LYKYL

LYKYL Professional Hair Clipper

Specifications

• RECOMMENDED USES FOR PRODUCT: Barber, Trimming, Professional
• ITEM WEIGHT: 1000 Grams
• BRAND: LYKYL
• POWER SOURCE: Battery Powered, Electric
• MATERIAL: Metal
• BLADE MATERIAL: Carbon Steel
• COLOR: Rose Gold
• POWER: 5W
• VOLTAGE: 110v-240v
• BATTERY: 2000mAh
• CHARGING TIME: 3 Hours
• USE TIME: 300 Minutes
• SIZE: 17*4.5cm
• TOOTH PITCH OF CUTTER HEAD: Adjustable

Introduction

Display power on an LED digital display and check power at any time. It has Carbon Steel Cutter Head, Strong Power, Quick And Efficient Haircut, Not Easy To Get Stuck; Long-lasting battery life and a large capacity. Plugging In And Charging With Power Supply Fast haircut, low noise, professional noise reduction, and labor savings.

HOW TO MAINTAIN CLIPPER ATTACHMENTS

Don’t use any attachments that you haven’t removed. Remove as much hair and dirt from your clippers as you can with a cleaning brush. To remove any remaining hair and avoid cross-contamination, use an antibacterial clipper spray. Before wiping clean, let the spray sit for the amount of time specified on the can.

HOW TO CLEAN CLIPPER HEAD

Make sure the grooming device is off. Use your cleaning brush to remove any hair or skin buildup after removing the tool’s head. If the head cannot be removed, you can brush the blade region. Rinse the head under the faucet to remove any extra skin, hair, or oil.

HOW TO REMOVE A CLIPPER GUARD

Most clipper guards are rather simple to remove. Pull the guard off by pulling down on the tab. It is significantly simpler to clean as a result. Before removing the protection, make sure the clipper is turned off and unplugged to prevent accidently starting it.

HOW TO STORE CLIPPERS

While you can store your clipper with a blade still attached, it may be advisable to remove the blades and wrap them in an oiled towel to avoid rusting. Spraying your blades with the Andis 5-in-1 cooling spray before storing them will provide them extra protection because it has rust- preventative qualities.

HOW TO TEST CLIPPER BLADES

Try to move the top cutter of the clipper from side to side while holding the blade in your palm. If you discover that the top cutter is not moving far enough, you should loosen the tension a little. To accomplish this, insert a flat-head screwdriver into the spring’s side and slowly release the tension.

Frequently Asked Questions

Should guys use clippers on dry or damp hair?****

Don’t even try to trim dripping wet hair with clippers; it’s practically impossible. A good towel dry makes it much simpler for you to achieve the desired style and helps keep the clipper blades from rusting.

Can clippers be used without a guard?****

Using electric razors without the clipper guard is absolutely acceptable. Just remember to rinse off the extra hair from your face after shaving, then use a tonic or after-shave product and moisturizer.

How do the sizes of hair clippers work?****

Since many of the lower guard numbers are utilized in fades, the shorter the guard number, the shorter the hair will be. If you request a fade, you’ll get bonus points for knowing which guard number you want to fade from and into.

Can skin be sliced by clippers?****

The blades are acute. However, under typical use, factory-set clipper and trimmer blades shouldn’t sever the skin. However, keep in mind that dropping or striking the blades can cause them to become misaligned and lead to skin nicks.

Can a clipper blade be washed?****

Usually, cleanings for clipper blades disinfect. However, if the product isn’t designed to disinfect, follow these additional procedures using a little alcohol: After cleaning it out or getting a new one, add some alcohol to the dish. Your blades should be submerged for 10 to 20 seconds before being removed to be dried with a delicate microfiber cloth.

Are clippers harmful to hair?****

“Scissors allow the hair to grow back better and more smoothly than clippers, which gives your hair a better texture. Clippers can harm the hair and make it look spiky. Simply put, the hair sits better. Additionally, getting a haircut is a peaceful experience because scissors are plainly quieter than clippers.

How short are your haircuts with clippers?****

In general, the cut is shorter the lower the number. For instance, a “0” will result in hair that is hardly noticeable, whereas a “8” is one inch (25 mm). Starting with 1/8 inch (3.2 mm) for number “1,” the blade guards increase by an eighth of an inch (3.18 millimeters) for each number in between.

How much time do clipper guards last?****

The guards are available in the following sizes: 1/16″, 1/8″, 3/8″, 1/2″, 5/8″, 3/4″, 7/8″, 1″, left ear taper, right ear taper, eyebrow, and ear trim guides. This is what? They typically range in size from 1/8″ to 1″.

A 1 guard is how long?****

Sizes of Oster clipper guards

Which produces more haircuts, open or closed?****

The blade is in its lowest cutting position when the taper lever is closed, which results in more hair being chopped. The blade is at its longest cutting position while the taper lever is open, cutting the least amount of hair. The majority of common clipper blades are configured 000 to 1 without a zero gap.

What is the hair clippers’ longest setting?****

Among all clipper lengths, the number 8 haircut typically has the greatest haircut number. You can utilize the inch-long hair it leaves behind to fade the sides with a smaller hair clipper while using it to trim the top.

Which hair clipper attachment has the longest blade?****

On Oster clippers, hair clipper guards are typically available in three sizes. The smallest is the mini/size 1, measuring about 1/16 inches. The most popular size is #2, which is 1/4 inch in length. The longest size is #10, measuring 1-1/4 inches.

Why won’t my hair clippers cut?****

Apply two drops of clipper oil to the blades and test cut again as soon as your blades begin to pull hair. (Oil lubricates the blades so they can cut effectively and run at the proper pace. The clipper runs cooler as a result.

How do you use clippers to cut hair on the sides?****

Trim the sides from the bottom to the top using the blade’s edge. As you try to get a consistent fade with the remainder of your hair, tilt the clipper blade at an angle. Before going to the rear, repeat this procedure on the opposite side of your head, ensuring sure that each side is even as you proceed.

How come my hair clipper is so loud?****

My mains-powered clipper makes a loud noise when I try to clip. This indicates that either the power screw on the right side of the clipper needs to be adjusted or the blades need to be oiled.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>