aruba 650 Series Campus Access Points Installation Guide
- June 3, 2024
- aruba
Table of Contents
650 Series Campus Access Points
Installation Guide
The Aruba 650 Series Campus access points are high-performance, multi-radio
wireless devices that can be deployed in either controller-based (ArubaAOS)
or controllerless (InstantOS) network environments. These access points
support the 802.11ax standard in the 2.4GHz, 5GHz, and 6GHz bands with a 4×4
MIMO tri-radio WI-Fi 6E platform. Additionally, 650 Series Campus access
points provide dual wired 5Gbps Smart Rate
Ethernet network interfaces enhance their performance and client capacity.
Hardware Overview
Figure 1 AP-655 Access Point Front View
Figure 2 AP-655 Access Point Side and Rear View
Figure 3 AP-655 Access Point Bottom View
1 | E0 Ethernet Port |
---|---|
2 | E1Ethernet Port |
LED
The LED displays located on the front panel of the access point indicate the
system status of the access point.
System Status LED
Table 1: System Status LED
Color/State | Meaning |
---|---|
Off | Device Powered off |
Green- solid 1 | Device ready, fully functional, no network restrictions |
Green- blinking 2 | Device booting, is not ready |
Green- flashing off 3 | Device ready, fully functional, either uplink |
negotiated in sub-optimal speed (<1Gbps)
Green- flashing on| The device in deep-sleep mode
Amber- solid| Device ready, restricted power mode (limited PoE power
available, or IPM restrictions applied), no network restrictions
Amber- flashing off| Device ready, restricted power mode (limited PoE power
available, or IPM restrictions applied), uplink negotiated in sub-optimal
speed (<1Gbps)
Red| System error condition – Immediate attention required
- Blinking: one second on, one second off, 2 seconds cycle.
- Flashing off: mostly on, a fraction of a second off, 2 seconds cycle.
- Flashing on: mostly off, a fraction of a second on, 2 seconds cycle.
Radio Status LED
Table 2: Radio Status LED
Color/State | Meaning |
---|---|
Off | The device powered off, or the radio disabled |
Green- solid | Radio enabled in access (AP) mode |
Green- flashing off | Radio enabled in uplink or mesh mode |
Amber- solid | Radio enabled in monitor or spectrum analysis mode |
LED Display Settings
The LEDs have three operating modes that can be selected in the system
management software:
- Default mode: refer to Table 1 and Table 2.
- Off mode: all LEDs are off
- Blink mode: all LEDs blink green (synchronized)
To force the LEDs into off mode or back to software-defined mode, press the
reset button for a short duration (less than 10 seconds).
Bluetooth Low Energy Radios
650 Series access points are equipped with an integrated BLE and 802.15.4
radio that provide the following capabilities:
- location and asset-tracking applications
- wireless console access
- IoT gateway applications
Console Port
The console port is a Micro-B connector located on the back of this device.
Use the proprietary AP-CBL-SERU cable or AP-MOD-SERU module (sold separately)
for direct management of this device when connected to a serial terminal or
laptop. For pin-out details, refer to Figure 4.
Figure 4 Micro-B Port Pin-out
Ethernet Ports
The 650 Series Campusaccess points are equipped with two 100/1000/2500/5000
Base-T auto-sensing MDI/MDX wired RJ45 Ethernet ports (E0 and E1). The 2.5bps
speed complies with NBase-T and 802.3bz specifications. Both ports are
compliant with 802.3ab 1000Base-T Gigabit Ethernet and 802.3az (Energy
Efficient Ethernet) standards. Both ports support 802.3af, 802.3at, and
802.3bt Power over Ethernet compliance to accept power from a POE source,
such as a PoE midspan injector, or a network switch.
The 650 Series access points are equipped with two active Ethernet ports (Eth0
and Eth1) (link to figure). Both ports are 100/1000/2500/5000 Base-T, auto-
sensing MDI/MDX, which supports uplink connectivity when linked by an Ethernet
cable. Refer to Figure 5 for a detailed port pin-out.
Figure 5 Ethernet Port Pin-Out
The 650 Seriesaccess points are equipped with two Ethernet ports (E0 and E1):
- E0 port: 100/1000/2500Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port
- E1 port: 100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port
Kensington Lock Slot
The 650 Series is equipped with a Kensington lock slot for additional physical
security.
USB Interface
The USB 2.0 interface located on the top of the is 650 Series compatible with
selected cellular modems and other peripherals. When active, this port can
supply up to 5W/1A to a connected device.
Figure 6 650 Series USB
Reset Button
The reset button located on the bottom of the device can be used to reset the
access point to factory default settings or turn off/on the LED display.
Use one of the following methods to reset the access point to the factory
default settings:
-
To reset during normal operation:
• Hold the reset button for more than 10 seconds while the access point is running.
• Release the reset button. -
To reset during power-up, hold the reset button while the access point is powering up.
The system status LED will flash again within 15 seconds indicating that the
reset is completed. The access point will now continue to boot with the
factory default settings.
To toggle the LED display between Off and Blinking, during the normal
operation of the access point, shortly press and release the reset button
using a small, narrow object, such as a paperclip.
Power
Both Ethernet ports support PoE-in, allowing the AP to draw power from an
802.3at/802.3bt PoE power source. When the AP is powered by both E0 and E1
ports simultaneously, the AP can be configured by management software to
source PoE power from either port or to combine the power from both ports.
If PoE is not available, a proprietary AP-AC2-12B power adapter or AP-AC2-48C
adapter (sold separately) can be used to power the access point. When both PoE
and DC power sources are available, the DC power source takes precedence. In
that case, the access point simultaneously draws a minimal current from the
PoE source.
In the event that the DC source fails, the access point switches to the PoE
sources.
The 650 Series access points support the Intelligent Power Monitoring (IPM)
feature, to report AP power consumption and enable intelligent management of
power-save capabilities.
Table 3 lists operational restrictions when the AP is powered by different
power options.
Table 3: Power Options and Operational Restrictions
Power Source | IPM | Restrictions |
---|---|---|
1 x 802.3bt PoE | n/a | No restrictions, all capabilities available. |
2 x 802.3at PoE | n/a | No restrictions, all capabilities available. |
1 x 802.3at PoE | enabled | AP starts up in unrestricted mode, but may |
dynamically apply restrictions depending on the PoE budget and actual power.
1 x 802.3at PoE| disabled| The second (other) Ethernet port is disabled.
1 x 802.3af PoE| n/a| AP does not start up, red system LED.
DC power| n/a| No restrictions, all capabilities are available
PoE 802.3bt| n/a| No restrictions and all capabilities are available
PoE 802.3at| disabled| USB disabled (can be overruled in software)
PoE 802.3af| disabled| USB disabled (can be overruled in software), AP in dual
radio mode, El or EO disabled (one without PoE or El), remaining wired port
limited to 1Gbps.
PoE 802.3at| enabled| All capabilities available (features may be disabled per
IPM configuration)
PoE 802.3af| enabled| All capabilities available (features may be disabled per
IPM configuration)
Before You Begin
Refer to the sections below before beginning the installation process
FCC Statement: Improper termination of access points installed in the United
States configured to non-US model controllers will be in violation of the FCC
grant of equipment authorization. Any such willful or intentional violation
may result in a requirement by the FCC for immediate termination of operation
and may be subject to forfeiture (47 CFR 1.80).
Pre-Installation Checklist
Before installing your
-
Cat5E or better UTP cable with network access
-
A compatible PoE injector with a power cord
One of the following network services: -
Aruba Discovery Protocol (ADP)
-
DNS server with an “A” record
-
DHCP Server with vendor-specific options
Aruba, in compliance with governmental requirements, has designed the 650
Series access points so that only authorized network administrators can change
configuration settings. For more information about AP configuration, refer to
the Software Quick Start Guide.
Access points are radio transmission devices and as such are subject to
governmental regulation. Network administrators responsible for the
configuration and operation of access points must comply with local broadcast
regulations. Specifically, access points must use channel assignments
appropriate to the location in which the access point will be used.
Identifying Specific Installation Locations
Use the access point placement map generated by the Aruba RF Plan software
application to determine the proper installation location(s). Each location
should be as close as possible to the center of the intended coverage area and
should be free from obstructions or obvious sources of interference. These RF
absorbers/reflectors/interference sources will impact RF propagation and
should be accounted for during the planning phase and adjusted for in the RF
plan.
Use of this equipment adjacent to or stacked with other equipment should be
avoided because it could result in improper operation. If such use is
necessary, this equipment and the other equipment should be observed to
verify that they are operating normally.
Identifying Known RF Absorbers/Reflectors/Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in
the field during the installation phase is critical. Make sure that these
sources are taken into consideration when you attach an access point to its
fixed location.
RF absorbers include:
-
Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals.
-
Natural Items—Fish tanks, water fountains, ponds, and trees
-
Brick
RF reflectors include: -
Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.
-
Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances.
RF interference sources include:
- Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)
- Cordless headsets such as those used in call centers or lunch rooms
Access Point Installation
All Aruba access points should be professionally installed by an Aruba-
Certified Mobility Professional (ACMP). The installer is responsible for
ensuring that grounding is available and meets applicable national and
electrical codes.
Failure to properly install this product may result in physical injury and/or
damage to property.
For indoor use only. The access point, AC adapter, and all connected cables
are not to be installed outdoors. This stationary device is intended for
stationary use in partly temperature-controlled weather-protected environments
(class 3.2 per ETSI 300 019).
Software
Aruba 650 Series requires ArubaOS or Aruba Instant 8.8 or later. For
instructions on choosing operating modes and initial software configuration,
refer to the Software Quick Start Guide.
Aruba access points are classified as radio transmission devices and are
subject to government regulations of the host country. The network
administrator(s) is/are responsible for ensuring that the configuration and
operation of this equipment is in compliance with their country’s regulations.
For a complete list of approved channels in your country, refer to the Aruba
Downloadable Regulatory Table at
https://www.arubanetworks.com/techdocs/DRT/Default.htm.
Verifying Post-Installation Connectivity
The integrated LEDs on the access point can be used to verify that the access
point is receiving power and initializing successfully (see Table 1 and Table
2). Refer to the AP Software Quick Start Guide for further details on
verifying post-installation network connectivity.
Electrical and Environmental Specifications
Electrical
- Ethernet
• E0: 100/1000/2500Base-T auto-sensing Ethernet RJ-45 Interfaces
• E1: 100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces
• Power over Ethernet (IEEE 802.3at and 802.3bt compliant)
If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an output rated 48V DC, minimum 0.75A, marked “LPS” and “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada.
Environmental
-
Operating
• Temperature: 0°C to +50°C (+32°F to +122°F)
• Humidity: 5% to 93% non-condensing -
Storage
• Temperature: -40ºC to 70ºC (-40ºF to 158ºF)
• Humidity: 5% to 93% non-condensing
Regulatory Model Number
For the purpose of regulatory compliance certifications and identification,
this product has been assigned a unique regulatory model number (RMN). The
regulatory model number can be found on the product nameplate label, along
with all required approval markings and information. When requesting
compliance information for this product, always refer to this regulatory model
number. The regulatory model number RMN is not the marketing name or model
number of the product.
The following regulatory model numbers apply to the 650 Series
- AP-655 RMN: APIN655
Safety and Regulatory Compliance
RF Radiation Exposure Statement: This equipment complies with RF
radiation exposure limits. This equipment should be installed and operated
with a minimum distance of 13.78 inches (35cm) between the radiator and your
body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
The device could automatically discontinue transmission in case of the
absence of information to transmit or operational failure. Note that this is
not intended to prohibit the transmission of control or signaling information
or the use of repetitive codes where required by the technology.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
United States
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio or TV technician for help.
Improper termination of access points installed in the United States configured to a non-US model controller is a violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
FCC regulations restrict the operation of this device to indoor use only.
The operation of this device is prohibited on oil platforms, cars, trains,
boats, and aircraft, except that operation of this device is permitted in
large aircraft while flying above 10,000 feet.
Operation in the 5.9725-7.125GHz band is prohibited for control of or
communication with unmanned aircraft systems
Industry Canada
This Class B digital apparatus meets all of the requirements of the Canadian
Interference-Causing Equipment Regulations.
In accordance with Industry Canada regulations, this radio transmitter and
receiver may only be used with an antenna, the maximum type and gain of which
must be approved by Industry Canada. To reduce potential radio interference,
the type of antenna and its gain shall be chosen so that the equivalent
isotropic radiated power (EIRP) does not exceed the values necessary for
effective communication.
This device complies with Industry Canada’s license-exempt RSS regulations.
Operation of this device is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation.
When operated in the 5.15 to 5.25 GHz frequency range, this device is
restricted to indoor use to reduce the potential for harmful interference with
co-channel Mobile Satellite Systems.
EU Regulatory Conformance
The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU
is available for viewing at:
www.hpe.com/eu/certificates. Select the
document that corresponds to your device’s model number as it is indicated on
the product label.
Compliance is only assured if the Aruba-approved accessories as listed in the
ordering guide are used.
https://www.arubanetworks.com/assets/og/OG_650Series.pdf.
Wireless Channel Restrictions
5150-5350MHz band is limited to indoors only in the following countries;
Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech
Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany
(DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT),
Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT),
Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO),
Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH),
Turkey (TR), United Kingdom (UK) (NI).
Radio | Frequency Range MHz | Max EIRP |
---|---|---|
BLE/Zigbee | 2402-2480 | 9 dBm |
2412-2472 | 20 dBm | |
5150-5250 | 23 dBm | |
Wi-Fi | 5250-5350 | 23 dBm |
5470-5725 | 30 dBm | |
5725-5850 | 14 dBm |
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Instant User Guide for details on restrictions.
Medical
- Equipment not suitable for use in the presence of flammable mixtures.
- Connect to only IEC 60950-1 or IEC 60601-1 certified product and power sources. The end user is responsible for the resulting medical system that complies with the requirements of IEC 60601-1.
- Wipe with a dry cloth, no additional maintenance is required.
- No serviceable parts, the unit must be sent back to the manufacturer for repair.
- No modifications are allowed without Aruba’s approval.
Ukraine
Hereby, Hewlett Packard Enterprise Company declares that the radio equipment
type [The Regulatory Model Number [RMN] for this device can be found in the
Regulatory Model Number section of this document] is in compliance with
Ukrainian Technical Regulation on Radio Equipment, approved by resolution of
the CABINET OF MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text
of the UA declaration of conformity is available at the following internet
address: https://certificates.ext.hpe.com/public/certificates.html.
Contacting Support
Table 4: Contact Information
Main Site | https://www.arubanetworks.com |
---|---|
Support Site | https://asp.arubanetworks.com |
Airheads Social Forums and Knowledge
Base| https://community.arubanetworks.com
North American Telephone|
1-800-943-4526 (Toll-Free)
1-408-754-1200
International Telephone| https://arubanetworks.com/support-services/contact-
support/
Software Licensing Site| https://hpe.com/networking/support
End-of-life Information| https://www.arubanetworks.com/support-services/end-
of-life/
Security Incident Response Team| https://www.arubanetworks.com/support-
services/securitybulletins/
Email: sirt@arubanetworks.com
Copyright
© Copyright 2021 Hewlett Packard Enterprise Development LP.
Open Source Code
This product includes code licensed under the GNU General Public License, the
GNU Lesser General Public License, and/or certain other open source licenses.
A complete machine-readable copy of the source code corresponding to such code
is available upon request.
This offer is valid to anyone in receipt of this information and shall expire
three years following the date of the final distribution of this product
version by Hewlett Packard Enterprise Company.
To obtain such source code, send a check or money order in the amount of US
$10.00 to:
Hewlett Packard Enterprise Company
Attn: General Counsel
6280 America Center Drive
San Jose, CA 94089
USA
Warranty
This hardware product is protected by an Aruba warranty. For more details,
visit www.hpe.com/us/en/support.html
References
- HPE Aruba Networking | Enterprise
- Security-first, AI-powered networking | HPE Aruba Networking
- Intelligent data center networks | HPE Aruba Networking
- Contact Support | HPE Aruba Networking
- HPE Aruba Networking | Enterprise
- Security Advisories | Aruba
- arubanetworks.com/techdocs/DRT/Default.htm
- hpe.com/us/en/support.html
- HPE Aruba Networking | Enterprise
- HPE Aruba Networking | Enterprise
- Aruba Support Portal
- Home - Airheads Community
- Home - Airheads Community
- Intelligent data center networks | HPE Aruba Networking
- Intelligent data center networks | HPE Aruba Networking
- HPE Aruba Networking | Enterprise
- Edge-to-Cloud Security | HPE Aruba Networking
- Security Advisories | HPE Aruba Networking
- arubanetworks.com/techdocs/DRT/Default.htm
- Regulations certificates | Hewlett Packard Enterprise
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>