Sportneer Bicycle Trainer Stand User Manual

June 14, 2024
Sportneer

Sportneer User Manual-Turbo
Trainer 01Sportneer Bicycle Trainer Stand

Sportneer Bicycle Trainer Stand
User Manual

Thank you for choosing Sportneer! Please read this manual carefully and keep it for future reference

Description

No more rainy day excuses take the velodrome into your living room with the Sportneer Indoor Bicycle Trainer Stand! You’ll be able to feel the burn from the comfort of your own home. With a wide base, S adjustable rubber feet, and a  low stance, this stationary bike converter offers unparalleled stability. You won’t shake and wobble no matter how hard you pedal! This bicycle stand reduces noise by spinning the back wheel only. Obnoxious whirring is eliminated, much  to the relief of vour spouse, pets, and kids! Training for the tail? The Sportneer Indoor Bicycle Trainer Stand includes 6 remote- controlled resistance settings to help you simulate even the toughest inclines. Going on a trip? At only 21,3  7.9″ 1 25.2″ when folded, this stand is small enough to stash in your trunk or in your suitcase.

Features

  1. Easy installation and operation
  2. 6 resistance settings
  3. Noise reduction
  4. Suitable for 26-28 inch bicycles and 700C bicycles

Specifications

Size. 22″ 22″ + 15.5/ 55.8×55.8839.4 cm
Folded Size: 21 3″ 7.925.2/ 542064 er
Maxmium Weight 250lbs/115kg (including the weight of the bike)
Net Weight: 16.5lbs/7.5kg
Gross Weight 18.7lbs/8.5kg

Instructions

Sportneer Bicycle Trainer Stand - Figuer 1

  1. Unfold the trainer and twist the knob to loosen.

  2. Pull out the resistor wheel.
    Sportneer Bicycle Trainer Stand - Figuer 3

  3. Detach the axle of your bicycle’s back wheel. Replace the axle with the quick release.
    Note: Do not use the quick release if your bike has a bolt axle. (fig. N)
    Sportneer Bicycle Trainer Stand - Figuer 5

  4. Line up the left side of the bicycle’s rear axle with the notches on the left side of the stand. Center your bicycle in the middle of the resistance wheel. Rotate the resistance wheel to fasten the roller. Press down the lever clamp on the  side of the stand to secure the bicycle.

  5. After fastening the back wheel of your bike, adjust the resistance wheel until it makes contact with the tire.
    The resistance wheel should be tight enough to provide resistance but loose enough to allow movement.

  6. Place the resistance controller on your handlebars and twist the knob to secure.

  7. Place the wheel pad underneath your front wheel. You’re ready to ride!
    Sportneer Bicycle Trainer Stand - Figuer 6

How to Adjust Your Trainer Stand

  1. Before riding, make sure your tires are properly inflated.
  2. Make sure the resistance wheel contacts with the tire.
  3. Twist the dial on the resistance controller to switch between settings. Setting 1 provides the least resistance and setting 6 provides the most.
    Sportneer Bicycle Trainer Stand - Figuer 7

Removing Your Bicycle

  1. Remove the resistance controller and the connecting cable.

  2. Pull up the lever clamp.
    Sportneer Bicycle Trainer Stand - Figuer 8

  3. Remove your bike from the trainer stand. Hold your bicycle by the frame to prevent it from falling down.
    Place the back wheel on the ground and remove the front wheel pad.

  4. Fold the stand and store it in the original packaging.
    Sportneer Bicycle Trainer Stand - Figuer 9

Notes: Be careful not to pinch your fingers when folding the stand.
Do not place anything on the stand. Excessive weight will cause damage.

Warnings

  • Do not use the bicycle trainer stand on the uneven ground.
  • Do not slam on the breaks when using the trainer stand. This places undue stress on the resistance wheel and on the bicycle tires,
  • Make sure your bicycle is securely fastened before use
  • Do not touch your tires while riding
  • Make sure your tires are properly inflated
  • Do not let go of the handlebars while riding
  • Warm up before exercising to prevent injury
  • Keep the trainer stand away from pets and young children

Troubleshooting

How can I reduce noise when riding?
Change to unstriped slicks to eliminate shaking
Place the stand on a blanket or mat
Why doesn’t the resistance change when I turn the dial?
The resistance wheel may be too loose. Tighten the nut in the resistance wheel to increase tension
Resistance increases gradually, Wait for a few seconds for the resistance wheel to tighten.

Package Contents

1 x Magnetic Resistance Biker Trainer Stand
1 x Replacement Skewer
1 x Front Wheel Block

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals