dBTechnologies IS210L Loudspeaker User Manual
- June 17, 2024
- dBTechnologies
Table of Contents
IS210L
420120422Q REV1.0
QUICK START USER MANUAL SECTION 1
MAIN FEATURES
- Impressive sound pressure
- Quick installation
- Multiple array configurations
PACKAGE CONTENTS
The box contains:
N°1 IS210L loudspeaker
N°2 front link brackets
N°2 back link brackets
This quick start and warranty documentation
DESCRIPTION
IS210L is the new dB Technologies 2-way passive line array speaker for
professional use. It is equipped with one compression driver (voice coil:
2,4”, exit: 1.4”) and two 10” neodymium woofers (2.5” voice coil). The
coverage pattern is 90° (H) x 15° (V).
The mechanical design allows an easy, accurate and quick installation for
flyable or stand use in array configuration thanks to the included brackets.
DIMENSIONS
TECHNICAL SPECIFICATIONS
Speaker Type | 2 Way Passive Loudspeaker |
---|---|
Protection against solid objects and liquids (IP): | 55 |
Frequency Response [-6dB] | 65 Hz – 17.5 kHz |
Usable Bandwith [-10dB] | 57 Hz – 18.7 kHz |
RMS power | 400 W |
Rated impedance | 8 Ohm |
Max SPL (1 m) | 133 dB (Fullrange) |
Directivity (HxV) | 90° x 15° |
HF | 1.4″ exit, 2.4″ v.c. |
LF | 2x 10″, 2.5″ v.c. |
Crossover Frequency | 900 Hz |
Signal Input | Terminal barrier strip (or speakON® using the SP-IS accessory |
panel)
Signal Output| Terminal barrier strip (or speakON® using the SP-IS accessory
panel)
Housing| Wooden box – black finished
Rigging Points| Integrated mechanics
Dimensions (WxHxD)| 675x310x400 mm
(26.6)(12.2)(17.8 in)
Weight| 29.2 Kg (64.4 lbs.)
ACCESSORIES
CONNECTIONS
PROTECTION AGAINST SOLID OBJECTS AND LIQUIDS (IP RATING)
The speakers are protected against the ingress of solid objects and liquids
with a rating of IP55 as defined by IEC 60529. Please only use cables with the
specified diameters:
PG7 => 6 or 6.5mm diameter
PG9 => 7.5 or 8mm diameter
Fasten properly the cable gland using the plastic tightening nut.
WARNING!
Failure to comply with these installation prescriptions could adversely affect
the declared protection ratings.
MECHANICAL FIXING POINT
Is 210L can be installed in array configuration, on each side of the
loudspeaker the user can find mechanical fixing points to fasten the
loudspeaker to another one or a to DRK flybar using the included brackets. The
(A) fixing points allow front link brackets mount; the (B) fixing points allow
back link brackets mount. The (C) fixing points allow to fasten another
speaker in array configuration.
FRONT LINK BRACKETS
The front link brackets allows to link the IS 210L to another loudspeaker or
to a DRK flybar. Fasten the brackets to the IS 210L (A) fixing points using
the SPK holes (in case of another loudspeaker mount) or the DRK holes (in case
of DRK flybar mount).
BACK LINK BRACKETS
The back link brackets allows to link the IS 210L to another loudspeaker or to
a DRK flybar and adjust the tilt angle from 1° to 15°.
Fasten the brackets to the IS 210L (B) fixing point using the SPK hole (in
case of another loudspeaker mount) or the DRK hole (in case of DRK flybar
mount).
INSTALLATION
On each side fasten the front and back link brackets to the loudspeaker depending on loudspeaker or DRK flybar coupling.
SPEAKER ARRAY MOUNT
Fasten the speakers using the holes as shown; select the tilt angle from the
back link brackets holes depending on the array configuration.
DRK-1 FLYBAR MOUNT
Fasten the speaker to the flybar using the holes as shown; an arrow on the
flybar indicate the hole to choose for the back link bracket fastening. Select
the tilt angle from the back link brackets holes depending on the array
configuration.
DRK-2 FLYBAR MOUNT
Fasten the speaker to the flybar using the holes as shown: A for positive
angle, B for negative angle. An arrow on the flybar indicate the hole to
choose for the back link bracket fastening. Select the tilt angle from the
back link brackets holes depending on the array configuration.
LP-6 BRACKETS FLOWN MOUNT
The LP-6 brackets allows to link IS 210L loudspeakers with IS 115S subwoofers
in flown or stack configurations. For the flown installation with LP-6
brackets follow this procedure:
- First remove the IS 210L side panels and internal link brackets
- Fasten the LP-6 brackets to the subwoofer
- Fasten the loudspeaker to the LP-6 brackets
- The three holes in the back of the LP-6 brackets allow to adjust the tilt angle (-7.5°, 0° or +7.5°).
For more information please refer to LP-6 user manual.
LP-6 BRACKETS STACK MOUNT
For the stack installation with LP-6 brackets follow this procedure:
- First remove the IS 210L side panels and internal link brackets
- Fasten the LP-6 brackets to the subwoofer
- Place the loudspeaker upside down on the subwoofer and fasten to the brackets
- The three holes in the back of the brackets allow to adjust the tilt angle (-7.5°, 0° or +7.5°).
For more information please refer to LP-6 user manual.
CONFIGURATIONS
For further information regarding max loading and installation requirements, please refer to the accessories user manual.
WARNINGS
WARNING: Make sure that the loudspeaker is securely installed in a stable
position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without
proper fastening systems. Before hanging the loudspeaker check all the
components for damages, deformations, missing or damaged parts that may
compromise safety during installation.
If you use the loudspeakers outdoor avoid spots exposed to bad weather
conditions. The external wiring connected to speaker output terminals requires
installation by qualified personnel only. Once the equipment is installed,
prevent access to the connectors
to unqualified personnel. Only use the accessories and configurations
described in this manual, and proceed in accordance with the instructions
given in the manuals for the accessories. dBTechnologies will not accept any
responsibility for damages caused by inappropriate accessories or additional
devices.
Installation and use of this equipment and its accessories must be performed
only by “Expert personnel” according to safety standard. To prevent hazards to
people, animals and/or objects, make sure that the installation is stable and
secure. Comply with the safety regulations and laws in force in the country in
which you use the product. For safe use, periodically check that all parts are
in good working condition before use. Only authorised personnel may carry out
design, calculations, installation, testing and maintenance of professional
flown or stacked audio systems.
Check periodically the integrity and the functionality of the accessories and
the technical equipments for a safe installation. user should never apply a
load that exceeds the working load limits of any rigging components or
equipment here presented. design, calculation, installation, testing and
maintanance of suspension and stack systems for audio equipment must be
performed only by qualified and authorized personnel. AEB Industriale s.r.l.
denies any and all responsibility for improper installations, in the absence
of safety requirements.
Features, specification and appearance of products are subject to change
without notice.
dBTechnologies reserves the right to make changes or improvements in design or
manufacturing without assuming any obligation to change or improve products
previously manufactured.
Scan with your QR Reader App to download the complete User Manual.
https://www.dbtechnologies.com/qrcode/001099/
A.E.B. Industriale Srl
Via Brodolini, 8
Località Crespellano
40053 VALSAMOGGIA
BOLOGNA (ITALIA)
Tel. +39 051 969870
Fax +39 051 969725
www.dbtechnologies.com
info@dbtechnologies-aeb.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>