Aruba AP-505 Installation Guide: Learn How to Install Campus Access Points
- June 6, 2024
- aruba
Table of Contents
The Aruba 500 Series AP-505 Campus Access Points Installation Guide provides detailed instructions on how to install and set up the Aruba 500 Series campus access points. These high-performance, dual-radio wireless devices can be deployed in both controller-based (ArubaOS) and controllerless (Aruba Instant) network environments. With concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi functionality, MIMO radios, and support for legacy wireless services, these access points deliver reliable and fast wireless connectivity. Additionally, they come equipped with a Bluetooth Low Energy (BLE) and Zigbee radio, enabling locationing and IoT services. The guide includes information on the package contents, hardware overview, LED display settings, power options, and pre-installation checklist. It also provides guidance on identifying specific installation locations and ensuring compliance with governmental requirements. The guide is an essential resource for anyone looking to install and configure the Aruba 500 Series campus access points.
Aruba 500 Series Campus Access Points Installation Guide
aruba 500 Series AP-505 Campus Access Points Installation Guide
The Aruba 500 Series campus access points (AP-504 and AP-505) are high- performance, dual-radio wireless devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant) network environments. These access points deliver high performance concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi functionality with MIMO radios (2×2 in 2.4 GHz, 2×2 in 5 GHz), while also supporting legacy 802.11a/b/g/n/ac wireless services.
In addition to both Wi-Fi radios, these APs also incorporate a Bluetooth Low Energy (BLE) and Zigbee radio, supporting a variety of use-cases and services, such as locationing and IoT. A mount kit (sold separately) is needed to mount the AP. Make sure to purchase the correct mount kit for the intended deployment of the AP.
Package Contents
- Aruba 500 Series access point (with a pre-installed mount bracket)
The AP mount bracket attaches to a variety of mount kits (sold
separately).
Inform your supplier if there are any incorrect, missing, or
damaged parts. If possible, retain the carton, including the original packing
materials. Use these materials to repack and return the unit to the supplier
if needed.
Hardware Overview
The following sections outline the hardware components of the 500 Series
access points.
Figure 1 AP-505 Front View![aruba 500 Series AP-505 Campus Access Points
- View](https://manuals.plus/wp-content/uploads/2022/02/aruba-500-Series- AP-505-Campus-Access-Points-View-300x300.png)
Figure 2 AP-504 Front View![aruba 500 Series AP-505 Campus Access Points
- View Figure 2](https://manuals.plus/wp-content/uploads/2022/02/aruba-500 -Series-AP-505-Campus-Access-Points-View-Figure-2-300x295.png)
External Antenna Connectors
The AP-504 access points are equipped with two external antenna connectors
located on the front corners of the access point (see Figure 2). Antenna ports
A0 and A1(corresponding with radio chain 0 and 1), are used for both radios
and bands (RF signals are diplexed).
External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or another Aruba-certified technician, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software. A list of approved antennas can be found at: http://www.arubanetworks.com/assets/og/OG_AP-500Series.pdf.
Figure 3 LEDs (AP-505 shown)
LEDs
System Status
The System Status LED indicates the operating condition of the access point.
Table 1 System Status LED
Color/State | Meaning |
---|---|
Off | Device Powered off |
Green- solid | Device ready, fully functional, no network restrictions |
Green- blinking 1 | Device booting, not ready |
Green- flashing off 2 | Device ready, fully functional, uplink negotiated in |
sub-optimal speed (<1Gbps)
Green- flashing on 3| Device in deep-sleep mode
Amber- solid| Device ready, restricted power mode (IPM restrictions applied),
no network restrictions
Amber- flashing off| Device ready, restricted power mode (IPM restrictions
applied), uplink negotiated in sub-optimal speed (<1Gbps)
Red| System error condition – Immediate action required
- Blinking: one second on, one second off, 2 seconds cycle.
- Flashing off: mostly on, fraction of a second off, 2 seconds cycle.
- Flashing on: mostly off, fraction of a second on, 2 seconds cycle.
Radio Status
The Radio Status LED indicates the operating mode of the access point’s
radios.
Table 2 Radio Status LEDs
Color/State | Meaning |
---|---|
Off | Device powered off, or both radios disabled |
Green- solid | Both radios enabled in access mode |
Green- blinking | One radio enabled in access mode, other disabled |
Amber- solid | Both radios enabled in monitor mode |
Color/State | Meaning |
--- | --- |
Amber- blinking | One radio enabled in monitor mode, other disabled |
Green/Amber-
alternating1| Green: one radio in access mode
Amber: one radio in monitor mode
1. Alternating: one second each color, 2 seconds cycle.
LED Display Settings
The LEDs have three operating modes that can be selected in the system
management software:
- Normal mode: Refer to Table 1and Table 2
- Off mode: LEDs are off
- Blink mode: LEDs blink green (synchronized)
Figure 4 AP-505 Rear View
Cable Guide
The cable guide on the rear of the access point is used to organize cables, as
shown in Figure 5. The use of the cable guide is optional and does not support
all types of cables and plugs.
Figure 5 Cable Guide
Bluetooth Low Energy and Zigbee Radio
500 Series access points are equipped with an integrated BLE and Zigbee radio
that provide the following capabilities:
- location beacon applications
- wireless console access
- IOT gateway applications
Console Port
The console port is a Micro-B connector located on the back of this device. A
proprietary serial adapter cable (APCBL-SERU) is needed to use this interface.
It is sold separately to connect the AP to a serial terminal or a laptop for
direct local management (a standard USB cable cannot be used for this
interface).
Ethernet Port
The Aruba 500 Series is equipped with a 10/100/1000Base-T auto-sensing MDI/MDX
Ethernet port (E0). This E0 port supports IEEE 802.3af and 802.3at Power over
Ethernet compliance, accepting power from a Power Sourcing Equipment (PSE)
such as a PoE midspan injector, or network infrastructure that support PoE.
Kensington Lock Slot
The 500 Series is equipped with a Kensington lock slot for additional physical
security.
USB 2.0 Interface
The top of this access point is equipped with a USB-A port that is compatible
with selected cellular modems and other peripherals. When active, this port
can supply up to 5W/1A to a connected device.
Reset Button
The reset button located on the back of the device can be used to reset the
access point to factory default settings or turn off/on the LED display.
There are two ways to reset the access point to factory default settings:
Reset the AP during normal operation press and hold down the reset button
using a small, narrow object such as a paper clip for more than 10 seconds
during normal operation.
Reset the AP while powering up
- Press and hold down the reset button using a small, narrow object such as a paper clip while the access point is not powered on (either via DC power or PoE).
- Connect the power supply (DC or PoE) to the access point while the reset button is being held down.
- Release the reset button on the access point after 15 seconds.
To turn off/on the LED display, press and release the reset button using a small, narrow object, such as a paperclip for less than 10 seconds during normal operation of the access point.
Power
E0 port supports PoE-in (AP is a PoE-PD device), allowing the device to draw power from compliant PoE power sources. If PoE is not available, a proprietary AP-AC-12V30B power adapter (sold separately) can be used to power the access point. When both PoE and DC power sources are available, the DC power source takes precedence. In that case, the access point simultaneously draws a minimal current from the PoE source. In the event that the DC source fails, the access point switches to the PoE sources.
The Intelligent Power Monitoring (IPM) feature may also be used to manage the
power consumption preferences for this device. When enabled, the user may
enable/disable power restrictions for the access point using Aruba’s AP
management software.
Table 3 lists operational restrictions when the access point is powered
by different power options.
Table 3 Power Options and Operational Restrictions
Power Source | IPM | Restrictions |
---|---|---|
DC power | n/a | No restrictions, all capabilities available |
PoE 802.3at | n/a | No restrictions, all capabilities available |
PoE 802.3af | enabled | All capabilities available (features may be disabled per |
IPM configuration)
PoE 802.3af| disabled| USB disabled
The 500 Series access points support a deep-sleep mode to deliver significant power and cost savings.
Before You Begin
Refer to the sections below before beginning the installation process.
FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
Pre-Installation Checklist
Before installing your Aruba 500 Series access point, be sure that you have
the following (not included with the AP):
- A mount kit compatible with the AP and mount surface
- Cat5E or better UTP cable with network access
- One or more external antennas (when using the AP-504)
- (Optional) a compatible 12V AC-to-DC power adapter with power cord
- (Optional) a compatible PoE midspan injector with power cord
- (Optional) a compatible snap-on front cover (for easy aesthetic customization)
- (Optional) an AP-CBL-SERU console cable Also make sure that (at least) one of the following network services is supported:
- Aruba Discovery Protocol (ADP)
- DNS server with an “A” record
- DHCP Server with vendor-specific options
The Aruba 500 Series access point is designed in compliance with governmental requirements so that only authorized network administrators can change the settings. For more information about access point configuration, refer to the AP Software Quick Start Guide.
Identifying Specific Installation Locations
Use the access point placement map generated by Aruba RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/ interference sources will impact RF propagation and should be accounted for during the planning phase and adjusted for in RF plan.
Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
Identifying Known RF Absorbers/Reflectors/Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in
the field during the installation phase is critical. Make sure that these
sources are taken into consideration when you attach an access point to its
fixed location.
RF absorbers include:
-
Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals.
-
Natural Items—Fish tanks, water fountains, ponds, and trees
-
Brick
RF reflectors include: -
Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.
-
Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances.
RF interference sources include: -
Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)
-
Cordless headset such as those used in call centers or lunch rooms
Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the performance of this equipment could result.
RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches (35cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Access Point Installation
the Aruba 500 Series access points are designed for ceiling or wall mounted
deployments. Several optional mount kits are available to attach the Aruba 500
Series access point to a variety of surfaces. These mount kits are available
as accessories and must be ordered separately. Refer to the online ordering
guide at http://www.arubanetworks.com/assets/og/OG_AP-500Series.pdf
All Aruba access points should be professionally installed by an Aruba- Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Failure to properly install this product may result in physical injury and/or damage to property.
The installer is responsible for securing the access
point onto the ceiling tile rail. Failure to properly install this product may
result in physical injury and/or damage to property.
Use of accessories, transducers and cables other than
those specified or provided by the manufacturer of this equipment could result
in increased electromagnetic emissions or decreased electromagnetic immunity
of this equipment and result in improper operation.
Software
For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick Start Guide.
Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in your country, refer to the Aruba Downloadable Regulatory Table at support.arubanetworks.com.
Verifying Post-Installation Connectivity
The integrated LED on the access point can be used to verify that the access point access point is receiving power and initializing successfully (see Table 1-Table 2). Refer to the AP Software Quick Start Guide for further details on verifying post-installation network connectivity.
Electrical and Environmental Specifications
For additional specifications on this product, please refer to the product
data-sheet at www.arubanetworks.com
Electrical
- Ethernet:
- E0 port: 10/100/1000BaseT auto-sensing MDI/MDX wired RJ45 network connectivity port
- Power:
- 12V DC power interface, support powering through AC-to-DC power adapter (AP-AC-12V30B)
- Power over Ethernet (PoE): 802.3af or 802.3at compliant source
If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an output rated 12V DC, minimum 0.75A, marked “LPS” and “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada.
Environmental
- Operating:
- Temperature: 0°C to +50°C (+32°F to +122°F)
- Humidity: 5% to 93% non-condensing
- Storage and transport:
- Temperature: -40°C to +70°C (-40°F to +158°F)
- Humidity: 5% to 93% non-condensing
The Aruba 500 Series access points are for indoor use
only. The access point, AC adapter, and all connected cables are not designed
for outdoor use.
This device is intended for stationary use in partly
temperature-controlled weather-protected environments.
Regulatory Model Name
The following regulatory model numbers (RMN) apply to the 500 Series:
- AP-504 RMN: APIN0504
- AP-505 RMN: APIN0505
Safety and Regulatory Compliance
RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches (35cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Federal Communication Commission
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio or TV technician for help.
Industry Canada
This Class B digital apparatus meets all of the requirements of the Canadian
Interference-Causing Equipment Regulations. In accordance with Industry Canada
regulations, this radio transmitter and receiver may only be used with an
antenna, the maximum type and gain of which must be approved by Industry
Canada. To reduce potential radio interference, the type of antenna and its
gain shall be chosen so that the equivalent isotropic radiated power (EIRP)
does not exceed the values necessary for effective communication. This device
complies with Industry Canada’s license-exempt RSS regulations. Operation of
this device is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation. When operated in
the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use
to reduce the potential for harmful interference with co-channel Mobile
Satellite Systems.
Canadian Caution
This radio transmitter model APIN0504/APIN0505 has been approved by Industry
Canada to operate with the antenna types listed in the table in the online
ordering guide (link provided below) with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use with
this device. http://www.arubanetworks.com/assets/og/OG_AP-500Series.pdf
European Union Regulatory Conformance
The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU
is available for viewing at:
www.hpe.com/eu/certificates. Select the
document that corresponds to your device’s model number as it is indicated on
the product label
This radio transmitter model has been approved to operate with the antenna types listed in the online ordering guide (link provided below) with the maximum permissible gain indicated. Antenna types not included in this list, having a greater gain than the maximum gain indicated for the type, are strictly prohibited for use with this device. Compliance is only assured if Aruba-approved accessories as listed in the ordering guide are used. http://www.arubanetworks.com/assets/og/OG_AP-500Series.pdf
Wireless Channel Restrictions 5150-5350MHz band is limited to indoors only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK).
Radio | Frequency Range MHz | Max EIRP |
---|---|---|
BLE/Zigbee | 2402-2480 | 9 dBm |
Wi-Fi | 2412-2472 | 20 dBm |
5150-5250 | 23 dBm | |
5250-5350 | 23 dBm | |
5470-5725 | 30 dBm | |
5725-5850 | 14 dBm |
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Instant User Guide for details on restrictions.
Medical
- Equipment not suitable for use in the presence of flammable mixtures.
- Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1.
- Wipe with a dry cloth, no additional maintenance required.
- No serviceable parts, the unit must be sent back to the manufacturer for repair.
- No modifications are allowed without Aruba approval.
This device is intended for indoor use in professional healthcare
facilities.
This device has no IEC/EN60601-1-2 essential performance.
Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
Compliance is based on the use of Aruba approved accessories.
Refer to the ordering guide for this access point at
http://www.arubanetworks.com/assets/og/OG_AP-500Series.pdf.
Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and result in improper operation.
Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the performance of this equipment could result.
Contact Aruba
Main Site | https://www.arubanetworks.com |
---|---|
Support Site | https://support.arubanetworks.com |
Airheads Social Forums and Knowledge Base |
https://community.arubanetworks.com/
North America Telephone| 1-800-943-4526
1-408-754-1200
International Telephone| https://www.arubanetworks.com/support-services
/contact-support/
Software Licensing Site| https://www.hpe.com/networking/support
End-of-Life Information| https://www.arubanetworks.com/support-services/end-
of-life/
Security Incident Response Team (SIRT)| https://www.arubanetworks.com
/support-service/security-bulletins/
Email: aruba-sirt@hpe.com
Copyright
© Copyright 2019 Hewlett Packard Enterprise Development LP
Open Source Code
This product includes code licensed under the GNU General PublicLicense, the
GNU Lesser General Public License, and/or certain other open source licenses.
A complete machine-readable copy of the source code corresponding to such code
is available upon request. This offer is valid to anyone in receipt of this
information and shall expire three years following the date of the final
distribution of this product version by Hewlett Packard Enterprise Company.
To obtain such source code, send a check or money order in the amount of US
$10.00 to:
Hewlett Packard Enterprise Company
Attn: General Counsel
6280 America Center Drive
San Jose, CA 94089
USA
Warranty
This hardware product is protected by an Aruba warranty. For more details,
visit www.hpe.com/us/en/support.html
Specifications
Product Specifications
|
Description
---|---
Model
|
Aruba 500 Series AP-505 Campus Access Points
Wireless Functionality
|
Concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi functionality with MIMO radios (2×2 in 2.4 GHz, 2×2 in 5 GHz), supporting legacy 802.11a/b/g/n/ac wireless services
Network Environments
|
Controller-based (ArubaOS) and controllerless (Aruba Instant)
Additional Radios
|
Bluetooth Low Energy (BLE) and Zigbee radio for locationing and IoT services
Mounting
|
Requires a mount kit (sold separately)
Package Contents
|
Aruba 500 Series access point (with a pre-installed mount bracket)
External Antenna Connectors
|
Two external antenna connectors for approved antennas only
LED Display Settings
|
Normal mode, Off mode, Blink mode
Ports
|
Console port (Micro-B connector), Ethernet port (10/100/1000Base-T auto- sensing MDI/MDX), USB 2.0 interface (USB-A port)
Reset Button
|
Used to reset access point to factory default settings or turn off/on LED display
Power
|
PoE-in (AP is a PoE-PD device) or proprietary AP-AC-12V30B power adapter (sold separately)
Intelligent Power Monitoring (IPM)
|
Used to manage power consumption preferences
Operational Restrictions
|
Dependent on power source and IPM configuration
Pre-Installation Checklist
|
Requires mount kit, Cat5E or better UTP cable, external antennas (when using AP-504), and optional power adapter, PoE midspan injector, snap-on front cover, and console cable
Network Services
|
Requires support for at least one network service
FAQS
Are these us or rw?
Complete scammers! They don’t work in the US
Does it come with the license ?
No. If you are seeing up a virtual controller them no license is needed. If you are going with the hardware controller then you will need to license appropriately.
Is this the R2H29A model?
Yes SIR
I s this (US)?
Yes, US unified
How do I find my Aruba access point model?
To view the Access Point Details page, follow these steps: Tap the Inventory( ) tile on the Aruba Instant On home page or tap the Site Health( ) banner and then tap Show inventory. Tap any of the APs listed in the Inventory list. The Access Point Details page is displayed with details.
What is the difference between the AP-504 and the AP-505?
The AP-504 and the AP-505 are identical except that the AP-505 also supports 802.11ax.
Are there any other differences between the AP-504 and the AP-505?
Yes, they have different default SSIDs. The default SSID for the AP-504 is “arubanetworks” and the default SSID for the AP-505 is “arubanetworks_ax”.
What are some of the differences between 802.11ax and 802.11ac?
802.11ax provides a number of improvements over 802.11ac, including higher throughput, lower latency, and higher density support in a single radio. For more information about these improvements, see Appendix A, “802.11ax Features.”
Can I use an AP-504 or an AP-505 in my network today?
Yes, you can use either an AP-504 or an AP-505 in your network today as long as you have a controller that supports 802.11ax (such as ArubaOS 6.4 or later). If you do not have a controller that supports 802.11ax, you will need to upgrade to one before you can use an AP-505 in your network. For more information about upgrading your controller to support 802.11ax, see Appendix B, “Upgrading Your Controller.”
Can I use an AP-504 or an AP-505 in my network if I do not have a controller?
Yes, you can use either an AP-504 or an AP-505 in your network if you do not have a controller by using Aruba Instant (controllerless) mode with Aruba Instant Cloud Services . For more information about Aruba Instant mode and Aruba Instant Cloud Services, see Appendix C, “Aruba Instant Overview.”
What are some of the differences between Aruba Instant mode and controllerless mode?
There are several differences between Aruba Instant mode and controllerless mode including how they handle security policies (Aruba Instant handles security policies at Layer 2 while controllerless mode handles security policies at Layer 3), how they handle authentication (Aruba Instant uses MAC address authentication while controllerless mode uses username/password authentication), how they handle mobility (Aruba Instant uses Layer 2 mobility while controllerless mode uses Layer 3 mobility), and how they handle roaming (Aruba Instant uses Layer 2 roaming while controllerless mode uses Layer 3 roaming). For more information about these differences, see Appendix C, “Aruba Instant Overview.”
Is Aruba access point good?
Access point Aruba is very reliable, efficient and stable. In the organization, we use the IAP version, which does not require a physical controller. All access points are managed from the central AirWave server, which also monitors devices and wifi networks.
What is the default IP address of Aruba access point?
The default IP address of the managed device is 172.16. 0.254/24. Connect a PC or workstation to any line port on the managed device, then enter this IP address into a supported Web browser to launch the Setup Wizard.
How does Aruba get internet?
With Wi-Fi Aruba you can get high-speed wireless internet access on your laptop, tablet or smartphone at several hotspots on the island, including restaurants, resorts, bars and even on the beach. You can access the Wi-Fi Aruba service using a Wi-Fi prepaid card or your Credit Card.
Is Aruba a router?
Aruba Instant On access points replace a typical router. Just plug an Aruba Instant On access point into the cable that brings the internet into your home to enable your Wi-Fi network.
What is the Aruba 500 Series AP-505 Campus Access Point?
The Aruba 500 Series AP-505 Campus Access Point is a high-performance, dual- radio wireless device that can be deployed in both controller-based (ArubaOS) and controllerless (Aruba Instant) network environments. It delivers reliable and fast wireless connectivity with concurrent 2.4 GHz and 5 GHz 802.11ax Wi- Fi functionality, MIMO radios, and support for legacy wireless services. It also comes equipped with a Bluetooth Low Energy (BLE) and Zigbee radio, enabling locationing and IoT services.
What is included in the package contents of the Aruba 500 Series Access Point?
The package contents include the Aruba 500 Series access point with a pre- installed mount bracket. The AP mount bracket attaches to a variety of mount kits (sold separately).
Can external antennas be installed on the Aruba 500 Series Access Point?
Yes, external antennas can be installed on the Aruba 500 Series Access Point. However, they must be installed by an Aruba Certified Mobility Professional (ACMP) or another Aruba-certified technician, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain.
What are the LED display settings for the Aruba 500 Series Access Point?
The LEDs have three operating modes that can be selected in the system management software: normal mode, off mode, and blink mode. Normal mode refers to Table 1 and Table 2 for LED status information.
What is the purpose of the Bluetooth Low Energy and Zigbee radio on the Aruba 500 Series Access Point?
The Bluetooth Low Energy and Zigbee radio on the Aruba 500 Series Access Point provide capabilities for location beacon applications, wireless console access, and IoT gateway applications.
What is the purpose of the console port on the Aruba 500 Series Access Point?
The console port is a Micro-B connector located on the back of the Aruba 500 Series Access Point. It is used for direct local management and requires a proprietary serial adapter cable (APCBL-SERU) to connect to a serial terminal or a laptop.
What is the purpose of the Kensington lock slot on the Aruba 500 Series Access Point?
The Kensington lock slot provides additional physical security for the Aruba 500 Series Access Point.
What is the purpose of the USB 2.0 interface on the Aruba 500 Series Access Point?
The USB 2.0 interface on the top of the Aruba 500 Series Access Point is compatible with selected cellular modems and other peripherals. When active, it can supply up to 5W/1A to a connected device.
How do I reset the Aruba 500 Series Access Point to factory default settings?
There are two ways to reset the Aruba 500 Series Access Point to factory default settings. The first way is to press and hold down the reset button using a small, narrow object such as a paper clip for more than 10 seconds during normal operation. The second way is to press and hold down the reset button using a small, narrow object such as a paper clip while the access point is not powered on (either via DC power or PoE), then connect the power supply (DC or PoE) to the access point while the reset button is being held down.
What are the power options and operational restrictions for the Aruba 500 Series Access Point?
The Aruba 500 Series Access Point supports PoE-in (AP is a PoE-PD device), allowing the device to draw power from compliant PoE power sources. If PoE is not available, a proprietary AP-AC-12V30B power adapter (sold separately) can be used to power the access point. When both PoE and DC power sources are available, the DC power source takes precedence. In the event that the DC source fails, the access point switches to the PoE sources. The Intelligent Power Monitoring (IPM) feature may also be used to manage the power consumption preferences for this device.
VIDEO
[www.arubanetworks.com](https://www.arubanetworks.com/)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>