DIGITUS DN-95320-1 Fast Ethernet PoE Switch Installation Guide
- June 5, 2024
- DIGITUS
Table of Contents
DIGITUS DN-95320-1 Fast Ethernet PoE Switch
Copyright Statement
Our company reserves all copyrights of this document. Any reproduction,
excerption, backup, modification, transmission, translation or commercial use
of this document or any portion of this document, in any form or by any means,
without the prior written consent of our company is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject
to change without any notice. Please obtain the latest information through our
company website. Our company endeavors to ensure content accuracy and will not
shoulder any responsibility for losses and damages caused due to content
omissions, inaccuracies or errors.
Product Introduction
The DIGITUS DN-95320-1 is a 5-Port 10/100M Desktop PoE Switch, that enables a
seamless network connection. It integrates 100 Mbps Fast Ethernet and 10 Mbps
Ethernet network capabilities. These PoE ports can automatically detect IEEE
802.3af/at-compliant Powered Devices (PDs) and supply them with power. The
operating mode can be changed using the slide switch on the front side.
When switching into extend mode, Ports 2-5 can be switched into long range
mode at up to 250 meters with 10 Mbps. The DN-95320-1 is easy to install and
to use. It does not require any configuration or installation. With its
desktop design, outstanding performance and quality, the 5-Port 10/100 Desktop
PoE Switch is an excellent choice for extending video monitoring or WLAN
access points.
Features
- PoE support: Port 1-4 (802.3 af/at)
- PoE total output: 60 watts
- 4 RJ45 PoE Ports
- An RJ45 port can also be used as an uplink port
- External power supply, sophisticated design, suitable for desktop installation
- LED displays: PoE, link, activity
- Supports data transfer of up to 250 m at a rate of 10 Mbps.
- Automatically detects PoE devices on connection, devices that are not PoE-capable can also be used.
Package Contents
Before installing the Switch, make sure that the following the “packing list” listed OK. If any part is lost and damaged, please contact your local agent immediately. In addition, make sure that you have the tools install switches and cables by your hands.
- 1 x 5-Port 10/100Mbps Ethernet Unmanaged PoE Switch (4-Port PoE).
- 1 x Installation Component
- 1 x DC Power Adapter
- 1 x Quick Installation Guide
Hardware Specifications
Standards| IEEE802.3i, IEEE802.3u, IEEE802.3x, IEEE802.3az,
IEEE802.3at, IEEE802.3af
---|---
Interface| 5 x 10/100Mbps
Auto-Negotiation ports
Mode switch-|
- Default mode:1-5 port speed rate 100 Mbps, communicate with each other
- Extend mode:1port speed rate 100Mbps,2-5 PoE port rate of 10 Mbps, the farthest distance is 250m, communicate with each other
Network Media| 10Base-T: UTP 5e and above cable (maximum 250m)
100Base-Tx: UTP category 5, 5e cable (maximum 100m)
Transfer Method| Store-and-Forward
MAC Address Table| 1K
Switching Capacity| 1Gbps
Packet Forwarding Rate| 0.744 Mpps
PoE Ports(RJ45)| 4x PoE ports compliant with 802.3at/aft
Power Pin Assignment| 4/5(+), 7/8(-)
PoE Budget| 60W
LED indicators|
Per Port
| Link/Act: Green PoE: Orange
Per Device
| Power: Green
Power Supply| DC 53.5V,1.2A External Power
Power Consumption| Maximum (PoE on): 66.5W (220V/50Hz)
Dimensions (W x D x H)| 89.381.721.3mm
---|---
Environment|
- Operating Temperature: 0℃ – 45℃
- Storage Temperature: -40℃ – 70℃
- Operating Humidity: 10%~90% RH non-condensing
- Storage humidity: 5%~90% RH non-condensing
External Component Description
-
Front Panel
The front panel of the Switch consists of one power LED indicator, five Link/Act LED indicators, four PoE LED indicators and one slide switch
-
Default/Extend mode switch:
It can through the front panel of the slide switch to switch working mode. When switch to Extend mode, 2-5 port rate negotiation into 10 Mbps, Data transmission and power supply can reach as far as 250 meters.
You can with LED indicator quickly judge the Switch work, help diagnose problems in the Switch or the connected devices. LED indicator as shown below: -
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential problem with the Switch, connection or attached devices.
-
The
following chart shows the LED indicators of the Switch along with explanation
of each indicator.
LED Indicator
|
Faceplate Marker
|
Status
|
Indication
---|---|---|---
Power Indicator| PWR| Off| Power Off
Solid green| Power On
10/100 BASE-T adaptive Ethernet port indicators (1-5)| Link/Act| Off| The port
is NOT connected.
Solid green| The port is connected, but no data is transmitting or receiving.
Blinking| The port is transmitting or receiving data.
PoE status indicators (2-5)| PoE| Off| No PD is connected to the corresponding
port, or there is a breakdown.
---|---|---|---
Solid orange| A Powered Device is connected to the port, which supply power
successfully.
Blinking| The PoE power current may be overloaded
-
Rear Panel
The rear panel of the Switch consists of 5 x 10/100Mbps RJ-45 ports and a power connector.
-
10/100Mbps RJ-45 ports (1~5):
Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each has a corresponding 10/100Mbps LED, port2~port5 support PoE power supply function, each has a corresponding PoE LED. -
UP-link port:
Up-link port as an automatic flip cascade port, can be used with the other 4 RJ-45 ports, the port corresponds to the Link/Act indicator. -
Power Connector:
Power is supplied through an external DC power adapter. It supports 53.5V DC.
-
Installing and Connecting the Switch
This part describes how to install your PoE Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented.
Installation
Please follow the following instructions in avoid of incorrect installation causing device damage and security threat.
- Put the Switch on stable place or desktop in case of falling damage.
- Make sure the Switch works in the proper DC input and matches the voltage labeled on the Switch.
- To keep the Switch free from lightning, do not open the Switch’s shell even in power failure.
- Make sure that there is proper heat dissipation from and adequate ventilation around the Switch.
- Make sure the cabinet to enough back up the weight of the Switch and its accessories.
Desktop Installation
When installing the Switch on a desktop, please attach these cushioning rubber
feet provided on the bottom at each corner of the Switch in case of the
external vibration. Allow adequate space for ventilation between the device
and the objects around it.
Power on the Switch
The Switch connected an external power adapter power 53.5V/1.2A supply, make sure you use the proper power supply.
Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be connected to any RJ-45 port of the Switch, the distance between Switch and computer is around 100 meters. Once the connection is OK and the devices are power on normally, the LINK/ACT status indicator lights corresponding ports of the Switch.
Switch connection to the PD
2~5 port of the Switch have PoE power supply function, the maximum output
power of single port up to 30W, it can make PD devices, such as internet
phone, network camera, wireless access point work. You only need to connect
the Switch PoE port directly connected to the PD port by network cable.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is
part of the shipping content. If the Declaration of Conformity is missing, you
can request it by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>