Mircom MPS-800MP Fire Alarm Manual Station Instruction Manual

: June 4, 2024
: Mircom

Mircom MPS-800MP Fire Alarm Manual Station Instruction Manual

Mircom

Mircom’s MPS-800MP(U) Series Fire Alarm Manual Stations provide manual fire alarm activation.

This guide covers these models:

MPS-810MP Single Stage, Dual Action, MP Addressable Manual Station
MPS-810MPU Single Stage, Dual Action, MP Addressable
Manual Station (US)
MPS-802MP Two Stage, Dual Action, MP Addressable Manual

Station

MPS-822MP Two Stage, Dual Action, MP Addressable Manual Station with additional door contacts.

Specifications & Dimensions

Compatible with FX-400 series and FleX-Net™ FX-4000 Fire
Alarm Control Panels
Electrical Rating:
Nominal Operating Voltage: 15-30 VDC
Maximum alarm current: 3.3 mA
Standby current: 2 mA

Electrical Rating for MPS-822MP maglock terminal:

1A at 30VDC

Dimensions:

139 mm H x 104 mm W x 34 mm D (5 1/2” H x 4 1/8” W x 1 3/8” D)

Notes

Environment: Indoor, dry
Do not change factory applied finishes.
Wire as shown so that supervision of connections is maintained.
Maximum wire size: 14 AWG
ADA compliant.
To be installed per ADA 4.27.1 to 4.27.4 inclusive.
Wiring must be in accordance with CSA C22.1, Canadian
Electrical Code, Part I, Safety Standard for Electrical Installations, Section 32 and CAN/ULC-S524, Standard for Installation of Fire Alarm Systems.
All manual fire alarm stations shall be installed as per the specific requirements outlined in the UL/ULC codes, as well as all other applicable national or local codes. Final acceptance is subject to the local authority having jurisdiction.

Install the manual station

Contents of kit

MPS-810MP(U): 2 mounting screws, 2 reset keys (black)
MPS-802MP and MPS-822MP: 2 mounting screws, 2 reset keys (black), 2 stage two keys

A. Open

Insert the reset key into the reset keyhole and turn it.
Pull the cover open.

Figure 1 Front of manual station

Figure 2 Opening the station

Canada

25 Interchange Way
Vaughan, ON L4K 5W3
Tel: 1-888-647-2665

B. Wire

Note: The maximum wire size is 14 AWG.

Strip wires to 10 mm (25/64”) maximum.
Push the wire into the terminal.
Note: The terminals have a push-in lock. To remove the wire, push the terminal in with the screwdriver and pull out the wire at the same time. see Figure 3.

Figure 3 Removing the wire 3. Wire as shown in Figure 4.

Figure 4 Wiring

C. Mount
Flush mount indoor: Single-gang electrical box.
Surface mount indoor: BB-800 backbox with or without STI-1230
(Deep Cover without Gasket)
Note: Mount the manual station with the Mircom logo on the bottom.

]

Figure 5 Back of manual station

Fire Alarm Manual Station

D. Set the addressable module
Follow the instructions in LT-6146, the MIX-4090 Device
Programmer Installation Manual, available on http://www.mircom.com.
The factory default address is 255.
The connector for the device programmer is inside the unit above the addressable module, as shown in Figure 6.

Figure 6 Connector for device programmer

Using the manual station

Activate the alarm

Push in the push bar.
Pull down the pull handle.

A qualified person must reset the station by opening it with the
reset key. See Resetting the manual station below.

Activate the stage two alarm (MPS-802MP and

MPS-822MP)

Insert the stage two key into the stage two keyhole, and then turn the key.
The stage two alarm activates immediately.

Note: The stage two alarm will activate automatically a certain amount of time after the handle has been pulled if no action is taken. This time is set in the Fire Alarm Control Panel.