Hyundai HC 103 Hair and beard trimmer Instruction Manual

: June 5, 2024
: HYUNDAI

Table of Contents

Hyundai HC 103 Hair and beard trimmer
GENERAL SAFETY INSTRUCTIONS
DESCRIPTION OF THE CONTROLS
USING THE CUTTING GUIDES
CUTTING TECHNIQUES AND ADVICE FROM THE EXPERTS
MAINTENANCE
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Hyundai HC 103 Hair and beard trimmer

Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the warranty, the receipt and, if possible, the box with the internal packing.

GENERAL SAFETY INSTRUCTIONS

Check whether the data on the type label corresponds with the voltage in your socket.
This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!
Do not leave the iron plugged in the power supply without supervision!
If the power cord of the charger is corrupted, it has to be replaced by the manufacturer, its service technician, or a similarly qualified person so as to prevent dangerous situations.
Never use the appliance if its power cord or plug is damaged, if it does not work properly if it fell down and was damaged and it is leaking. In this case, take the appliance to a special service to check its safety and proper function.
Never use the appliance if it does not work properly, if it fell down and was damaged or if it fell to the water.
The appliance is intended for use in households only and for similar use! It is not designed for use in hair salons or for other commercial use!
Do not put or take out the plug to or from a socket with wet hands!
Do not let the appliance in operation without supervision!
Never immerse the appliance in water or other liquids (even partially) and do not clean it in running water!
Use only the accessories designed for this type. Do not use damaged adapters.
Never tuck the appliance or the accessories into anybody’s holes.
Be careful in using the appliance without a set adapter, the blades are sharp.
Do not use the appliance while having a bath, having a shower or taking a sauna and for trim-ming wet or artificial hair.
The appliance is not intended for styling animal hairs.
Never charge the appliance in direct sunlight or close to heat sources and if the temperature is below 10 °C or above 40 °C. If the appliance is fully loaded (all the control lights are permanently on), unplug the charging device.
Do not put the trimmer on hot heat sources (e. g. oven, stove, radiator, etc.)
The trimmer and the stand with the plugged adapter must not be used at places where it could fall into a bathtub, a wash basin or a swimming pool. If the dryer fell to water anyway, do not take it out! First of all, unplug the adapter from the socket and only then remove the trimmer. In this case, take the appliance to a special service to check its safety and proper function.
If the dryer was stored at lower temperatures, acclimatize it first, by which you remove the stiff-ness of the lubricating fat in bearings and mechanical resistance of the plastic parts will be maintained.
Also, do not put the trimmer in the on position on soft surfaces (e. g. bed, towels, sheets, carpet); the surfaces or the appliance could get damaged.
The power cord of the adapter must not be damaged by sharp or hot objects, or open fire and it must not be sunk into the water.
If you need to use the extension cord, it has to be uncorrupted and it has to comply with the valid standards.
The adaptor supplied with this appliance is intended for this appliance only, do not use it for other purposes. Also, use only the supplied adaptor with this appliance, do not use any other adaptor for charging (e.g. from another appliance).
During normal operation, the accumulator batteries are not taken out. Take out the batteries only if the appliance is to be disposed of.
Never use the appliance for any other purpose than for the intended purpose described in these instructions for use!
The producer is not responsible for any loss caused by improper handling of the appliance and its accessories (e. g. injury, appliance damage, fire, etc.) and its guarantee for the appliance does not apply in the case of non-compliance with the safety instructions above.
Oil: Warning, Avoid contact with eyes, Do not drink, and Keep away from children.
Do not use the appliance close to bathtubs, showers, bash basins or other water containers.

DESCRIPTION OF THE CONTROLS

2 cutting guides for 22 lengths(from 3-18mm and from 21 to 36mm, in 1.5mm steps)
1 precision guide (0.5-2.5mm)
blades:
moving blade: sharpened process: for an exceptional cutting edge.
long-lasting: ultra hard-wearing and 100% stainless steel blade.
Faxed blade:
For longer life: Combining these technologies perfects the condition of the blade surface, thereby reducing their friction coefficient.
thinning system
thinning system button
adjust length wheel
ON/OFF button
charging indicator light
charging stand
cleaning brush
charging transformer
comb
Lock system

Hyundai-HC-103-Hair-and-beard-trimmer-fig-1

CHARGING THE CLIPPER
Before using the clippers for the first time, charge for 16 hours. The charging cord can be put in the stand (Fig. 1)

Plug the transformer into the mains.
Place the clipper in the stand. Always check that the indicator light is on when the clipper is in the stand.
When fully charged, you will be able to use the clipper for up to 45 min. The charging cord also can be put into the mains for charging.(Fig. 2)

USING THE CUTTING GUIDES

IMPORTANT: Always attach the cutting guide BEFORE turning the clipper on and turn the clipper off to change guides. The cutting guide is very practical and guarantees an even cut. To attach a cutting guide, first, adjust the cutting length to 3 mm or 21 mm and place it on the support guide adjusting first on both sides and pushing on the bottom of the guide until you hear a “click”. (Fig. 3) NOTE: The precision guide must be placed like the cutting guides but it is adjusted manually and independently of the grooved wheel.
STARTING AND USING
To adjust the clipper’s cutting length, turn the grooved wheel up or down. The selected length is displayed on the right or left side of the clipper. Press the ON/OFF button. You can change the cutting length at any time. Thanks to the smart adjusting system,the length of the cut is maintained even if the angle of the clipper varied, so it guarantees a precise results.
TO TURN THE CLIPPER OFF
Either: press the ON/OFF button ,the unit will shut down completely and adjust the wheel to make sure the cutting guide return to its original position .
To remove the cutting guide, first adjust the cutting length to 3mm or 21mm and push the guide out of the support lifting it up with your thumb. (Fig. 4)

CUTTING TECHNIQUES AND ADVICE FROM THE EXPERTS

Use the clipper on clean, dry hair.
To familiarize yourself with the clipper, begin with the cutting guide for a longer cut, and adjust it by sliding the wheel. You will soon know the lengths of each guide and each position.
Always move the clipper against the direction of hair growth.
Begin at the nape. Place the guide on the scalp and move the clipper toward the crown of your head. Move your clipper slowly, pointing the teeth of the guide slightly upward. Keep the clipper in contact with your head at all times (Fig. 5)
For the crown of the head, move from the front to back, that is, from your forehead to the crown of your head.
For the finishing touches, that is, around the nape and sideburns, use the clipper without a cutting guide. Turn your clipper over and move it from top to bottom. (Fig. 6)
If you want a length greater than 30 mm, or if you are experienced, you can create “comb” or “finger” cuts:
- Work without a cutting guide.
- Take up a small section of hair with a comb or in your fingers.
- Move the comb or your fingers along the section of hair to the desired length.
- Cut your hair along the coomb or your fingers.
- Remove the cut hair using a comb and check the evenness of the cut regularly.(Fig.7)

USING THE THINNING GUIDE
Switch the clipper to the “THIN” position. The thinning guide is in front of the blades. This technique allows you to thin out hair to make styling easier. The technique is particularly good for the crown of the head where hair is usually thicker. To thin your hair, take a section of hair (rest your little and ring fingers on your scalp, using the middle and index fingers to set the length), hold 1 to 2 cm below the cutting length. Then, using the clipper, cut the section of hair steeply and at an angle to create a sawtoothed “edge”.

MAINTENANCE

Remove the cutting guide after each use.
Cleaning the clipper blades regularly will maintain their optimal performance.
Removable blades
To make cleaning easier, the clipper blades can be removed. Make sure the clipper is turned off. Hold the clipper with the blades pointing up and remove them by pressing the top of the blade.(Fig. 8)
Brush the blades using the cleaning brush to remove any hair.
It is nevertheless recommended that you put oil on the blade when you notice the clipper isn’t performing as well.
Remove the blades as described above.
Carefully squeeze a few drops of oil onto the pad.
Then put the blades back on the clipper.
Oil is specially formulated for clippers, it will not evaporate or slow the blades down.
You can get new blades when these are worn or damaged.

NI-MH BATTERIES
This clipper has nickel-metal hydride batteries. In an effort to protect the environment, these batteries should be removed and properly disposed of when the unit is no longer operating.To remove the battery block for disposal or recovery,follow these instructions:

First, unplug the clipper. Remove the 3 screws on the back, 2 at the top and 1 at the bottom.
Open the clipper and remove the batteries using wire cutters.
To protect the environment, do not dispose of your batteries with your ordinary household waste. For more details on the recovery of materials and waste treatment facilities, please contact the waste disposal services in your region.

TECHNICAL SPECIFICATIONS

Hair trimmer
Rechargeable hair and beard trimmer with charge stand
2 cutting attachments for hair length settings (3 – 36 mm)
1 cutting attachments for beard length settings (0,5 – 2,5 mm)
Battery operation – NiMH battery
Operating time up to 45 minutes
Charging time 8 hours
Accessories: charging adaptor, charging stand, cleaning brush, oil, comb
Power drain: 1,5 W
Noise level: < 64 dB
Power supply: 230 V ~ 50 Hz
Size: 5,5 x 16,5 x 4,3 cm
Weight: 0,2 kg

We reserve the right to change technical specifications.

WARNING: Do not use this product near water, in wet areas to avoid fire or injury of electric current. Always turn off the product when you don’t use it or before a revision. There aren’t any parts in this appliance that are reparable by consumers. Always appeal to a qualified authorized service. The product is under dangerous tension.

Old electrical appliances used batteries, and accumulators disposal

This symbol appears on the product, on the product accessories or on the product packing means that the product must not be disposed of as household waste. When the product/ battery durability is over, please, deliver the product or battery (if it is enclosed) to the respective collection point, where the electrical appliances or batteries will be recycled. The places, where the used electrical appliances are collected, exist in the European Union and in other European countries as well. By proper disposal of the product, you can prevent possible negative impacts on the environment and human health, which might otherwise occur as a consequence of improper manipulation with the product or battery/ accumulator. Recycling of materials contributes to the protection of natural resources. Therefore, please, do not throw the old electrical appliances and batteries/ accumulators in the household waste. Information, about where it is possible to leave the old electrical appliances for free, is provided at your local authority, at the store where you have bought the product. Information, where you can leave the batteries and accumulators for free, is provided to you at the store, at your local authority.