacting the factory at 1-800-227-6433 or email service@minnkotamotors.com. Products repaired or replaced will be warranted for the remainder of the original warranty period [or for 90 days from the date of repair or replacement, whichever is longer]. For any product that is returned for warranty service that JOME fi nds to be not covered by or not in breach of this limited warranty, there will be a billing for services rendered at the prevailing posted labor rate and for a minimum of at least one hour.

NOTE: Do not return your Minn Kota product to your retailer. Your retailer is not authorized to repair or replace products.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. IN NO EVENT SHALL ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND THE DURATION OF THE RELEVANT EXPRESS LIMITED WARRANTY. IN NO EVENT SHALL JOME BE LIABLE FOR PUNITIVE, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. Without limiting the foregoing, JOME assumes no responsibility for loss of use of product, loss of time, inconvenience or other damage. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations and/or exclusions may not apply to you. This warranty gives you specifi c legal rights and you may also have other legal rights which vary from state to state.

FEATURES

MINN-KOTA-PowerDrive-V2-Bow-Mount-Trolling-Motor-1

MOUNT INSTALLATION

TOOLS AND RESOURCES REQUIRED:

  • 3 Phillips Screw Driver

  • Drill
  • 9/32” Drill Bit
  • 7/16” Box End Wrench
  • A second person to help with the installation
  1. Remove the four sideplate screws. Remove the right sideplate and swing the left sideplate out and away from the base extrusion.

  2. Place the motor on the bow of the boat in the deployed position.

  3. We recommend that the motor be mounted as close to the centerline of the boat as possible.

  4. Make sure that the area under the mounting location is clear and unobstructed for drilling and accessible for you to attach nuts and washers.

  5. Make sure the mount is positioned so that the shaft is out beyond the rub rail of the boat by 1-½”. The lower unit, as it is lowered into the water or raised into the boat, must not encounter any obstructions.
    CAUTION : Make sure the motor is mounted on a level surface and is not connected to
    a power source. Use the rubber washers to create a level surface if necessary.

  6. Once in position, mark four of the twelve holes (two on each side) provided in the bow mount base for drilling. If possible, use the four holes that are farthest apart. Drill through the marked holes using the 9/32” drill bit.

  7. Mount the plate to the bow using the provided bolts, nuts, and washers.

  8. Replace the sideplates and sideplate screws.

MINN-KOTA-PowerDrive-V2-Bow-Mount-Trolling-Motor-2

BATTERY WIRING & INSTALLATION

BOAT RIGGING & PRODUCT INSTALLATION
For safety and compliance reasons, we recommend that you follow American Boat and Yacht Council (ABYC) standards when rigging your boat. Altering boat wiring should be completed by a qualifi ed marine technician. The following specifi cations are for general guidelines only:

CAUTION: These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devices from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer than that provided with your unit, follow the conductor gauge and circuit breaker sizing table below. If your wire extension length is more than 25 feet, we recommend that you contact a qualifi ed marine technician.
An over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements dictate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. The type (voltage and current rating) of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The table below gives recommended guidelines for circuit breaker sizing.

Reference:
United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment ABYC E-11: AC and DC Electrical Systems on Boats

CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE

Motor Thrust / Model| ****

Max Amp Draw

| ****

Circuit Breaker

| Wire Extension Length *
---|---|---|---
5 feet| 10 feet| 15 feet| 20 feet| 25 feet
30 lb.| 30| ****

50 Amp @ 12 VDC

| 10 AWG| 10 AWG| 8 AWG| 6 AWG| 4 AWG
40 lb., 45 lb.| 42| 10 AWG| 8 AWG| 6 AWG| 4 AWG| 4 AWG
50 lb., 55 lb.| 50| 60 Amp @ 12 VDC| 8 AWG| 6 AWG| 4 AWG| 4 AWG| 2 AWG
70 lb.| 42| 50 Amp @ 24 VDC| 10 AWG| 10 AWG| 8 AWG| 8 AWG| 6 AWG
80 lb.| 56| 60 Amp @ 24 VDC| 8 AWG| 8 AWG| 8 AWG| 6 AWG| 6 AWG
101 lb.| 46| 50 Amp @ 36 VDC| 8 AWG| 8 AWG| 8 AWG| 8 AWG| 8 AWG
Engine Mount 101| 50| 60 Amp @ 36 VDC| 8 AWG| 6 AWG| 4 AWG| 4 AWG| 2 AWG
112 lb.| 52| 60 Amp @ 36 VDC| 8 AWG| 8 AWG| 8 AWG| 8 AWG| 8 AWG
Engine Mount 160| 116| (2) x 60 Amp @ 24 VDC| 2 AWG| 2 AWG| 2 AWG| 2 AWG| 2 AWG
E-Drive| 40| 50 Amp @ 48 VDC| 10 AWG| 10 AWG| 10 AWG| 10 AWG| 10 AWG

This conductor and circuit breaker sizing table is only valid for the following assumptions: 1

  1. No more than 3 conductors are bundled together inside of a sheath or conduit outside of engine spaces.
  2. Each conductor has 105° C temp rated insulation.
  3. No more than 5% voltage drop allowed at full motor power based on published product power requirements.

PUSH-TO-TEST BATTERY METER
This motor is equipped with a “push-to-test” battery meter. The LED provides an accurate display of the remaining charge in the battery. It is only accurate when the motor is off . The meter reads as:

  • One light indicates recharge.
  • Two lights indicate low charge.
  • Three lights indicate good charge.
  • Four lights indicate full charge.

SELECTING THE CORRECT BATTERIES
The motor will operate with any lead acid, deep cycle marine 12 volt battery/batteries. For best results, use a deep cycle, marine battery with at least a 105 ampere hour rating. Maintain battery at full charge. Proper care will ensure having battery power when you need it, and will signifi cantly improve the battery life. Failure to recharge lead-acid batteries (within 12-24 hours) is the leading cause of premature battery failure. Use a multi- stage charger to avoid overcharging. We off er a wide selection of chargers to fi t your charging needs. If you are using a crank battery to start a gasoline outboard, we recommend that you use a separate deep cycle marine battery/batteries for your Minn Kota trolling motor.

Advice Regarding Batteries:

  • Never connect the (+) and the (–) terminals of the same battery together. Take care that no metal object can fall onto the battery and short the terminals. This would immediately lead to a short and extreme fi re danger.
  • It is highly recommended that a circuit breaker or fuse be used with this trolling motor. Refer to “Conductor Gauge and Circuit Breaker Sizing Table” in the previous section to fi nd the appropriate circuit breaker or fuse for your motor. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended
CONNECTING THE BATTERIES

12 VOLT SYSTEMS:

  1. Make sure that the motor is switched off (speed selector on “OFF” or “0”).
  2. Connect positive ( + ) red lead to positive ( + ) battery terminal.
  3. Connect negative ( – ) black lead to negative ( – ) battery terminal.
  4. For safety reasons do not switch the motor on until the propeller is in the water.

CAUTION:
For safety reasons, disconnect the motor from the battery/batteries when the motor is not in use or while the battery/batteries are being charged.

CONNECTING THE BATTERIES IN SERIES (IF REQUIRED FOR YOUR MOTOR)

24 VOLT SYSTEMS:

  1. Make sure that the motor is switched off (speed selector on “0”).
  2. Two 12 volt batteries are required.
  3. The batteries must be wired in series, only as directed in wiring diagram, to provide 24 volts.
  4. Connect a connector cable to the positive ( + ) terminal of battery 1 and to the negative ( – ) terminal of battery 2.
  5. Connect positive ( + ) red motor lead to positive ( + ) terminal on battery 2.
  6. Connect negative ( – ) black motor lead to negative ( – ) terminal of battery 1.
  7. For safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and follow instructions in your boat owner’s manual. See wiring diagram on following pages.

CAUTION

  • For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries are being charged.
  • Improper wiring of 24/36 volt systems could cause battery explosion!
  • Keep leadwire wing nut connections tight and solid to battery terminals.
  • Locate battery in a ventilated compartment.

MOTOR WIRING DIAGRAM

NOTE : This is a universal, multi-voltage diagram. Double check your motor’s voltage for proper connections. Over-Current Protection Devices not shown in this illustration.

MINN-KOTA-PowerDrive-V2-Bow-Mount-Trolling-Motor-5

USING & ADJUSTING THE MOTOR

STOWING AND DEPLOYING THE MOTOR
When raising or lowering the motor, keep fi ngers clear of all hinge and pivot points and all moving parts.

  1. Loosen the depth collar screw.
  2. Push Deploy-Assist Lever down.
  3. Push motor out.
  4. Tighten the depth collar screw.

MINN-KOTA-PowerDrive-V2-Bow-Mount-Trolling-Motor-6

TO DEPLOY THE MOTOR
Loosen the Dept Collar screw, then push fi rmly down on the Deploy-Assist Lever to release the collar and slide the motor forward, out from the ramp. Lower the motor to the desired depth. Make sure it clicks into a secure, vertical position.

TO STOW THE MOTOR
Push down on the Tilt Lock Lever and raise the motor by pulling up on the composite shaft or control head. Pull the motor toward the stern until it rests securely on the ramp and the Deploy-Assist Lever captures the latch collar. Slide the depth collar down and secure it against the top of the steering housing to secure the motor in place and prevent accidental deployment.

TRANSPORTATION
In conditions where the stowed motor is subject to high levels of shock or vibration, take care to provide a secure stow. Move the depth collar snug against the steering motor and tighten.

TO ADJUST THE LATCH COLLAR
The latch collar is adjustable. If needed, loosen the Phillips head screw and rotate the collar up or down to re-align the latch and collar. The ideal adjustment is a slightly loose fi t that completely captures the collar.

AUTOPILOT™ CONTROLS

(ON AUTOPILOT EQUIPPED MOTORS ONLY)
The Minn Kota AutoPilot™ uses a magnetic compass and a microprocessor chip to keep the trolling motor pointed in the direction you want to go. Each time the wind or water current moves the boat off course, the AutoPilot senses the change and steers itself back to the original heading. The AutoPilot direction is set every time a steering change is made. To change direction, steer until the control head points to the desired course. The AutoPilot will pull the bow of the boat around and correct automatically until the boat is moving in the direction you chose.

  1. This unit has an automatic steering shutdown for safety. In conditions where an obstruction prevents the trolling motor from turning, or in extremely windy conditions, the automatic steering may stop. Any steering input will reset the system to normal.
  2. When the AutoPilot is on and the trolling motor is pulled out of the water to the stow position, the steering motor will continue to run. Turn off the AutoPilot switch to stop the motor. If the switch is left on, the steering motor will shut off automatically after 10 seconds. The motor should not be sored in this condition for long periods as power is still being applied to all eletronics. Always turn the Autopilot switch off and disconnect your motor from the battery when storing your boat.
  3. This unit uses a magnetic compass to detect direction of travel. The compass can be adversely aff ected by magnets or large, ferrous metal objects near (within 12” of) the trolling motor control head.
  4. After steering to a new direction, there is a short delay before the direction is locked in to allow the compass to stabilize.
  5. Obstructions on the propeller may cause excessive vibration of the motor head. This vibration can cause the compass to wander and erratic steering to occur. Clear the obstruction to return the motor to normal operation.
  6. When broad speed changes are made, the motor heading may change slightly. This is normal.

NOTE : Always turn the AutoPilot switch off and disconnect your motor from the battery when storing your boat.

ADJUSTING THE DEPTH OF THE MOTOR
When setting the depth be sure the top of the motor is submerged at least 12” to avoid churning or agitation of surface water. The propeller must be completely submerged.

  1. With the motor deployed, fi rmly grasp the composite shaft above the mount.
  2. loosen the adjustable depth collar until the shaft slides freely.
  3. Raise or lower the motor to the desired depth.
  4. Turn the motor control head to the desired position.
  5. Tighten adjustable depth collar to secure the motor in place.

USING & ADJUSTING THE MOTOR

INSTALLING AN EXTERNAL TRANSDUCER
An external sonar transducer can be installed onto the motor as shown.

MINN-KOTA-PowerDrive-V2-Bow-Mount-Trolling-Motor-8

Note : An external transducer is not included with your trolling motor. Your trolling motor may be pre-installed with a Universal Sonar 2 transducer system. In this case, the transducer is integrated into the motor unit.
For compatibility and more information on Universal Sonar 2, please visit minnkotamotors.com/us2.

ACCESSORY RECOMMENDATIONS:
Minn Kota Transducer Mounting Kit (MKR-15)

USING THE FOOT PEDAL

All the controls in the foot pedal are easy to operate by either foot or hand. A light touch is all that is necessary.

MOMENTARY
A toe touch on the momentary button turns the propeller on. Let up and the propeller stops.

MOMENTARY/CONSTANT (MOM/CON) SWITCH
When the switch is in CON position the motor will run continuously without keeping your foot on the pedal. Slide the switch to momentary (MOM) to again operate the motor with toe touch.

RIGHT/LEFT
Place your foot in the center of the steering pedal, rocking to the right steers right. Rocking to the left steers left. The heel of your foot can also be placed on the deck of the boat. Using your heel to pivot on, depress and hold the
center momentary to turn the motor on or depress and hold the left or right side of the pedal to steer left or right.

NOTE: The steering system is designed to turn your motor 360°. Be careful to avoid over-wrapping the coil cord around the composite shaft.

FORWARD/REVERSE
The propeller always turns in the forward direction. You can reverse the direction of thrust by turning the motor 180˚.

SPEED CONTROL
The speed selector is the calibrated sliding bar located on the right side of the foot pedal. The speed selector provides variable speed control with the built in pulse modulation system. Use your hand or foot to slide the bar forward to increase speed. Draw the bar back to decrease speed. The slider also contains a roller to aid in fine speed adjustment. Slide your foot over the roller with light down pressure to adjust speed. The motor may not start turning until the speed slider reaches speeds 1 or 2. This depends on manufacturing tolerances and if the CoPilot accessory is installed.

NON-CARPETED BOAT USE
Enclosed with your motor are four (4) rubber bumpers. If the foot pedal is to be used primarily on non-carpeted surfaces, insert the rubber bumpers into the keyhole slots on the underside of the pedal. Slide the bumpers into the slot until they are locked into position.

SERVICE & MAINTENANCE

PROPELLER REPLACEMENT

TOOLS AND RESOURCES REQUIRED:

  • Box End Wrench
    • 1/2” for motors with 70 lbs thrust or lower.
    • 9/16” for motors with 80 lbs thrust or higher.
  • Screwdriver (optional)

CAUTION:
Disconnect the motor from the battery before beginning any prop work or maintenance.

NOTE: The propeller on your motor may diff er from the one pictured.

  1. Disconnect the motor from all sources of power prior to changing the propeller.
  2. Hold the propeller and loosen the prop nut with pliers or a wrench.
  3. Remove the prop nut and washer. If the drive pin is sheared or broken, you will need to hold the shaft stationary with a blade screwdriver pressed into the slot on the end of the shaft.
  4. Turn the old prop to horizontal (as illustrated) and pull it straight off . If drive pin falls out, push it back in.
  5. Align the new propeller with the drive pin.
  6. Install the prop washer and prop nut.
  7. Tighten the prop nut 1/4 turn past snug [25-35 inch lbs.] Do not over tighten as this can damage the prop.

GENERAL MAINTENANCE

  1. After use, the entire motor should be rinsed with freshwater. This series of motors is not equipped for saltwater exposure.

  2. The composite shaft requires periodic cleaning and lubrication for proper retraction and deployment. A coating of an aqueous based silicone spray will improve operation.

  3. The propeller must be inspected and cleaned from weeds and fi shing line after every use.
    Fishing line and weeds can get behind the prop, damage the seals and allow water to enter the motor.

  4. Verify the prop nut is secure each time the motor is used.

  5. To prevent accidental damage during transportation or storage, disconnect the battery whenever the motor is off of the water. For prolonged storage, lightly coat all metal parts with an aqueous based silicone spray.

  6. For maximum battery life recharge the battery(s) as soon as possible after use. For maximum motor performance restore battery to full charge prior to use.

  7. Keep battery terminals clean with fi ne sandpaper or emery cloth.

  8. The propeller is designed to provide weed free operation with very high effi ciency. To maintain this top performance, the leading edge of the blades must be kept smooth. If they are rough or nicked from use, restore to smooth by sanding with fi ne sandpaper.

TROUBLESHOOTING & REPAIR

  1. Motor fails to run or lacks power:
  2. Check battery connections for proper polarity.
  3. Make sure terminals are clean and corrosion free. Use fi ne sandpaper or emery cloth to clean terminals.
  4. Check battery water level. Add water if needed.
  5. Motor loses power after a short running time:
  6. Check battery charge. If low, restore to full charge.
  7. You experience prop vibration during normal operation:
  8. Remove and rotate the prop 180°. See removal instructions in the Propeller Replacement Section.
  9. Experiencing interference with your fi shfi nder:
  10. You may, in some applications, experience interference in your depth fi nder display. We recommend that you use a separate deep cycle marine battery for your trolling motor and that you power the depth fi nder from the starting/cranking battery. If problems still persist, call our service department at 1-800-227-6433.

NOTE : For any other malfunctions, visit an Authorized Service Center. You can search for an Authorized Service Center in your area by visiting our Authorized Service page, found online at minnkotamotors.com, or by calling our customer service number at 800-227-6433.

FOR FURTHER TROUBLESHOOTING AND REPAIR

We off er several options to help you troubleshoot and/or repair your product. Please read through the options listed below.
FREQUENTLY ASKED QUESTIONS
We have FAQs available on our website to help answer all of your Minn Kota questions. Visit minnkotamotors.com and click on “Frequently Asked Questions” to fi nd an answer to your question.

CALL US (FOR U.S. AND CANADA)
Our consumer service representatives are available Monday – Friday between 7:00 a.m. – 4:30 p.m. CST at 800-227-6433. If you are calling to order parts, please have the 11-character serial number from your product, specifi c part numbers, and credit card information available. This will help expedite your call and allow us to provide you with the best consumer service possible. You can reference the parts list located in your manual to identify the specifi c part numbers.

EMAIL US
You can email our consumer service department with questions regarding your Minn Kota products. To email your question, visit minnkotamotors.com and click on “Support”.

AUTHORIZED SERVICE CENTERS
Minn Kota has over 300 authorized service centers in the United States and Canada where you can purchase parts or get your products repaired. Please visit our Authorized Service Center page on our website to locate a service center in your area.

PARTS DIAGRAM

POWERDRIVE 45
45 LBS THRUST – 12 VOLT – 48” SHAFT This page provides Minn Kota® WEEE compliance disassembly instructions. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased. Tools required, but not limited to: fl at head screw driver, Phillips screw driver, socket set, pliers, wire cutters.

MINN-KOTA-PowerDrive-V2-Bow-Mount-Trolling-Motor-11

PARTS LIST

POWERDRIVE 45 45 LBS THRUST – 12 VOLT – 48” SHAFT

ITEM QTY PART NUMBER DESCRIPTION
1 1 2-100-204 ARMATURE SEMBLY 12V VARS TXT
2 1 140-010 BALL BEARING
3 1 788-015 R AINING RING
4 1 2-200-079 HOUSING  SEMBLY CENTER 3.25 TXT
5 1 421-132 HOUSING BRUSH END 3.25 TXT
6 1 2-400-187 P IN END HOUSING SEMBLY 3.25
7 1 144-049 BEARING – F NGE (SERVICE ONLY)
8 1 880-003 SEAL
9 1 880-006 SEAL WITH SHIELD
10 2 188-052 BRUSH SEMBLY
12 1 738-030 BRUSH P TE W/HOLDER
13 2 975-032 SPRING – COMPR SION
14 1 701-041 O-RING
15 2 701-007 O-RING, THRU-BOLT
16 1 701-039 O-RING
17 2 830-001 SCREW-8-32
18 2 830-078 THRU BOLT 8-32 X 8.96
19 1 990-067 W HER- EEL THRU
20 2 990-070 W HER – NY TRON
21 1 2069283 MOTOR  SEMBLY 12V 3.25 48”
25 1 2032075 TUBE- RBON COMPOSITE 48”
1 1378121 PROPELLER KIT
26 1 2061122 PROPELLER
27 1 2151726 W HER-5/16 SS
28 1 2053101 NUT-PROP NYLOC
29 1 2092600 PIN-DRIVE
30 1 2301545 COL R-  TCH PD/AP
31 1 2303434 SCREW- 8-32X5/8 MACH PHCR
32 1 2303112 NUT 8-32 NYLOC SS
33 1 2301936 EXTRUSION- B E MACHINED
34 1 2303930 MOTOR R – RIGHT 3-1/4
35 1 2303935 MOTOR R – LE 3-1/4
36 4 2303430 SCREW 1/4-20X5/8 SELF TAP
37 1 2771826 DRIVE HOUSING / TCH HANDLE  SY
1 2882011 BUSHING/ OUTSHA KIT (INCLUD 39-42)
*39 1 2302010 DRIVE HOUSING OUTPUT SHA
*40 2 2307304 BUSHING- INNER
*41 2 2307305 BUSHING- OUTER
*42 1 2304603 O-RING
43 1 2307050 MOTOR- DRIVE HOUSING HIGH SPD
44 1 2307201   TCH HANDLE PD/AP
45 1 2302750 SPRING- TCH TORSION PD/AP
46 1 2302627 PIN- ROLL ZINC
46A 6 2303407 SCREW – DRIVE HOUSING
47 1 2305564 DE L-  OW/DEPLOY
48 4 2305110 PAD-PIVOT SUPT
49 2 2305103 PIVOT PAD- NEW MTR’L
50 1 2300500 PIN- TCH
51 1 2300510 PIN-PIVOT
52 4 2013100 NUT-SPEED
53 1 2303612 ROD-RELE E RT/AP S
54 1 2322700 SPRING-RELE E LEVER
55 1 2303710 LEVER-RELE E
56 1 2300101 RELE E-KNOB
57 1 2301700 SPACER-RELE E LEVER
58 1 2303430 SCREW-1/4-20 X 5/8
59 1 2031522 COL R- DRIVE (W/INSERT)
60 1 2011365 SCREW-COL R/NEW KNOB
60A 1 2323104 NUT
61 1 2304064 CONTROL BOARD SEMBLY- 12V PD
61A 1 2320208 DU PLUG
ITEM QTY PART NUMBER DESCRIPTION
--- --- --- ---
62 1 2355410 SHRINK TUBE-3/8 ODX2
64 3 2303434 SCREW-8-32 X 5/8
65 1 2090651 LEADWIRE LOGA 44”
65A 1 2307310 BEAD – FERRITE (CE MODE ONLY)
66 2 2020700 TERMINAL RING
67 1 2321310  RAIN RELIEF- BRACK PD/AP
68 1 2323405 SCREW-1/4-20 X 5/8
69 1 2306555 HOUSING- CENTER PD/AP
70 1 2074070 BATTERY GAUGE – 12 V
71 1 2316605 DE L, BATTERY GAUGE
72 1 2302935   RAIN RELIEF-DR. HOUSING
73 1 2303960 SIDEP TE (RIGHT)PD MK
74 1 2303965 SIDEP TE(LE )PD MK
75 4 2303430 SCREW-1/4-20 X 5/8
76 1 2302515 CONTROL BOX PD/AP
77 1 2991280 COIL CORD W RAIN RELIEF 48, 54”
1 2991282 COIL CORD W RAIN RELIEF 60”
78 3 2065400 WIRE INSU TOR-LGE
79 1 2256300 TIE WRAP-5” B CK
80 1 2224702 INSERT- PLUG
1 2224700 INSERT- PLUG US2
82 1 2033400 SCREW-10-24 X 1-3/4 PPH Z/P
83 1 2013110 NUT-HEX 10-24 ZCP
86 1 2300237 CONTROL BOX COVER
89 1 2315692 DE L- COVER 45PD
90 4 2012100 SCREW-8-18 X 5/8
1 2994725 FOOT PEDAL SEMBLY
91 1 2304505 FOOT PEDAL B E
92 1 2308501 WEAR P TE FOOT PDL
93 1 2300255 FOOT PEDAL, CORDED UPPER
94 1 2303723 BUTTON, MOMENTARY
95 1 2303722 BUTTON, MOM/CON
96 3 2302730 SPRING-LONG-UPPER PEDAL
98 2302732 SPRING-LOWER PEDAL
99 1 2304052 CONTROL BOARD SEMBLY- PDL
99A 1 2320207 DU  P
100 1 2308620 SLIDER, SPEED
101 1 2308409 MAGN , 1/4 X 1/4
102 1 2778408 MAGN , 1/4 X 1/8
103 1 2300252 COVER, SPEED SELE OR
104 1 2308606 SWITCH, DOUBLE FINGER
105 1 2308608 SWITCH, SINGLE FINGER
106 1 2307900 WHEEL, SPEED
107 1 2308625 SLIDER, EERING
108 9 2302100 SCREW-6-20 X 1/2
109 4 2372103 SCREW-6.20 X 3/8
110 1 2316600 DE L, ON/OFF SWITCH
112 1 2994859 BAG SEMBLY- 4 RUBBER BUMPERS
113 1 2302907   RN RLF PD FP
1 2994864 BAG SEMBLY- (BOLT,NUT,W HERS)
*114 6 2263462 BOLT-MOUNTING-1/4X2 W/ G
*116 6 2261713 W HER-1/4
*117 6 2263103 NUT NYLOK 1/4-20 MTG
*118 6 2301720 W HER-MOUNTING RUBBER
1 2883460 SEAL & ORING KIT

COMPLIANCE STATEMENTS

ENVIRONMENTAL COMPLIANCE STATEMENT:
It is the intention of JOME to be a responsible corporate citizen, operating in compliance with known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products.

WEEE DIRECTIVE:
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle. WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE designed and intended as fi xed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded from the WEEE Directive requirement. This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other household refuse. It must be disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply in the collection, treatment, recovery, and environmentally sound disposal of those products; however, these requirement do vary within European Union member states. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased.

DISPOSAL:
Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements the WEEE directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of your local town council. Never dispose of battery in a garbage bin. Comply with the disposal directions of the manufacturer or his representative and dispose of them at the proper place of collection of your local town council.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MINN KOTA User Manuals

Related Manuals