3nStar SC610BT Industrial Wireless Barcode Scanner User Manual
- June 10, 2024
- 3nStar
Table of Contents
3nStar SC610BT Industrial Wireless Barcode Scanner User Manual
Product Description
- Barcode Scanner
USB Connection Method
- Connect the PC/POS with USB cable.
RS232 connection method
- Connect the PC/POS with RS-232 cable. Connect the power adapter to the socket, and connect the power supply cable to the base.
With Base Pairing Method
To pair the scanner with the wireless base, follow thesteps below: (!)Connect the base to the computer; @Press the scan button to start the scanner, and place the scanner on the base for pairing
.After the pairing is successful, there will be an indicator tone, the scanner’s green light will stay on.
®If the base cannot be paired normally, use the scanner to scan the pairing code on the bottom of the base, and then reposition the scanner on the base, waiting for a successful audible and visual indication.
Product Description
Base cable plug
Cable insertion:
Connect the cable in the direction shown in the picture.
**
unplug the cable:
Press the buckle first as shown in the picture, Then unplug the cable.
Bluetooth HID Pairing Method
U se the scanner to pair with mobile phone/computer and other devices, please follow the steps below:
- Use the scanner to scan the “Bluetooth HID Pairing Code” below. If Bluetooth is not paired for more than one minute, it will automatically shut down and give a three-tone prompt.
- Open the Bluetooth device to search for the Bluetooth name “Barcode Bluetooth HID”, and then click Pairing.
- After the pairing is successful, the scanner’s green indicator is always on and there is a prompt tone.
Battery Install & Remove
-
Rotate the bottom screw In the direction shown in the picture, and loosen the screw.
-
Open the bottom.
-
Remove/insert battery.
-
Tighten the screws in the direction shown to lock the bottom.
Scanning Method &Scanning Distance
- Scanner aim at the center of the barcode.
It is better to maintain a certain angle between the barcode and the scanner.(Aiming light is subject to actual product)
• If the bar code is highly reflective,pls try rotate scanning at a certain
angle instead of scanning vertically.
Charging Method
-
One battery: charge the scanner through the base.
-
Two Batteries: Charge the battery and the scanner simultaneously through the charging base. (Base need to connect with power supply cable)
Working status (base)| Base Indicator Light Prompt| Buzzer
Prompt
---|---|---
Base power on| Yellow light on| A low short tone
Scanner successfully connected to the base| Green light on| N
Scanner disconnect from base| Green breathing light status| N
Data has been transferred| Green light flashes one time| A low short tone
Scanner is on charging| Blue light on| N
Scanner fully charged| Yellow light on| N
Working status (backup battery compartment)| Battery charg ingindicator prompt
---|---
The battery is charging| Two blue indicators are always on
The battery is fully charged| Three yellow indicators are always on
**Use The Base Flat Mode
Flat Mode
Wall mounted mode
**
After the wall mounted switch Is turned on, the scanner can be placed on the base without falling
Qusestion 1: The scanner does not work.
Answer: The battery may not be charged. Solution: Place the scanner into
the base to charge or replace the battery.
Question 2 : The scanner does not upload data. (there is no prompt of
successful barcode reading)
Answer: The reading of the corresponding barcode type is not enabled.
Solution: Turn on the reading of the corresponding barcode type.
Answer: The barcode is damaged, distorted and deformed, resulting in
unreadable.
Solution: Make sure the barcode is not damaged, twisted or deformed.
Answer: The distance between the scanner and the barcode is incorrect.
Solution: Move the scanner closer or away from the barcode.
How To Use The Wall Mounted
Question 3: The scanner does not upload data. (there is a prompt of
successful barcode reading)
Answer: The host interface configuration is incorrect.
Solution: Scan the corresponding host interface parameter barcode to set.
Answer: The scanner has not been paired with the base.
Solution: Follow the pairing method to pair with the base.
Answer: Beyond the effective transmission distance.
Solution: Ensure that the scanner and the base are. within the effective
communication distance. Answer: The cable is loose or damaged.
Solution: Make sure that the cable has been connected and fixed. If you
still cannot upload data, please contact after-sale service.
Question 4: The data is incorrectly displayed on the host.
Answer: The input language is incorrect.
Solution: Set the correct scanner language
Answer: The host interface configuration is incorrect.
Solution: Scan the corresponding host interface parameter barcode for
setting.
Answer: The zone configuration is incorrect.
Solution: Choose the corresponding country/region and language coding
scheme.
Indicator Light & Buzzer Status
Working Status (Barcode Scanner)| Indicator Light Prompt| Buzzer
Prompt
---|---|---
Power on| Green light on| A long treble
Waiting for pairing connection| Green light flashes continuously for 60s| Two
high low short tones
Scanner successfully connected to the base| Green light on| A low short tone
Scanner successfully connected to Bluetooth device| Green light on| A low
short tone
Read Barcode Successfully| Green light flashes| A medium long treble
Scanner charging| Blue light on| N
Scanner standby| N| Two high low short tones
Alarm prompt or disconnection| Green light flashes| Three tone continuous
short tone
Precautions
- Charge the battery fully before using the barcode scanner for the first time.
- Do not point the scanner light at the eyes directly
- Use the original charger to charge the batteries
- Avoid contact with metal objects (such as keys, etc.) with the battery electrodes or an artificial short circuit of the battery electrodes.
- Do not place the battery in an overheated, humid or corrosive environment, and do not squeeze or hit it.
- If the battery is swollen, replace it.