PARKSIDE PTPU 1500 A1 Pond Pump Instruction Manual

Instruction Manual

POND PUMP PTPU 1500 A1
TEICHPUMPE PTPU 1500 A1
POMPE POUR BASSIN PTPU 1500 A

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device

Table of pictograms use

| Read the operating instructions for this product attentively and with care before use.
---|---
| Important note!
| Observe warnings and safety instructions!
| Warning: Risk of electric shock! Danger to life!
IP68| Protection type
| Direct current
50 Hz| Frequency of 50 Hertz
V ∼| Alternating voltage in volt
| Dispose of the device and packaging in an environmentally friendly manner!
| Made from recycled material
---|---
| Do not dispose of any electrical devices in domestic waste!

Pond pump PTPU 1500 A1

 Introduction

Congratulations! You have purchased one of our high-quality products. During production, this device was checked for quality and subject to a final inspection. This ensures that your device is working properly. It is possible that, in individual cases, there may be residual water or lubricant on or in the device. This is not a defect or fault and is not a cause for concern. Please familiarise yourself with the product before using it for the first time. To do so, please read through the following operating and safety instructions carefully. Only trained persons may start up this product.

KEEP OUT OF THE REACH OF CHILDREN!
Intended use
The Parkside pond pump (hereafter referred to as “pump”) is designed for pumping water with a temperature between 4 °C and 35 °C. The pump is not frost-resistant and must be protected against frost. Possible applications are recirculating and pumping the water out of smaller ponds and aquariums, the creation of streams, where the water is being pumped from one reservoir into another reservoir at a higher position or the operation of water filters. The device is only intended to pump water. The device is not suitable for pumping dirty water with granular dirt or suspended particles or other liquids of any type such as, for example, petrol, diesel, solvents, etc.
Keep these instructions in a safe place. Ensure you hand over all documentation when passing the product on to anyone else. Any use that differs to the intended use as stated above is prohibited and potentially dangerous. If there are individuals in the water, then the device must not be used. There is a risk of electric shock. The operator or user is responsible for accidents or injury to other people or their property. The manufacturer is not liable for any injury or damage resulting from improper use or incorrect operation. This device is not suitable for commercial use. Commercial use will void the guarantee.
Scope of delivery
1 pond pump incl. 230V mains cable
1 nozzle connector, 13 mm
1 nozzle connector, 16 mm
1 set of operating instructions

Equipment
NOTE: After unpacking the product, please check that all of the package contents are present and that the pond pump is in perfect condition. Do not use the device if it is defective.
To do this see Fig. A, B, and C:

NOTE: The use of the term ‘product’, ‘device’, or ‘pump’ in the following text refers to the pond pump named in these operating instructions.

Technical Specifications

NOTE: The maximum pumping height and maximum water flow per hour are specific values for the pump. In reality, these values may be reduced by the nozzle connector used and by using nozzles,  oses, and similar components which are connected to the pump. These types of connections increase the flow resistance of the water against which the pump has to work. Changes to technical and visual aspects of the product may be made as part of future developments without notice. Accordingly, no warranty is offered for the physical dimensions, information, and specifications in these operating instructions. The operating instructions cannot, therefore, be used as the basis for asserting a legal claim.

Safety instructions

• Before starting work, familiarise yourself with all operating elements, in particular with the functions and mechanisms. If necessary ask a professional. Read and follow the operating instructions for the device.

• ATTENTION! If the mains cable is damaged or cut through, unplug the mains plug immediately from the socket.

• ATTENTION! The surface of the pump may get warm during operation! RISK OF BURNS!

• DANGER OF ELECTRIC SHOCK! If there are individuals in the water, then the device must not be used. There is a risk of electric shock.

• Only connect the device to a socket with RCD (Residual Current Device) with a rated residual current of no more than 30 mA; fuse of at least 6 Ampere.

• If the main cable for this device becomes damaged, ensure that the cable is replaced by the manufacturer, a customer service technician, or another qualified person to avoid any possible hazards.

• This device may be used by children aged 8 years and above, and by persons with reduced physical, sensory or mental capacities, or a lack of experience and/or knowledge if they are supervised or have been instructed in how to use the device safely and have understood the dangers that may arise when using it. Do not allow children to play with the device. Cleaning and maintenance work must not be carried out by children unless they are being supervised.

• Children must be supervised to ensure that they do not play with the device.

• ATTENTION! Prevent the pump from running dry! Risk of overheating! Risk of material damage! Electrical appliances must not be disposed of in the household waste.

• Follow the further instructions in the “Maintenance and cleaning” chapter, as well as the “Storage” chapter.
  CAUTION! HOW TO AVOID ACCIDENTS AND INJURIES:

• Individuals who are not familiar with the operating instructions must not use the device. Local regulations may specify the minimum age for the operating personnel.

• Wear sturdy shoes to protect against electric shock.

• Take appropriate measures to keep children away from the device when it is running. There is a risk of injury.

• Do not operate the device near flammable liquids or gases.
  Failure to do so risks causing a fire or explosion.

• Keep the device in a dry location and out of the reach of children when it is not being used.
  CAUTION! HOW TO AVOID DAMAGE TO THE DEVICE AND ANY HARM TO PERSONS THAT MAY RESULT FROM SUCH DAMAGE:

• You must not pump aggressive, abrasive/grinding (e.g. and water), corrosive, flammable (e.g. automotive fuels) or explosive liquids, salt water, detergents, and foodstuffs. The temperature of the liquid being pumped must not exceed 35 °C. Not complying with this may cause damage to the device and expose the user to a risk of injury.

• Do not work with damaged, incomplete devices or those which have been modified without the approval of the manufacturer. Before using the device, a specialist should carry out a check to make sure that the electrical protective measures required are in place.

• Supervise the device when it is being used, in order to identify in good time if the pump is running dry. Failure to do so will void any warranty and liability claims.

• Check the device regularly to make sure it is functioning properly.

• Do not carry or fix the device using the main cable or the hose.

• Protect the device from frost and running dry.

• Only use original accessories and do not carry out any modifications to the device.

• Please read the instructions in the operating instructions on the subject of “Maintenance and cleaning”. All additional measures must be carried out by a qualified electrician. Always contact our Service Centre if you need any repairs.

ELECTRICAL SAFETY:

CAUTION: How to avoid accidents and injuries from electric shock:

• When operating the device, the main plug must be freely accessible once the device is installed.

• Before you start using your new pump, get it professionally checked:
  – Earthing, zeroing, and residual current protection circuit must meet the safety regulations of the energy supply company and be working perfectly,
  – Protection of the electrical plug connections against moisture.

• If there is a risk of flooding, mount the plug connections in an area that cannot flood.
  RISK OF ELECTRIC SHOCK:

• Make sure that the mains voltage matches the specifications on the type plate.

• Carry out the electrical installation in accordance with the national regulations.

• Before each use, check the device’s mains cable and mains plug for damage. Defective main cables must not be repaired, instead, they must be replaced with new ones. Have any damage to your  device repaired by an authorized specialist.

• Do not use the mains cable to unplug the mains plug from the socket. Protect the mains cable from heat, oil, and sharp edges.

• Do not carry or fix the device using the main cable.

• Only use extension cables that are splashproof and intended for outdoor use. Always fully unroll a cable reel before use. Check the cable for damage.

• Unplug the mains plug from the socket before carrying out any work on the device, if there are leaks in the water system and when not being used.

• Extension cables must not have a smaller cross-section than rubber hose lines marked with H07RN8-F. The cable length must be 10 m.
  The strand cross-section of the extension cable must be at least 2.5 mm².
  ATTENTION! NOT SUITABLE FOR DRINKING WATER

Before using the device

• Prevent the pump from 1 running dry. Failure to do so will void any warranty and liability claims. Ensure that the electrical connection is 230 V~ 50 Hz.
• Check that the electrical socket is in good condition and that it is sufficiently fused (at least 6 A, RCD switch).
• Ensure there is no way that moisture or water can reach the main connection. There is a risk of electric shock.
  NOTE: Ensure that the power cable forms a loop below the mains plug, in order to prevent water from running into the plug via the cable.

Using the device

• Check whether the position for pump 1 is secure and fix pump 1 onto the supporting surface before you use it. For smooth supporting surfaces, you can use the suction pads 3 on the
  the underside of the pump 1 to do this.

• Depending on the application, connect the right hose with the pump 1.

• Make sure that the hose connections are tight. If necessary, use hose clamps (not included in the scope of delivery). Select either the 13 mm 6 or 16 mm 7 nozzle connector to fit the hose diameter.

• Make sure that there are no air bubbles trapped in the hose. These would have a negative effect on the power. To do this, lay the hose so that it ascends and avoids loops.

• Position the pump 1 fully below the surface of the water, ideally at least 10 cm under the water level. Align pump 1 so that it is as level and horizontal as possible.

• Do not place pump 1 directly onto slimy or sandy surfaces. The ideal position is for it to be raised, such as, for example, on a stone.

• Never use pump 1 without the filter grille 5. This prevents the ingress of coarse dirt which would damage the pump 1.

• By rotating the filter grille5 you can regulate the flow rate. Turning clockwise: less flow; Turning anti-clockwise: more flow. (see Fig. C)

• In order to achieve the very best pumping results, pump 1 must be positioned on a flat surface.

• Only allow pump 1 to operate when it is completely submerged in water.

• If you use pump 1 in an ornamental pond, position pump 1 in an area that is as free of sand as possible.

NOTE: In order to achieve the maximum water flow, you must keep the hoses as short as possible.
Also, as far as possible there should be no kinks and/or large height differences. Ideally, you should use hoses with the largest possible diameter, in order to achieve the greatest possible water flow rate.

 Maintenance and cleaning

• Pump 1 has been manufactured in a reliable, high-quality design, where the non-contact pump wheel mechanism ensures a long period of operation. However the pump wheel unit 9 is susceptible to contamination from the operating environment and must not be damaged.

**CAUTION:** In order to clean pump 1 or carry out maintenance work, always disconnect it first by unplugging the mains plug 2 from the voltage supply. There is a risk of electric shock or risk of injury through moving parts.

• Always keep the mains plug 2 dries before you connect the pump 1 back to the mains power socket. In case of doubt, please contact your electrical specialist.
• In order to clean pump 1 , remove the front cover 4 and the pump wheel unit 9. To lift off the front cover 4 use a narrow flat-blade screwdriver to help you, if necessary. The round cover of the pump wheel unit 8 has a bayonet connector and can be undone by turning it anti-clockwise. The pump wheel unit  9 will simply be pulled out forwards. Use a small, soft brush or a water jet to remove any dirt which is stuck.

**CAUTION: The pump shaft cannot be removed. Re-assemble pump 1** after cleaning by following the instructions in reverse order.

• Monthly maintenance will increase the service life of the pump 1.

Troubleshooting

If pump 1 does not work, check the following:

1. Check that there is sufficient water around pump 1.

2. Check the residual current protection switch off your mains socket and use another socket o make sure that pump 1 is being properly supplied with power.
   NOTE: Always unplug the mains plug from socket 2 before you touch pump 1.

3. If, when the pump is running, you can hear abnormal noises, check the pump wheel unit 9.
   To do this, unscrew the nozzle connector 6 or 7 from the pump in order to obtain access to the pump wheel. Rotate the pump wheel unit 9 to make sure that it is not broken or blocked. If there is a crack or surface damage on the pump wheel unit 9 , contact an authorized service point.

with the instructions in the “Maintenance and cleaning” chapter.
Insufficient pumping capacity| Housing is clogged with dirt| Clean pump 1 in accordance with the instructions in the “Maintenance and cleaning” chapter.
Heavy loss in the pipes| Check for leaks, excessive height differences, kinked hoses, etc.
Pump 1 switches off after a short time| Excessively contaminated water| Clean pump  1 fits a filter in, and the system
Excessive water temperature| Ensure that the water temperature does not exceed 35 °C.

Storage

• Keep the device clean and dry and out of the reach of children.
• Protect the device from frost.
• If you are not going to use the pump for a longer period of time, then you must clean the device thoroughly after the last use and before using it again. Otherwise, it may be difficult to start the device because of deposits or residues.

Information about recycling and disposal

DON’T THROW AWAY – RECYCLE!
According to European Directive 2012/19/EU, used electrical devices must be collected separately for environmentally compatible recycling or recovery. Please return this device to an approved waste management company or use your municipal waste collection service. Please ensure you comply with local regulations. If you have any questions, please contact your local authority or waste management company.
Please return this device, accessories, and packaging to your local recycling depot. Do not dispose of electrical appliances in household waste! This satisfies your legal obligations while also making an important contribution to protecting the environment.
Please note the marking on the different packaging materials and separate them as necessary.
The packaging materials are marked with abbreviations (a) and digits (b) with the following definitions: 1–7: Plastics, 20–22: Paper and cardboard, 80–98: Composite materials.

EC Declaration of Conformity
We,
C. M. C. GmbH
Responsible for documentation:
Dr. Christian Weyler
Katharina-Loth-Str. 15
66386 St. Ingbert
GERMANY

hereby take sole responsibility for declaring that the product
Pond pump

IAN:
Art. no.:
Year of manufacture:
Model:| 388427_2107
2447
2022/14
PTPU 1500 A1
---|---

meets the basic safety requirements as specified in the European Directives
Electromagnetic Compatibility:
(2014/30/EU)
Machinery Directive:
(2006/42/EC)
RoHS Directive:
(2011/65/EU)+(2015/863/EU)   and the amendments to these Directives.
The object of the declaration described above meets the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
This conformity assessment is based on the following harmonized standards:

EN 55014-1:2017/A11:2020
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013/A1:2019
EN 60335-1:2012/A2:2019
EN 60335-2-41:2003/A2:2010
EN 62233:2008
EN IEC 63000:2018
St. Ingbert, 01.10.2021

Dr. Christian Weyler
– Quality Assurance –

Warranty and service information
Warranty from Creative Marketing & Consulting GmbH
Dear Customer,
The warranty for this equipment is 3 years from the date of purchase. In the event of product defects, you have legal rights against the retailer of this product. Your statutory rights are not affected in any way by our warranty conditions, which are described below.
Warranty conditions
The warranty period begins on the date of purchase. Please retain the original sales receipt.
This document is required as your proof of purchase.
Should this product show any defect in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our discretion – free of charge.
This warranty service requires that you retain the proof of purchase (sales receipt) for the defective device for the three-year period and that you briefly explain in writing what the fault entails and when it occurred.
If the defect is covered by our warranty, we will repair and return your product or send you a replacement.
The original warranty period is not extended when a device is repaired or replaced.

The warranty period and statutory claims for defects
The warranty period is not extended by the guarantee. This also applies to replaced and repaired parts.
Any damages or defects detected at the time of purchase must be reported immediately after unpacking.
Any incidental repairs after the warranty period are subject to a fee.
Extent of warranty
This device has been manufactured according to strict quality guidelines and carefully inspected before delivery.
The warranty applies to material and manufacturing defects only. This warranty does not extend to product parts, which are subject to normal wear and tear and can thus be regarded as consumable parts, or for damages to fragile parts, e.g. switches, rechargeable batteries, or parts made from glass.
This warranty is voided if the product becomes damaged or is improperly used or maintained.
For proper use of the product, all of the instructions given in the operating instructions must be followed precisely. If the operating instructions advise you or warn you against certain uses or actions,  these must be avoided in all circumstances.
The product is for consumer use only and is not intended for commercial or trade use. The warranty becomes void in the event of misuse and improper use, use of force, and any work on the device that has not been carried out by our authorized service branch.
Processing of warranty claims
To ensure prompt processing of your claim, please follow the instructions given below.
Please retain the proof of purchase and the article number (e.g. IAN) for all inquiries.
The product number can be found on the type plate, an engraving, the cover page of your instructions (bottom left), or the sticker on the back or underside of the device.
In the event of malfunctions or other defects, please first contact our service department below by phone or email. If your product is found to be defective, you can then send your product with proof of purchase (till receipt) and a statement describing what the fault involves and when it occurred free of charge to the service address given.
NOTE: You can download this handbook and many more, as well as product videos and software at www.lidl-service.com.

www.lidl-service.com

With this QR code, you can gain immediate access to the Lidl Service page (www .lidl-service.com) and you can open your operating instructions by entering the article number (IAN) 388427.

Service
How to contact us:

Name:
Website:
E-mail:
Phone:
Registered office| C. M. C. GmbH
www.cmc-creative.de
service.gb@cmc-creative.de
0-808-189-0652
Germany
---|---

IAN 388427_2107
Please note that the following address is not a service address. Please first contact the service point
given above.
C. M. C. GmbH
Katharina-Loth-Str. 15
66386 St. Ingbert
GERMANY
Ordering spare parts:
www.ersatzteile.cmc-creative.de

C.M.C. GmbH
Katharina-Loth-Str. 15
DE-66386 St. Ingbert
GERMANY
Last Information Update
· Stand der Informationen

References

• Creative.DE - creative Produkte und Dienstleistungens
• dragomans.com is for sale!
• service.com is for sale | www.brandforce.com
• C.M.C Creative Marketing & Consulting GmbH | Home
• Parkside Spareparts
• Home Page-EN
• de/
• RIKUSHOP.IT – Rikushop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>