HUSKY N2W772478W4B 4-Tier Industrial Duty Steel Freestanding Garage Storage User Guide
- October 30, 2023
- Husky
Table of Contents
4-SHELF STORAGE RACK
RACK DE ALMACENAMIENTO DE 4 ESTANTES
77 in. W X 24 in. D X 78 in. H
1.95 m AN X 60.9 cm PR X 1.98 m AL
US Patents &
Patents pending
| ITEMS | MODELS |
|---|---|
| 1007784729 | N2W772478W4B |
| 1007587676 | N2W772478W4R |
N2W772478W4B 4-Tier Industrial Duty Steel Freestanding Garage Storage
USE AND CARE GUIDE
Questions, problems, missing parts?
Contact us directly for assistance:
7 a.m. – 5 p.m., CST, Monday-Friday
Chat: www.edsal.com
Email: support@edsal.com
**** Phone: 1-773-475-3131
To obtain replacement parts please provide: Model Number, Part Number &
Description, Store Location and Date Purchased.
THANK YOU FOR YOUR PURCHASE
Important Safety Information
WARNING
- Unit must be placed on a level surface or leveled with included hardware (when applicable).
- Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
- For safety reasons, it is imperative that this unit be mounted on the wall or floor.
- Unit can tip over causing severe injury or death.
- Do not exceed the recommended weight limits.
- Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
- Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury.
- Contains small parts, keep children away during installation.
- Use two or more people to assemble and move the unit to avoid injury.
- Use care when working with metal parts, wear gloves for protection.
- Do not use this unit to store aquariums.
- Maximum weight capacity per shelf is 2,500 lbs. (1133.9 kg) when weight is evenly distributed; or 10,000 lbs. (4535.9 kg) total unit capacity, evenly distributed.
- Do not use this unit for anything other than the manufacturer’s intended purpose.
- Mounting hardware not included. Consult with your local hardware dealer to find suitable hardware for securing to your floor or wall.
- Periodically inspect the unit to ensure beams are properly secured to the frame.
- Keep this manual for future reference.
Contents
PARTS LIST
| ITEMS: 1007784729
MODELS: N2W772478W4B| ITEMS: 1007587676
MODELS: N2W772478W4R
---|---|---
PART| PART NUMBER| PART NUMBER
A| N2W-FM2478-BLK| N2W-FM2478-RED
B| N2W-BM77-BLK| N2W-BM77-RED
C| N2W-TB24-BLK| N2W-TB24-BLK
D| 2472W-B-2S| 2472W-B-2S
Preparation
Before beginning assembly, read through the instructions and make sure all
parts are present. Make sure when assembling the beams (B) to frames (A) the
narrow end of the frame slots are facing down so the beam tabs can seat into
bottom of slot (see FIG.1). A rubber mallet may be used to tap on the beam to
insure the tabs are properly seated into the bottom of the slots. When
connecting the beams (B), make sure the obround hole of the ledge is facing on
the bottom to ensure correct assembly (see FIG.2). It is recommended to evenly
space out each shelf level assembly.
Helpful Tools/Items (not included):
• Rubber Mallet|
---|---
• Gloves|
Assembly
Assemble B (x8) to A (x2)
 Assemble C (x12) to beams
Assemble D
(x4) to beam assembly
NOTE: Wire decks (D) should be installed with the long horizontal wires facing the bottom.
Warranty
GUARANTEED FOREVER. If your Husky product ever fails bring it back and we will replace it for free. This full warranty gives you specific rights which vary from state to state. If this product is defective contact the manufacturer for repair or replacement parts.
Retain this manual for future reference.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>