GoldenEar Invisa Series Invisa SP 652 StereoPointTM One Piece Stereo In-Wall/In-Ceiling Loudspeaker Owner’s Manual

Invisa® Series
Invisa SP 652 StereoPoint™ One Piece Stereo In-Wall/In-Ceiling Loudspeaker
Owner’s Manual

Congratulations!
Congratulations and thank you for purchasing GoldenEar’s™Invisa® speakers! You are about to hear the spectacular difference these very special In-Wall/In- Ceiling speakers will make in your home’s music system!

Our engineers’ many years of experience in developing loudspeakers has led to these extraordinary products. In order to ensure that you experience maximum performance, please take a moment to fully read this owner’s manual and familiarize yourself with the unique installation, assembly, and set-up procedures for your Invisa® speakers.

Please visit our website at www.GoldenEar.com for more information on the technology behind your new speaker system. If you have additional questions, contact your Authorized GoldenEar™ Dealer or visit the Q&A page in the Tech Support section of our website.

Your New GoldenEar Speakers

GoldenEar Invisa® SP 652 in-ceiling/in-wall speakers are designed to fit beautifully in a wide variety of applications. Their low-profile grille and nearly invisible design allow for perfect integration in a wide variety of locations within your home. To get the best performance possible and for a product that lasts a lifetime, we strongly recommend that you follow the placement and setup guidelines provided in this manual.

Cleaning
Do not use a strong or abrasive cleaner on your new speakers’ grilles. Clean them only with a damp cloth, but do not get them wet.

Preventing Speaker Damage

**** USE AN APPROPRIATE AMPLIFIER. At high volumes, a very powerful amplifier can overdrive your speakers and damage them. And if the amplifier is not powerful enough, it can produce distortion that can easily damage your speaker. (Consult your dealer for assistance.)

**** DON’T BE FOOLED BY THE VOLUME CONTROL. It only adjusts how loud, it is not an indication of power output. If your speakers begin to sound harsh or grating or if you hear other forms of distortion, turn down the volume immediately!

**** Avoid the use of tone controls and loudness controls as they will demand even more power from an amplifier, lowering the volume at which damage could occur.

GoldenEar Invisa® speakers are efficient and can be driven to loud listening levels with moderate amplifier power.
They are also able to handle the output of very powerful amplifiers. To prevent damage to your speakers, please read all of the following guidelines before hooking them up.

Amplifier Distortion — #1 Threat to your New Speakers!
Amplifier distortion is the principal cause of speaker damage. When listening to loud levels your amplifier may run out of clean power. It will then begin to produce speaker-damaging distorted power. This will damage any brand of the speaker very quickly! More powerful amplifiers are actually safer — For example, A 40 Watt/channel amplifier will have substantial distortion above 40 Watts. If driven to 50 Watts, this amplifier will deliver speaker-damaging distorted power! But a 100 Watt/channel amplifier will have very low distortion below 100 Watts. Therefore, when the speaker requires 50 Watts, this more powerful amplifier will deliver clean power and speaker damage is less likely to occur. (See your GoldenEar dealer for amplifier recommendations.)

Room Acoustics
GoldenEar Invisa® speakers are designed to provide exceptional sound in a wide variety of domestic settings. It is important to note however that listening room construction, dimensions, and furnishings all play a part in the quality of sound you will ultimately achieve from your new speakers. The listening room will impose its own character on the performance capabilities of the speaker system. Regarding the room, please note that:

• Mid and high frequencies are affected by the amount of soft furnishings in your room — curtains, carpets, sofas, wall coverings, etc. An excess of such items can result in a somewhat dull sound. The same room without any soft furnishings can produce an overall bright sound. The typical quantity of soft furnishings found in most living environments provides the right acoustic characteristics to allow the speakers to sound balanced;
• Concrete floors and walls tend to aggravate low-frequency standing wave problems and are less preferred;
• Rooms, where height, width, and length are similar, should be avoided as they can exhibit significant low-frequency standing wave problems. This may result in reduced clarity. In such rooms avoid corner placement to minimize acoustic problems.

The extra care you take in correctly positioning the speakers will result in greater listening enjoyment. So, keep the following guidelines in mind when deciding on the best speaker placement.
To ensure the best performance possible, observe the following placement guidelines:

LOCATION: When preparing to install your speakers pick a location that has the required clearance between wall studs or ceiling joists. Make sure to check for wiring, conduit, water pipes, HVAC ducts, and other obstructions before cutting the installation hole.

ACCURATE TIMBRE: For the most accurate and natural timbre, in-wall speakers’ high-frequency drivers should be at approximately ear level. Select locations that allow the sound to reach the listening area unobstructed by furnishings.

BALANCED BASS: Placing speakers in corners will over-emphasize bass and reduce overall clarity. If possible, position speakers away from sidewalls. This will ensure better bass performance and optimal midrange clarity.

SINGLE SPEAKER LEFT + RIGHT STEREO SOUND: The Invisa SP 652 is ideal for smaller areas not suited to a stereo pair of speakers, or where a single speaker is a preferred choice. Position the speakers to achieve the best sound coverage for the room. See figure below)

The Invisa SP 652 can also be used in large areas for distributed audio where any “pair” of speakers would not be heard as a stereo pair (see figure below).

Speaker Break-in
Your new Invisa® loudspeaker system should sound good as soon as you turn them on; however, an extended break-in period of 40-60 hours or more of normal playing time is required to reach full performance capability. Break-in allows the driver suspensions to work in and crossover components to “heal,” resulting in fuller and tighter bass, a more open “blossoming” midrange, and smoother high-frequency reproduction.

Color-Match Painting (optional)

Your new Invisa in-wall/in-ceiling speakers include a paintable “edgeless” grille that completely covers the installed speaker. The grille comes in a neutral white to blend with most areas, however, for the ultimate in “stealth” installation, they may be painted to match any decor. PLEASE NOTE: Failure to follow the instructions below may result in serious degradation of sound quality!

Please Note:

• Do not paint the grille with a brush or roller — this will clog the grille’s acoustic perforations and muffle the sound.
• It is not necessary to remove the backing cloth, or scrim, from the grille before painting.
• Do not heat cure the finish.
• Do not paint the grilles while attached to the speaker.

To paint, follow these steps:

1. Remove the grille from the speaker and place it on a drop cloth

2. Spray paint the grille using:
   i. A spray paint that closely matches the color and shines desired
   ii. A custom-made spray can, color-matched to your paint finish
   iii. The indoor latex paint used to paint the ceiling or wall but diluted to the paint manufacturer’s/ spray gun manufacturer’s recommendations

3. In a well-ventilated area, apply several light coats of paint, sprayed at about a 60-degree angle from the grille’s surface, letting the grille dry completely between coats. Follow the paint manufacturer’s directions.

4. To ensure the paint is evenly applied, each coat should be applied from multiple directions (at least four).

5. Once the painted grille has dried completely, if necessary you can use a brush or small roller to touch up the grille’s outer edge — just be careful not to get any additional paint on the grille’s perforated surface.

Installation Instructions

Installation of your new Invisa® speakers requires the use of tools such as a drill, screwdriver, saws, and possibly other power tools. The installer should have knowledge of all applicable building and/or fire codes. Care must be taken to ensure the area behind the wall or ceiling where you plan to install the speakers is clear of obstructions. When cutting the hole in and running wires through walls and/or ceilings proper care must be taken to avoid electrical, water, gas, and/or HVAC pipes and the corresponding risks to your safety and risk of damage to property.
If you are not comfortable with the above and/or performing the following installation procedures we strongly suggest having a professional contractor install your speakers (see your GoldenEar Dealer).

Tools Required:

• Pencil
• Drywall saw, Keyhole saw, utility knife, or another material-appropriate cutting tool for wall material
• Phillips Head Screwdriver
• Power drill with an appropriate bit (optional, for starting wall cut)

Installation Into Existing Walls or Ceilings

For new construction (pre-drywall), use our custom rough-in brackets, sold separately.

NOTE: You must first install appropriate gauge and type speaker wires. For best sound quality, the use of a high-quality speaker cable is essential.

1. Make sure the wall material can support the weight of the speakers you plan to install (see specifications page for weights).

2. Make sure the location selected is free of studs, electrical wiring, water or gas pipes, etc. Prior to installing, hold the speaker in your selected location to make sure it is clear
   of any obstacles. PLEASE NOTE: Your cutout must be at least 2″ (50mm) from adjoining walls/ceiling, internal studs, and any pipes.

3. Place the included mounting template onto the wall or ceiling in your preferred location. Use the pencil to trace around the template (Figure 1).

4. Carefully cut a hole with the appropriate cutting tool along the pencil trace as follows: Start the hole by drilling a hole inside of the pencil line (place drill bit just inside the line). Use this hole to insert the cutting tool and begin cutting — be careful not to cut outside the template line! (Figure 2).

5. For In-Wall Mounting:
   • For optimum performance, loosely place two pieces of standard fiberglass insulation in the wall, one just above the hole and one just below. An 8″ x 10″ piece should work well, R-12 for a 2×4 wall, R-20 for a 2×6 wall.
   • Also place a half-thick piece of fiberglass insulation cut to the height of the speaker in the wall right behind the mounting hole.

6. For In-Ceiling Mounting:
   • For optimum performance, loosely place one piece of standard fiberglass insulation, cut to fit the joist size, above the speaker and extending about 15″ or more beyond the speaker;
   • For taller joists, also place fiberglass insulation against the joists on either side of the mounting hole.

7. Pull the speaker wire out of the hole and connect the speaker as follows:
   • Your Invisa® speakers are equipped with a set of four high-quality push spring connectors that can be used with bare wire. Make sure all wires are firmly fastened. Always use a high-quality speaker wire of the correct rating (see above) and a sufficient gauge for the distances you are running (see your dealer for assistance).
   • Strip 1/2″ (12 mm) of insulation from each of the two conductors to expose the metal, twist the strands of each into two single un-frayed strands. Repeat for the other channel’s two conductors.
   • Hold the speaker up to the cutout and connect the speaker cables. Proper polarity (or phase) is critical for proper stereo imaging and bass performance. Connect the left channel’s red(+) terminal of your receiver or amplifier to one of the red(+) terminals of the Invisa loudspeaker and the left black(-) terminal of your receiver or amplifier to the adjacent black(-) terminal of the Invisa loudspeaker. Repeat for the right channel and the other set of convectors on the Invisa speaker. (See Figure 3). Most speaker cables are either color-coded or have some indicator (ribbing or writing) on one of the conductors to help maintain this consistent polarity. It is essential that the speaker be connected in the same way (in-phase) to its own channel of the amplifier.
   • Push down on the top of the speaker’s push terminal to reveal the wire hole in the post. Insert the wire into the hole and release your pressure on the terminal. Repeat for all four connections.

8. Loosen the four rotating lock arms on the speaker by turning the arm screws on the front of the speaker counterclockwise 1/2 to 1 turn, just enough to allow the lock arm to move freely (Figure 4). • Make sure the rotating lock arms are positioned inwards (Figure 5) so that your speaker fits into your cutout hole.

9. Holding the speaker’s front lip with your thumbs and index fingers, carefully slip the speaker into the cutout and hold it firmly in place. (Figure 6).

10. While holding in place, tighten the four lock arm screws with a screwdriver (Figure 7). This will rotate the lock arms and secure the speaker to the wall/ceiling. DO NOT OVERTIGHTEN the lock arm screws as this could damage the drywall. If you are using a power screwdriver or drill, set the torque to a value of no more than 7 in.-lb (8dN-m).

11. Install the grille by placing it over the installed speaker and aligning the powerful miniature magnets.

Setting the Invisa Speaker’s High-Frequency EQ Control (HF EQ Switch)
We suggest starting with the HF EQ control (Figure 8) in the “+” position, in typical rooms with a balance of reflecting and absorbing surfaces. If, however, your listening room is overly “bright” due to many reflective, hard surfaces, select the center position to effectively compensate for this type of room acoustics issue. If the sound in the listening position is still too bright, select the “-” position to compensate further.

Adjusting the Rotating Tweeter

The Invisa® SP 652 speaker incorporates a rotating tweeter assembly to allow for easy orientation of the tweeter assembly after installation. To rotate the assembly for best results: With the speaker installed and the grille off, rotate the tweeter assembly so that the bars/slots are horizontal when viewed from the listening position (See Figure 9).

Troubleshooting

If you experience any difficulties with your Invisa® speakers, try the suggestions described below. If you are still having problems, please consult your GoldenEar Authorized Dealer for assistance.

1. Make sure all your system interconnects, speaker cables and power cords are solidly in place.
2. Check that no foreign objects or liquid have entered the speaker.
3. If no sound comes out or the sound is distorted in some way and you are sure the system is set up properly, please bring the speaker to your GoldenEar Authorized Dealer for assistance. But make sure you call first.

Service
Service and warranty work on your GoldenEar loudspeakers will normally be performed by your local GoldenEar dealer. If, however, you wish to return the speaker to us, please contact us first, describing the problem and requesting authorization as well as the location of the nearest factory service center. Please note that the address given in this booklet is the address of our office only. Under no circumstances should products or parts be shipped to our offices or returned without contacting us first and obtaining return authorization.

The Quest Group dba
GoldenEar™
2621 White Road
Irvine, CA 92614 USA
Phone: 949-800-1800

Technical assistance

It is our pleasure to offer assistance if you have any questions regarding your Invisa® speakers or their setup.
Please contact your nearest GoldenEar dealer or contact us directly at 949-800-1800.

Recycling and Reuse Guidelines for Europe

In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we would like to notify you that this product may contain regulated materials which, upon disposal, according to the WEEE directive, require special reuse and recycling processing. For this reason, GoldenEar (manufacturers of GoldenEar speakers) has arranged with our distributors in European Union member nations to collect and recycle this product at no cost to you. To find your local distributor please contact the dealer from whom you purchased this product or go to our website at www.goldenear.com.

Please note that the product only falls under the WEEE directive. When disposing of packaging and other shipping material we encourage you to recycle through the normal channels.

Specifications

Invisa® SP 652

Two HVFR™ High Velocity Folded Ribbon tweeters
Rec. Application:| 10 – 125 Watt/channel

Specifications are subject to change without notice.

Limited Warranty

5-YEARS FOR DRIVERS AND CABINETS,
3-YEARS FOR ELECTRONIC COMPONENTS

GoldenEar™ warrants to the original retail purchaser only that this GoldenEar Loudspeaker Product (the “Product”) will be free from defects in materials and workmanship for a period of five (5) years covering the drivers and cabinets, and three (3) years for the electronic components from the date of the original purchase from a GoldenEar Authorized Dealer. However, this warranty will automatically terminate prior to the expiration of five (5) years for the drivers and cabinets and three (3) years for the electronic components if the original retail purchaser sells or otherwise transfers the Product to any other party. The original retail purchaser shall hereinafter be referred to as “you.” Defective Products must be shipped, together with proof of date of purchase, prepaid insured to the Authorized Dealer from whom you purchased the Product, or to the nearest factory service center. Product(s) must be shipped in the original shipping container or its equivalent; in any case, the risk of loss or damage in transit is to be borne by you. If, upon examination at the Factory or a GoldenEar Authorized Dealer, it is determined that the unit was defective in materials or workmanship at any time during this Warranty period, GoldenEar or the GoldenEar Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below. All replaced parts and Product(s) become the property of GoldenEar. Product(s) replaced or repaired under this Warranty will be returned to you, within a reasonable time, freight collect.

This Warranty does not include service or parts to repair damage caused by accident, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, the voltage in excess of the rated maximum of the unit, the cosmetic appearance of cabinetry not directly attributable to defects in materials or workmanship, or service, or repair or modification of the Product which has not been authorized by GoldenEar. GoldenEar makes no Warranty with respect to its Products purchased from dealers or outlets other than GoldenEar Authorized Dealers. This Warranty is in lieu of all other expressed Warranties. If this Product is defective in material or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above. In no event will GoldenEar be liable to you for any incidental or consequential damages arising out of the use or inability to use the Product, even if GoldenEar or a GoldenEar Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation may not apply to you.

All implied warranties on the Product are limited to the duration of this expressed Warranty. Some states do not allow limitations on how long an implied Warranty lasts, so the above limitations may not apply to you. This Warranty gives you specific legal rights, and you also may have other rights which vary from state to state.

This product complies with the essential requirements of the EMC directive 89/336/EEC

Visit us at www.goldenear.com
Copyright © 2021 GoldenEar. All rights reserved.
Reproduction in whole or in part without our express permission is prohibited.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>