inateck SA02003 USB 3.0 Dual SATA HDD Docking Station Instruction Manual

: June 5, 2024
: inateck

Table of Contents

Introduction
Overview
How to Use
Technical Specifications
Package Contents
Troubleshooting/FAQ
Service Center
Read User Manual Online (PDF format)
Download This Manual (PDF format)

inateck SA02003 USB 3.0 Dual SATA HDD Docking Station Instruction Manual

Introduction

This product support data copy and clone between dual HDDs.
Meanwhile, it adopts USB3.0 (Super Speed) with date transfer rate up to 5Gbps and SATA3 (6Gbps) and backward compatible with earlier versions as well. This excellent transmission performance and good compatibility is convenient for data exchange and perfectly suitable for the men who need to batch processing and clone data at some certain places, such as film and television production, Backup & processing IT data, Schools batch processing data etc

Overview

How to Use

Connect the external power adapter from the hard drive dock to an electrical outlet.
Connect the included USB 3.0 cable from the hard drive dock to an available USB port on the computer system.
Insert a 2.5” or 3.5” hard drive into the top loading slot.
Press the power button. A pop-up bubble in the task bar at the bottomright of your screen notifying you once your hard drive has been recognized. You may also find the hard drive in Disk Management.

Note:

To remove the hard drive, make sure it is currently not being accessed by the computer then unmount or uninstall the disk drive from the operating system. Never remove the docking station while the hard drive is in use. Doing so may corrupt the data on the hard drive or damage the hard drive, docking station, or computer.
When connected via USB, the dock will automatically go into sleep mode if the connection is left idle for more than 30 minutes. The power LED indicator will always be on and the colorful atmosphere light at the bottom will enter the slow flashing state. Accessing the hard drive will automatically cancel sleep mode and power the drive back up.
The hard drive LED indicator will flash, the power LED indicator will be constantly on and the bottom colorful atmosphere light will enter the fast flashing state.
Please do not remove your hard drive or insert a new one while the other hard drive is being accessed, as doing so the other drive temporarily disconnects and this could damage your hard drive and result in data loss.

Hard Drive Offline Clone

Make sure there are no connection on the USB.
Insert the drives straight down until the connection is secured. Offline clone is from HDD A to HDD B. Make sure your Main Drive is in HDD A and slave in HDD B. The capacity of HDD B must be equal or bigger than HDD A.
Press and hold the offline button for 3 seconds, the LED indicator that marks 100% clone progress will light up. Quickly press the button again, and offline clone starts. 4 LED lights indicate the clone progress.
One by one they will flash and be on. When the offline clone is 100% completed, 4 LED lights will stay on.

Technical Specifications

Product Name	USB3.0 Dual SATA HDD Docking Station with Offline Clone Function
Model Number	Inateck SA02003
Weight	410g

Package Contents

SA02003 Docking Station × 1
USB 3.0 Data Cable × 1
DC Power Adapter × 1
Instruction Manual × 1

Troubleshooting/FAQ

Unable to clone: Please check if the capacity of Disk B is larger or equivalent to that of Disk A. Here the capacity means the actual capacity that can be used, instead of the one marked on the product.For example, the actual capacity of a disk marked 500GB might be 480GB only. The actual capacity of disks with the same marked capacity differs if they are produced by different producers. To ensure two disks of the same marked capacity have the same actual capacity, they should be produced by the same producer in the same batch with the same model number.
Indicator light stops flashing up during offline duplicating: it might because of disk bad sectors so that data couldn’t be cloned as usual.
It’s better to change a good disk.
After cloning, the rest capacity of B disk is showed and operated via “Computer management – Storage – Disk management”.
Why over 2TB hard disk couldn’t be identified by USB? Because the maximum capacity of hard disk which Windows XP can supports is 2TB and couldn’t be identified by system if over 2TB. It only supports after upgrading the operating system above Vista (64 bit) version and we suggest changing hard disk into a GPT disk partition, or the operating system will not support over 2 TB disk partitions.
Please make sure that B hard disk data can be covered before cloning data. Because once you start cloning, B hard disk partition methods and data are completely cloned as A hard disk. Our company does NOT undertake any responsibility for data or economy loss which could bring by damaged data.
Please do not remove your hard drive or insert a new one while the other hard drive is being accessed, as doing so the other drive temporarily disconnects and this could damage your hard drive and result in data loss.

Service Center

Europe
F&M Technology GmbH
Tel: +49 341 5199 8410 (Working day 8 AM – 4 PM CET)
Fax: +49 341 5199 8413
Address: Fraunhoferstraße 7, 04178 Leipzig, Deutschland

North America
Inateck Technology Inc.
Tel: +1 (909) 698 7018 (Working day 9 AM – 5 PM PST)
Address: 2078 Francis St., Unit 14-02, Ontario, CA 91761, USA

日本
Inateck 株式会社
電話番号：+81 06 7500 3304
〒 547-0014 大阪府大阪市平野区長吉川辺 3 丁目 10 番 11 号

Importer/Responsible Person:

Europe
F&M Technology GmbH
Fraunhoferstraße 7, 04178 Leipzig, Deutschland
Tel: +49 341 5199 8410

UK
Inateck Technology (UK) Ltd.
95 High Street, Office B, Great Missenden, United Kingdom, HP16 0AL
Tel: +44 20 3239 9869

Manufacturer
Shenzhen Licheng Technology Co., Ltd.
Address: Suite 2507, Block 11 in Tian An Cloud Park, Bantian
Street, Longgang District, Shenzhen, Guangdong, China