concept CP 2000 Steam Cleaner Instruction Manual

concept CP 2000 Steam Cleaner

ACKNOWLEDGMENT

Thank you for purchasing a Concept product. We hope you will be satisfied with our product throughout its service life.
Please study the entire Operating Manual carefully before you start using the product. Keep the manual in a safe place for future reference. Make sure that any persons handling the vacuum cleaner are also familiar with this Operating Manual.

Technical parameters

Voltage| 220-240 V ~ 50/60 Hz
Input power| 1500 W

IMPORTANT SAFETY INSTRUCTIONS

Do not leave the appliance unattended when plugged into the mains. When using an electric appliance, the following precautions should always be followed:

• Do not leave the appliance unattended when plugged into the mains. Always disconnect the device from the mains before maintenance or if it is not in use.
• Do not use outdoors or on wet surfaces.
• Do not put the device in operation when in the upright or locked position.
• Do not let the device run while it is stationary. Keep the device moving when it is in use.
• Do not allow the device to be used as a toy. Close attention is necessary when the device is used near children.
• Use the device only as described in this manual. Always use only manufacturer’s recommended attachments.
• Always unplug the device from the mains when filling with water, emptying it or if the appliance is not in use.
• Do not use the device if the cord or plug is damaged. If the device does not work as it should, it may have been dropped, damaged, left outdoors, or immersed in water, contact an authorized service centre.
• Do not pull on the power cord, do not carry the device by holding the power cord, do not use the cable as a handle, do not close the cable in the door, or rotate it around sharp edges or corners.
• Keep the cord away from heat sources.
• Do not run the device over the cord.
• To unplug the appliance, grasp the power plug and pull it out. Do not pull the power cord.
• Do not touch the plug or the device with wet hands.
• Do not use the device without the water tank cap in place.
• Do not use the steam function with an empty water tank.
• Empty the water tank when the steam cleaner is not in use.
• Do not put any object into the device’s openings. Do not use the device with any opening blocked; keep it free of dust, lint, hair and anything that may reduce performance.
• Contact the manufacturer/retailer (see warranty and service terms). Incorrect installation and repair can cause electrical shock to the user.
• Keep your hair, clothing, fingers and all parts of body away from openings and moving parts of the device.
• Do not ever aim the steam cleaner on yourself or another person. Steam is very hot and can cause burns. Do not use the appliance in the presence of explosive or flammable vapours.
• Turn off all controls before unplugging.
• Do not use the device to clean hot or smoking objects, such as cigarettes, matches, or hot ash.
• Use extra care when cleaning the stairs.
• Do not use the device to clean up flammable or combustible liquids, such as gasoline or lighter fluid. Do not use the device areas where such liquids may be present.
• Do not use to pick up flammable or combustible liquids, such as gasoline or lighter fluid, or use in areas where they may be present.
• Do not use the device in an enclosed space where flammable, explosive or toxic vapours may be released from oil base paint, diluent, moth preparations, or in areas where flammable dust is present.
• Use of chemicals may damage the appliance and you will lose your warranty.
• Do not use the device to clean up toxic solutions such as chlorine bleach, drain cleaner, gasoline, etc.
• Never put additives (such as perfume, stain remover or products containing alcohol) in water as they may damage the steam cleaner or make it dangerous to you.
• Ensure that the water tank cap has been properly screwed down before use.
• Do not touch hot parts of the device. It is normal for the device to get hot during operation.
• Do not use the device to clean clothes while being worn.
• The impact of the steam may have an adverse effect on some materials. Always test the steamer on a small area to determine if the particular material is suitable for treatment with the steam cleaner.
• Never aim the device at people, animals or plants (risk of scalding!).
• Do not aim the appliance at electrical systems or wires.
• Do not repair the appliance yourself. Contact an authorized service centre.
• This appliance may be used by children 8 years of age and older and by persons with physical or mental impairments or by inexperienced persons if they are properly supervised or have been informed about how to use of the product in a safe manner and understand the potential dangers. Children must not play with the appliance. This appliance may be cleaned by children 8 years of age and older if they are properly supervised. Keep this appliance and the power cord out of reach of children younger than 8 years of age.

If you fail to follow the manufacturer’s instructions, repairs cannot be recognized as a warranty.

Household use only
The steam vacuum cleaner with a mop is designed for use on hard surfaces such as ceramic, glass, stone, marble, concrete, vinyl, linoleum and sealed hardwoods and carpet. The appliance is not designed for use on fine silks, leather, velour, or other delicate steam-sensitive materials such as waxed polished furniture, very thin plastics, unsealed hardwoods, ceilings, drywall and exterior paint of automobiles, electronics or items using electricity.
NOTE: The heat and steam may not be suitable for some steam or heat- sensitive floor types. If unsure, we recommend checking the use and care instructions from the floor manufacturer and testing on an inconspicuous area prior to use.

PRODUCT DESCRIPTION

1. Steam trigger
2. Handle
3. Power cord
4. Power On/Off button
5. Manual cleaner handle
6. Manual cleaner steam trigger
7. Cleaning solution foot pedal
8. Cleaning solution tank cap
9. Cleaning solution tank
10. Hook for attaching a power cord
11. Manual cleaner release button L Water tank release button
12. Water tank
13. Head
14. Brush
15. Hose adapter
16. Hose
17. Extension adapter
18. Textile pad
19. Carpet glider
20. Small textile pad
21. Window squeegee / Head for upholstery (with a small textile pad)
22. Wire brush
23. Nozzle (45°)
24. Small round brush
25. Large round brush
26. Scraper
27. Tile joint brush 

OPERATING INSTRUCTIONS

Assembly
Remove all components from the packaging.

1. lnsert the handle into the cleaner main body until it locks into position (1).
2. Assemble the main body of the cleaner to the Floor Head (2). 

Use

BEFORE THE FIRST USE

1. Press the Water Tank Release Button and remove the tank (3). NOTE: A tube feeding water from the water tank to the boiler is loaded with a brass ball. This design is intentional and serves to increase the efficiency of water use. It is normal for this ball to create a rattling sound inside the Water Tank during operation.

2. Pull the Water Tank by the cap (4).

3. Fill the tank with cold tap water. Secure the tank with the cap (4). Do not add any chemicals, detergents or perfumes to the Water Tank.
   NOTE: We recommend using distilled or de-mineralized water in order to reduce building up mineral deposits and prolonging the life of the appliance.

4. Put the Water Tank back in its place and make sure the Water Filter is installed.

5. Attach the Textile Pad on the bottom of the Head (5). 

IMPORTANT: Always disconnect the appliance from the mains prior to adding water or changing the Textile Pad.
NOTE: Wash the Textile Pad before putting on the appliance, it prevents a presence of any loose fibres.

FLOOR CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to the Head.
NOTE: Do not use the Carpet Glider for cleaning hard floor types.

1. Connect the steam cleaner into the mains. Press the power on/off button, the indicator will light blue.
2. After a few seconds half of the indicator will tum red, meaning the appliance is ready for use.
3. Put your foot on the head and angle the body of the cleaner downwards (6).
4. Press the trigger to release the vapour (7).
5. Move the cleaner slowly backwards and forwards paying particular attention to frequently used areas.

CARPET CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to the Head.

1. Attach the Carpet Glider to the Head (10).
2. Connect the steam cleaner into the mains. Press the power on/off button, the indicator will light blue.
3. After a few seconds half of the indicator will tum red, meaning the appliance is ready for use.
4. Put your foot on the head and angle the body of the cleaner downwards (6).
5. Press the trigger to release the vapour (7).
6. Move the cleaner slowly backwards and forwards paying particular attention to frequently used areas.

MANUAL CLEANER OPERATION

1. Press the Manual Cleaner Release Button and remove the steel tube (11).

2. Remove the Head (12).

3. Press the Water Tank Release Button and remove the Water Tank (3).
   NOTE: A tube feeding water from the water tank to the boiler is loaded with a brass ball. This design is intentional and serves to increase the efficiency of water use. It is normal for this ball to create a rattling sound inside the Water Tank during operation.

4. Pull the Water Tank by the cap and open it (4).

5. Fill the tank with cold tap water. Secure the tank with the cap (4). Do not add any chemicals, detergents or perfumes to the Water Tank.
   NOTE: We recommend to use distilled or de-mineralized water in order to reduce building up mineral deposits and prolonging the life of the appliance.

6. Put the Water Tank back on the main part of the cleaner and make sure the Water Filter is installed.

7. Connect the steam cleaner into the mains. Press the power on/off button, the indicator will light blue.

8. After a few seconds half of the indicator will tum red, meaning the appliance is ready for use.

9. Press the trigger to release the vapour (on the manual cleaner) (13). 

IMPORTANT: Always disconnect the cleaner from the mains prior to removing the Head or handling the appliance. Always ensure the cleaner has fully cooled down before removing the Head.

SOLUTION TANK USE

1. Rotate the Solution Tank cap counter-clockwise to open and fill the tank with a solution fluid (8).
2. Put back the Solution Tank cap and screw it clockwise.
3. Press the foot pedal to the ON position to engage the Solution Tank. Press the foot pedal to the OFF position to disengage.

IMPORTANT: To prevent solution from leaking ensure the foot pedal is in the OFF position when the product is not in use.

Empty the solution tank

1. Connect the steam cleaner into the mains. Press the power on/off button, t
2. he indicator will light blue.
3. Remove the Solution Tank (17).
4. Rotate the Solution Tank cap counter-clockwise to open.
5. Pour out the solution from the tank (17). Put back the Solution Tank cap, screw it clockwise, then put the tank back in its place.

Accessories

Without a hose

1. When the Head is removed, different accessories can be attached directly to the steam outlet of the appliance (14). Screw the accessories in clockwise until it is locked in position.

With a hose

1. Fit the Hose Adapter to steam outlet of the appliance (15).
2. Fit the Hose to the Hose Adapter. Align the orientation marks with the hole on Hose Adapter and rotate clockwise until hose is locked in position (15).
3. Slide the Release Button on the bottom side of the hose away from the appliance, rotate the hose counter-clockwise and gently pull out of the appliance.
4. Fit the Extension Adapter to the hose nozzle and rotate it clockwise until it locks in its place securely.
5. Fit other small accessories to the Extension Adapter, then rotate clockwise until it is locked in position (15).

Extension Adapter – Use it on heavily soiled areas such as showers, kitchens.
Window Squeegee – Use it on windows and mirrors for a smear free cleaning.
Upholstery Pad- Put the Upholstery Pad on the Window Squeegee and use it for sofa and chair upholstery cleaning.
Round Brush – Use it for stubborn grease and dirt deposits.
Wire Brush – Use it on oven grills and racks.
Angled Nozzle (45°) – Use it on hard to reach areas such as taps etc.
Scrapper – ldeal for dried residue in ovens or for defrosting freezers.

CLEANING AND MAINTENANCE

IMPORTANT: ALWAYS ENSURE THE CLEANER HAS FULLY COOLED DOWN BEFORE PERFORMING ANY MAINTENANCE TASKS.

Empty the Water Tank

1. Disconnect the cleaner from the mains and ensure the appliance has cooled down.
2. Release the Water Tank from the main body of the cleaner (3).
3. Remove the Water Tank cap.
4. Pour out any excess water from the tank (16). Put the cap back and secure it.

Changing and washing the Textile Pad

1. Disconnect the cleaner from the mains and ensure the appliance has cooled down.
2. Remove the Carpet Glider first if necessary and then remove the Textile Pad from the Head (18).
3. Wash the Textile Pad in a washing machine with a mild detergent at maximum temperature of 40 °C.
4. IMPORTANT: Do not use bleach or fabric softener when washing the Textile Pad.

Changing the Water Filter
The cleaner is fitted with a water filter. lf you live in an area with hard water the filter will discolour over time. Depending on the water hardness and frequency of use the filter should be changed every 6 months.

1. Disconnect the cleaner from the mains and ensure the appliance has cooled down.
2. Release the Water Tank from the main body of the cleaner (3).
3. Remove the Water Filter from the appliance (19). Replace the old filter with a new one.
4. Put the Water Tank back.

NOTE: The state of the filter will affect the cleaner performance.

TROUBLESHOOTING

If a problem occurs, look at this chart first. If that does not help, contact a service centre.
The steam trigger does not work.

• Check the appliance is connected to the mains.
• Check the power cord.

No vapour comes out of the steam nozzle.

• Maybe there is no water in the water tank.
• Maybe the water tank is not properly installed in the appliance.

The textile pad does not clean.

• The pad may be too saturated with dirt and needs to be washed. See the Maintenance section.

FAQ

How long does it take the device to be ready?
Approximately 25 seconds.
Can I use the device on all floor surfaces?
It can be used on all hard floor types such as marble, ceramic, stone, linoleum, sealed hardwood floors and parquet.
Does the device generate the steam automatically?
No, to generate steam you should press the steam trigger under the handle.
Can I put detergents or other chemicals inside the water tank?
No, it may damage the device.
What should I do if I live in an area where water is very hard?
You can use filtered water or you will have to change the filter more often. If a weak steam flow comes out from the nozzle, check the opening of the steam nozzle whether it is clogged with a scale.
When is it time to change the water filter? How do I notice?
It depends on the water hardness. Normally every 6 months. You may notice that the yellow colour inside of the filter has faded a bit.
How long will full water tank last before needing to be refilled?
Approximately 12 minutes if the trigger id pressed continuously.
Is the mop washable?
Yes, it can be washed by hand or in a washing machine with a mild detergent at max temperature of 40 °C. Do not use bleach or fabric softener.
How often should I replace the mop?
lt depends on different factors above all how hard the floor is. The best way to identify when to change the mop with a new one is when the mop is still dirty after having been washed or if you notice that it doesn’t perform like it used to.

SERVICE

Maintenance of a more extensive nature or repair, which requires interference with the internal parts of the product, must be performed by a professional service.

ENVIRONMENTAL PROTECTION

• Recycle packaging materials and old appliances rather than throwing them away.
• The appliance box may be disposed of at a sorted waste collection point.
• Deliver polyethylene (PE) plastic bags to a waste collection facility for recycling.

Recycling the product at the end of its service life
A symbol on the product or its packaging indicates that this product should not be disposed of as household waste. It must be taken to a collection point authorised for recycling electric and electronic equipment. By making sure this product is disposed of properly, you will help prevent negative effects on the environment and human health that would otherwise result from inappropriate disposal of this product. You can learn more about recycling this product from your local authorities, a household waste disposal service, or in the store where you purchased this product.
This product meets all the basic EU regulation requirements that relate to it. Changes to the text, design and technical specifications may occur without prior notice and we reserve the right to make these changes.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>