Inateck KB02028 Bluetooth Keyboard Instruction Manual

Inateck KB02028 Bluetooth Keyboard

Product Diagram

Power ON/OFF KB02028

1. Power ON: Toggle the switch to ON.
2. Power OFF: Toggle the switch to OFF.

Pair KB02028 with a Surface Go

• Step 1: For the first time you pair KB02028 with a Surface Go, you just need to toggle the switch on the KB02028 to the “ON” position and KB02028 will enter Bluetooth pairing mode automatically. To enter this mode, you can also hold simultaneously for 3 seconds and then the Bluetooth indicator will flash to indicate that KB02028 is under pairing mode.
• Step 2: On the Surface Go, select All Settings – Devices – Add Bluetooth or Other Device — Bluetooth, and then “Inateck KB02028” will show up as an available device.
• Step 3: Select “Inateck KB02028” on Surface Go.
• Step 4: When the blue indicator keeps on, it means that KB02028 is paired with the Surface Go successfully.

Note:
If KB02028 doesn’t work even though the blue indicator stays on, it might have been paired with another nearby computer. In this case, please follow the steps in “Troubleshooting in Bluetooth Pairing” to resolve the issue.

TroubIeshooting in Bluetooth Pairing

• Step 1: Delete all the Bluetooth pairing records related to KB02028 on the Surface Go.
• Step 2: Hold simultaneously for 3 seconds. The 3 indicators will flash 3 times simultaneously and then the blue indicator will flash, which means that the keyboard enters Bluetooth pairing mode. Under this mode, please re-pair the keyboard with the Surface Go.

LED Indicator

Keyboard Backlight

1. Hold simultaneously to adjust the backlight color. 7 colors are available in total.
2. Hold simultaneously to adjust the backlight brightness. 3 levels are at your choice.

Note:
When the battery level is lower than 20%, the backlight turns off automatically.

Function Keys

How to Use Fl-F12
You may press the keys to enable/disable the Fn lock. (The keyboard disables the lock by default.)

When the Fn lock is enabled:

• The press can trigger the functionality owned by .
• Press to dim the brightness of the screen;
• This method applies to all F Keys ( ).

When the Fn lock is disabled (Default Status):
Press the to dim the brightness of the screen. Press simultaneously to use the functionality owned by .

Fn+Key Combinations

Restore Factory Settings

If you are unsure what settings you have made on KB02028, you may hold simultaneously for 3 seconds to restore the factory setting.

Note:
After the factory reset, the keyboard would enter Bluetooth pairing mode automatically. You need to re-pair: KB02028 with your Surface Go.

Check Battery Level

Press simultaneously to check the battery level when KB02028 is not being charged.

Charging

When the battery level is under 20%, the red indicator will flash. Please recharge the KB02028 in time. The recommended charging voltage is 5V. To charge KB02028, you can connect the USB cable to the charger of a cellphone or the USB port of a computer. The keyboard will be fully charged after 3 hours.

Note: It is not recommended to charge KB02028 with a fast charger.

Product Specification

Packing List

• KB02028 *1
• Charging Cable *1
• Instruction Manual *1

FCC Note

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the Users, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Note:
The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirements. This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co- located or in conjunction with any other antenna or transmitter.

EU Declaration of Conformity

• Inateck Co., Ltd. hereby declares that this device complies with the Directive 2014/53/EU.
• A copy of the Declaration of Conformity can be accessed from https://www.inateck.de/pages/euro-compliance.

Service Center

Europe

F &M Technology GmbH

• Tel: +49 341 5199 8410 (Working day 8 AM – 4 PM CET)
• Fax: +49 3415199 8413
• Address: Fraunhoferstraße 7, 04178 Leipzig, Deutschland

North America

Inateck Technology Inc.

• Tel: +1 (909) 698 7018 (Working day 9 AM -5 PM PST)
• Address: 2078 Francis St., Unit 14-02, Ontario, CA 91761, USA

EC/REP

• F&M Technology GmbH Fraunhoferstraße 7, 04178 Leipzig, Deutschland
• Tel: +49 341 5199 8410

UK/REP

• Inateck Technology (UK) Ltd. 95 High Street, Office B, Great Missenden, United Kingdom, HP16 OAL
• Tel: +44 20 3239 9869

Manufacturer
Shenzhen Inateck Technology Co., Ltd.

Address:
Suite 2507, Block 11 in Tian An Cloud Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>