MINN KOTA PowerDrive V2 Corded Foot Pedal Instructions

: June 5, 2024
: MINN KOTA

Table of Contents

INSTALLATION OF THE POWERDRIVE V2 / RIPTIDE SP FOOT PEDAL:
FOOT PEDAL CONTROLS:
ENVIRONMENTAL COMPLIANCE STATEMENT:
Documents / Resources

POWERDRIVE V2 / RIPTIDE SP
FOOT PEDAL ACCESSORY

MICROTOUCH FOOT PEDAL
PEDAL MICROTOUCH

Specifications subject to change without notice.

INSTALLATION OF THE POWERDRIVE V2 / RIPTIDE SP FOOT PEDAL:

Remove protective covers from both connectors ends.
Align connector keys and plug the foot pedal into the Powerdrive V2 or Riptide SP motor. Be sure to tighten the connector retaining nut.

NOTICE: DO NOT APPLY LUBRICANT OR ANY TYPE OF GREASE TO TROLLING MOTOR CONNECTORS

FOOT PEDAL CONTROLS:

All the controls in the foot pedal are easy to operate by either foot or hand. A light touch is all that is necessary.

Momentary. A toe touch on the “momentary on” pedal turns the motor on. Let up and the motor stops.
Mom/Con Switch. When the switch is in the CON position the motor will run continuously without keeping your foot on the pedal. Slide the switch to momentary (MOM) to again operate the motor with a toe touch.
Right/Left. Place your foot in the center of the steering pedal, rocking to the right steers right. Rocking to the left steers left. The heel of your foot can also be placed on the deck of the boat. Using your heel to pivot on, depress and hold the center momentary to turn the motor on, or depress and hold the left or right side of the pedal to steer left or right.

NOTE: The steering system is designed to turn your motor 360°. Be careful to avoid over-wrapping the coil cord around the composite shaft.

Forward/Reverse. The motor always drives forward by depressing the foot pedal. You can reverse the direction of thrust by turning the motor 180°.
Speed Control. The speed selector is the calibrated sliding bar located on the right side of the foot pedal. The speed selector provides infinitely variable speed control with the built-in pulse modulation system. Use your hand or foot to slide the bar forward to increase speed. Draw the bar back to decrease speed. The slider also contains a roller to aid in fine speed adjustment. Just slide your foot over the roller with light down pressure to adjust speed. The motor may not start turning until the speed slider reaches speeds 1 or 2. This depends on manufacturing tolerances and if the CoPilot accessory is installed.
Non-Carpeted Boat Use. Enclosed with your motor are four (4) rubber bumpers. If the foot pedal is to be used primarily on non-carpeted surfaces, insert the rubber bumpers into the keyhole slots on the underside of the pedal. Slide the bumpers into the slot until they are locked into position.
Control Cord. The foot pedal cord is flexible and long enough to allow the pedal to be positioned almost anywhere on your boat.

CAUTION: SWITCH THE MOM/CON SWITCH TO MOM WHEN NOT IN USE. IF THE MOTOR CONTROL IS LEFT ON AND THE PROPELLER ROTATION IS BLOCKED, SEVERE MOTOR DAMAGE CAN RESULT.

ENVIRONMENTAL COMPLIANCE STATEMENT:

It is the intention of Johnson Outdoors Inc. to be a responsible corporate citizen, operating in compliance with known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products.
WEEE Directive:
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE designed and intended as a fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded from the WEEE Directive requirement.
**** This symbol (WEEE wheelie bin) on a product indicates the product must not be disposed of with other household refuse. It must be disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply with the collection, treatment, recovery, and environmentally sound disposal of those products; however, these requirements do vary within European Union member states. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased.

Johnson Outdoors Inc.
Visit our website athttp://www.minnkotamotors.com
p/n 2377124 REV. D ECN 32280