KOHLER K-1124-GHLA Heated Bubble Massage Air Bath Owner’s Manual
- July 12, 2024
- Kohler
Table of Contents
KOHLER K-1124-GHLA Heated Bubble Massage Air Bath
FAQ
- Q: What should I do if I need to relocate the blower?
- A: Do not relocate or alter the PVC tee or coiled flexible tubing connected to the blower. Follow the blower relocation instructions exactly to ensure proper functioning.
- Q: Is the product ADA compliant?
- A: Yes, the product is ADA compliant when installed according to the specific requirements of ADA regulations.
Features
- 120 airjets release thousands of heated bubbles that surround and support the body in a warm massage
- Automatic and manual purge cycles remove residual water from air channels after use
- Variable-speed blower lets you adjust massage intensity to 18 levels
- Comfort Depth® design offers a convenient 19″ step-over height while retaining the same depth as a standard 21″ bath
- Integral lumbar support
- Slotted overflow allows for deep soaking
- Integral apron
- Integral flange helps prevent water from seeping behind wall and simplifies alcove installation
- Textured bottom surface
- Coordinates with other products in the Archer collection
- Built-in 600W BubbleMassage™ heater warms humidified air before it enters the bath
- Automatic and manual purge cycles remove residual water from air channels after use
Material
- Acrylic
Technology
- Auto-shutoff timer on blower allows users to enjoy Heated BubbleMassage™ experience for 60 minutes before turning off
- User interface: electronic keypad control
Installation
- Left drain
- Alcove
Products/Accessories
Required Products/Accessories
- K-7271 Brass Slotted Overflow Bath Drain
- K-7272 PVC Slotted Overflow Bath Drain
Recommended Products/Accessories
- K-1446 Remote Installation Kit
- K-23726 Drain treatment
- K-23732 Tub & shower cleaner
- K-31797 Slotted overflow bath drain kit
- K-31795 Slotted overflow above-the-floor bath drain kit
Codes/Standards
- ASME A112.19.7/CSA B45.10
- CSA B45.5/IAPMO Z124
- ASTM E162
- ASTM E662
- UL 1795
- CSA C22.2 No. 218.2
- ADA
- ICC/ANSI A117.1
- IAPMO Certification
- UL Listed
Limited Warranty
- KOHLER® Plastic Baths and Shower Bases Lifetime Limited WarrantyKOHLER® Hydrotherapy Components Five-Year Limited Warranty
- See website for detailed warranty information.
Available Colors/Finishes
Color tiles intended for reference only.
Dimensions
Required Electrical Service
Two dedicated circuits required, protected with Class A Ground- Fault Circuit- Interrupter (GFCI). Outside North America, this device may be known as a Residual Current Device (RCD).
- Blower: 120 V, 15 A, 60 Hz
- Heater: 120 V, 15 A, 60 Hz
Technical Information
All product dimensions are nominal.
- Drain location: Left
- Basin area, bottom: 51-3/8″ x 21″ (1305 mm x 533 mm)
- Basin area, top: 64-1/2″ x 30-1/2″ (1638 mm x 775 mm)
- Weight: 120 lbs (54.4 kg)
- Minimum floor load: 42 lbs/ft² (205.1 kg/m²)
- Water depth: 15″ (381 mm)
- Water capacity: 72 gal (272.5 L)
- Electrical component rating:
- Blower: 120 V, 10 A, 60 Hz
- Heater: 120 V, 5 A, 60 Hz
- Minimum flat for door: 2″ (51 mm)
Notes
- Measure your actual product for rough-in details.
- Install this product according to the installation instructions.
- The hot water supply should be 70% of the capacity of the bath or greater. Installations will vary.
- Remote blower installation kit is available for relocating the blower. Provide access for servicing the blower.
- Do not relocate or alter the PVC tee or coiled flexible tubing connected to the blower. Follow the blower relocation instructions exactly.
- ADA compliant when installed to the specific requirements of these regulations.
Contact
- 1-800-4KOHLER (1-800-456-4537)
- Kohler Co. reserves the right to make revisions without notice to product specifications.
- For the most current Specification Sheet, go to www.kohler.com USA or www.kohler.ca Canada
- 6-10-2024 20:00 – US
References
Read User Manual Online (PDF format)
Loading......