JBC DIU 1 Tool Control Unit Instruction Manual
- June 5, 2024
- JBC
Table of Contents
JBC DIU 1 Tool Control Unit
Packing List
The following items are included:
Features
For a basic working system, 1 control unit + 1 stand + 1 tool and 1 cartridge
are needed.
Connection Example
General Purpose Handle
Desoldering Iron
Compatibility
Select the equipment that best suit your soldering or desoldering needs.
Operation
The JBC Most Efficient Soldering System
Our revolutionary technology is able to recover tip temperature extremely
quickly. It means the user can work at a lower temperature and improve the
The tip temperature is further reduced thanks to the Sleep and Hibernation
modes ncrease up to 5 times the life of the tip.
-
Work
-
Sleep
-
Hibernation
Control Process
Work Screen
Menu Screen
USB Connector
Download the latest software from our website to improve your soldering station.
JBC Updater
www.jbctools.com/software.html
Update the station software via USB connection: 
JBC Web Manager Lite
www.jbctools.com/manager.html
Manage and monitor as many stations as your PC can handle by using JBC Web
Manager Lite. Data can be exported to another PC. 
Maintenance
Betore carrying out maintenance, always Switch the device off and disconnect
it from the mains. Allow the equipment to cool down.
- Clean the station screen with a glass cleaner or a damp cloth.
- Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
- Periodically check that the metal parts of the tool and stand are clean so that the station can detect the tool status.
- Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation.
- Rusty and dirty surfaces reduce heat transfer to the solder joint.
- Periodically check all cables and tubes.
- Replace any defective or damaged pieces.
- Only use original JBC spare parts.
- Repairs should only be performed by a JBC-authorized technical service.
Replace a blown fuse as follows:
- Pull off the fuse holder and remove the fuse. If necessary use a tool to lever it oft.
- Insert the new fuse into the fuse holder and return it to the Station.
Safety
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause a fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflammable products to ignite.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Specifications
DIU 1-Tool Control Unit
DI-1D 120V 50/60Hz. Input fuse: T2A. Output: 23.5V.
DI-2D 230V 50/60Hz. Input fuse: T1A. Output: 23.5V.
DI-9D 100V 50/60Hz. Input fuse: T2.5A. Output: 23.5V.
- Output Peak Power CD-BE:
- Temperature Range:
- Idle Temp. Stability (still air):
- Tip to Ground Voltage/Resistance:
- Ambient Operating Temp:
- Connections:
- Control Unit Dimensions / Weight:(L x W x H) 130W
- 90 – 450 °C / 190 – 840 °F (±5%)
- ±1.5 ºC / ±3 ºF
- Meets and exceed
- ANSI/ESD S20.20-2014 IPC J-STD-001F 10 – 40 ºC / 50 – 104 ºF
- USB-B / Peripherals connectors
- 180 x 94 x 106 mm / 2.153 kg
- 7.10 x 3 .70 x 4.17 in / 4.75 lb