WMF Lineo 4 in 1 Stickblender Instruction Manual

: June 3, 2024
: WMF

Table of Contents

Lineo 4 in 1 Stickblender
Important safety information
Use
Start-up
Cleaning and care
For the UK use only
Documents / Resources

Operating Manual
Stick blender 4-in-1

Lineo 4 in 1 Stickblender

WMF Lineo 4 in 1 Stickblender - 1

Design of blender

1. Swivel (speed setting)
2. On button
3. Turbo button
4. Release knob (reverse)| 5. Puree rod
6. Protective cap
7. Measuring jug with anti-slip base
---|---

Accessory set

8. Upper part with integrated adapter
9. Container
10. Stainless steel knife
11 . Anti-slip base| 12. Adapter
13. Whisk
14. Milk frother
---|---

Important safety information

The accessory and device can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
The accessory and device shall not be used by children. The accessory, device, and connecting cable are to be kept away from children.
Children should be supervised in order to ensure that they do not play with the accessory and devices.
The device is always to be disconnected from the mains by disconnecting the power plug when there is no supervision present or if there is a fault during operation, prior to assembly, disassembly, or cleaning.
Use caution when handling the accessories and device. It is essential to wait for the moving parts to stop before changing the attachments.
Use caution when handling the sharp cuttings blades as well as when emptying the bowl and when cleaning.
After using the accessory and device, clean all surfaces/parts that came into contact with food. Please follow the instructions in the chapter “Cleaning and care.”
If the appliance’s connection cable is damaged then it must be replaced by the manufacturer’s central customer service department or by a similarly qualiﬁed person. Improper repairs may constitute a serious threat to users.
This appliance is intended to be used in households and similar applications such as
- staff kitchen areas in shops, ofﬁces, and other working environments;
- farm houses; ⋅ by clients in hotels, motels, and other residential-type environments;
- bed and breakfast type environments.
  The appliance is not designed for sole commercial use.

Before use

Read the operating manual carefully. It contains important information about the use, safety and maintenance of the appliance. It should be kept in a safe place and passed on to further users if appropriate. The appliance should only be used for the intended purpose and in accordance with this user manual. Respect these safety instructions when using the appliance.
Technical data

Rated voltage:
Power consumption:
Protection class:| 220-240 V~ 50-60 Hz
590-700 W
II
---|---

Additional safety instructions

Connect the appliance to an alternating current only, with voltage in accordance with that shown on the appliance‘s type label. The wire and plug must be dry.
Never disconnect the mains plug from the socket by the cord or with wet hands.
Only switch the blender on once it has been placed in the food to be blended. Only remove from the food once the appliance has come to a stop.
Do not immerse the drive unit in water/foodstuff.
The device, accessory, and connection cable should be protected from the effects of heat.
If the appliance becomes blocked during use, switch it off immediately and remove the offending object, for example, a piece of fruit or vegetable which has become stuck. ▪ Allow hot food/liquids to cool to approximately 80°C (measuring cup (7)) before processing. Attention! There is a risk of scalding when handling hot food/liquids.
Stop using the device and accessory and/or disconnect the mains plug immediately if
- The appliance or mains cable is damaged
- There is any suspicion of a fault after dropping the appliance or similar. In such cases, send the appliance to be repaired.
Do not use the device and accessories outdoors.
No liability is accepted for damages resulting from misuse, incorrect operation, improper repairs or the use of accessories not designed for this appliance. Claims under warranty are likewise excluded in such cases.

Use

The immersion blender can be used to blend soft fruit and cooked vegetables or to prepare baby food or purees. The accessory is suited for crushing and mixing food, frothing milk or for whipping. Detailed application possibilities for the individual accessory parts can be found in the chapter “Start-up.” Any other use or excessive use is not considered proper. Observe the safety instructions during use.
In the case of misuse, improper operation, non-observance of the instructions for use, or unprofessional repairs, no liability will be assumed for any damages. Claims under warranty are likewise excluded in such cases.

Start-up

Please clean all parts described in the “Cleaning and care” section before allowing them to come into contact with food.
Purée rod

The immersion blender (5) can be used to blend soft fruit and cooked vegetables or to prepare baby food or purees. Large items should be roughly chopped beforehand.

Prepare the desired foodstuff and place it in a receptacle that is sufﬁciently large, tall, and stable, such as the container (7) provided. Use the anti-slip base to ensure a secure standing position.
Note: When chopping carrots or similar foodstuff only ﬁll in a container maximum of 600 ml.
Caution! The container (7) provided is not heat resistant. The maximum temperature it can withstand is 80°C. Allow boiled foodstuffs to cool somewhat before beginning. Do not use a container (7) for storing food.
Make sure that the appliance is disconnected from the power supply.
Attach the blender (5) stem at the bottom of the drive unit coupling and press together with the drive unit until you hear an audible click from the blender (5) meaning that it is locked in place. There should not be any gap between the driver unit and the blender (5). The blender (5) must be held ﬁrmly in the appliance and should not wobble or fall out. If necessary, turn the shaft of the purée rod (5) when pressing on the drive unit. The purée rod (5) must audibly click onto the drive unit and lock.
Choose the desired speed setting using the rotary swivel (1) on the top of the appliance.
Hold the blender (5) in the foodstuff.
Caution: spattering is likely when using the appliance. To avoid any spattering, the lower end of the blender (5) blades should always be entirely covered. For liquid foodstuffs, the appliance should always be held at a slight angle for improved blending. If using hot foodstuffs, be careful not to hold the appliance in the steam to avoid any condensation forming on the drive unit. If necessary, protect the drive unit and your hands from hot steam with a small, clean kitchen towel. Wipe any condensation off the housing immediately.
Now connect the mains plug to the socket. max.
Hold the appliance ﬁrmly in one hand and press the on switch (2) ****. The motor will begin to operate.
As soon as your foodstuff has reached the desired consistency, and after a maximum of one minute, release the on switch (2) ****. Alternatively, you can also press the turbo button (3), which will increase the speed of the appliance.
Wait until the motor and the gadgets have come to a stop, then remove the blender (5) from the appliance. Always remove the mains plug from the socket before placing the appliance on a suitable surface.

Chopper
With the chopper, you can chop and mince, onions, fruit, vegetables, hard cheese, herbs, nuts, and meat.

Remove the protective cover from the knife. Place the stainless steel knife (10) into the receptacle at the bottom of the container (9). Turn the stainless steel knife (10) until it slides to the bottom of the receptacle.
Attention: The blades are sharp. For this reason, always replace the protective cover when the blades are not in use. Place the food in the container (9) so that it is no higher than the MAX marking and place the upper part with the integrated adapter (8) on top. For better stability, attach the rubber anti-slip base (11) to the bottom of the container (9).
Attention: Fill with a maximum of 200ml of thin liquid food.
Insert the drive unit of the hand-held blender on the adapter (8) integrated into the upper part. Press the coupling of the drive unit onto the adapter (8) until the container (9) with the upper part audibly clicks into place and is therefore locked. There may be no gap between the drive unit and the adapter (8).
Use the rotary ring (1) to select the desired speed. Use a higher speed for harder food.
After connecting the mains plug, press the on ****switch (2) in multiple short bursts until you achieve the desired result. Hold the container (9) with one hand during the process. Alternatively, you can also press the turbo button (3) to process. The device then operates at full speed.
Once the desired result is achieved, wait until the motor and knife stop and disconnect the mains plug.
Loosen the upper part from the drive unit by pressing the unlock button (4). You can then remove the upper part (8) from the container (9) and carefully remove the knife.
Do not use a container (9) for storing food.

Milk frother
With the milk frother, you can froth milk, e.g. for cappuccinos, latte macchiatos, or even desserts.

Attach the adapter (12) by inserting it into the milk frother (14) with light pressure. The adapter (12) audibly clicks into place.
Attach the adapter (12) down onto the coupling of the drive unit and push it against the drive unit until the milk frother (14) audibly clicks onto the drive unit and is therefore locked. There may be no gap between the drive unit and the adapter (12). The milk frother (14) must sit ﬁrmly on the device and should not be loose or fall off.
Pour milk into a container with a high rim and insert the milk frother (14) into this container.
Use the rotary ring (1) to select the desired speed. After connecting the mains plug, push and hold the on-switch (2) ****until the desired result is achieved. Alternatively, you can also press the turbo button (3) to process. The device then operates at full speed.
Move the milk frother (14) in slight circular movements. As soon as the foam rises, move the milk frother (14) upwards so that it is always working just below the surface.
Once the desired result is achieved, wait until the motor and milk frother (14) stop and disconnect the mains plug.
Loosen the adapter (12) from the drive unit by pressing the unlock button (4). Pull the adapter (12) away from the milk frother (14).

Whisk
With the whisk you can, for example, prepare beaten egg whites, whip cream or shakes, desserts, soups, sauces, or mayonnaise.

Attach the adapter (12) by inserting it into the whisk (13) with light pressure. The adapter (12) audibly clicks into place.
Attach the adapter (12) down onto the coupling of the drive unit and push it against the drive unit until the whisk (13) audibly clicks onto the drive unit and is therefore locked. There may be no gap between the drive unit and the adapter (12). The whisk (13) must sit ﬁrmly on the device and should not be loose or fall off.
Put the ingredients into a suitable container and insert the whisk (13).
Use the rotary ring (1) to select the desired speed.
After connecting the mains plug, push and hold the on-switch (2) ****until the desired result is achieved.
Alternatively, you can also press the turbo button (3) to process. The device then operates at full speed.
Once the desired result is achieved, wait until the motor and whisk (13) stop and disconnect the mains plug.
Loosen the adapter (12) from the drive unit by pressing the unlock button (4). Pull the adapter (12) away from the whisk (13).

Cleaning and care

Disconnect the mains plug immediately after use.
Always clean the blender (5) immediately after use to prevent dried-on leftovers from damaging the bearing of the blender (5).
For preliminary cleaning, let the blender run for a short period of time in a receptacle containing hot water.
The blender (5) is locked into the appliance during use and can only be removed by pressing the release button (4). The blender (5) can now be removed.
For safe storage, put the purée rod (5) in the protective cap (6).
Clean the accessory immediately after use so that dried-on residual food cannot damage the accessory.
Do not use any abrasive cleaning agents.

| Dishwasher safe| Can be rinsed under running
water| Wipe with a damp cloth
---|---|---|---
Drive unit| | |
Purée rod (5)| | |
Protective cap (6)| | |
Measuring jug with anti-slip base (7)| | |
Upper part with an integrated adapter| | |
Container (9)| | |
Stainless steel knife (10)| | |
Anti-slip base (11)| | |
Adapter (12)| | |
Whisk (13)| | |
Milk frother (14)| | |

For the UK use only

This product is supplied with a 13 A plug conforming to BS 1363 ﬁtted to the mains lead. If the plug is unsuitable for your socket outlets or needs to be replaced, please note the following. If the plug is a non-rewireable one, cut it from the mains lead and immediately dispose of it. Never insert it into a socket outlet as there is a very great risk of an electric shock.
The replacement of the plug at the mains lead has to be done according to the following instructions:
Important: The wires in this mains lead are coloured in accordance with the following code:blue
brown| Neutral
Live
---|---

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

  * the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black,
  * the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

Do not connect any wire to the terminal which is marked with the letter E or by the earth symbol , or coloured green or green and yellow.

If a 13 A (BS 1363) plug is used it must be ﬁtted with a 3 A fuse conforming to BS 1362 and be ASTA-approved. If any other type of plug is used, the appliance must be protected by a 5 A fuse either in the plug or adapter or at the distribution board. If in doubt – consult a qualiﬁed electrician.
Never use the plug without closing the fuse cover.

The appliance complies with European directives 2014/35/EU, 2014/30/EU and 2009/125/EU.
The conformity according to EN60335 clause 11 was veriﬁed by using a chopper accessory and the following recipe: 210g ﬂour + 100g water + 40g honey Short Operation Time: 3s; Resting 10 minutes between cycles
At the end of its life, this product may not be disposed of in normal household waste, but must instead be taken to a collection point for recycling electrical and electronic appliances.
The materials are recyclable in accordance with their labelling. Reuse, recycling and other ways of reutilising old appliances make an important contribution to protecting our environment.
Please ask your local authorities for information about the appropriate disposal point.
End users are personally responsible for deleting any personal data that may be stored on appliances they are disposing of. Subject to change.

C onsumer Service:
Tel.: +49 (0)7331 256 256
E-Mail:contact-de@wmf.com
Hersteller:
WMF GmbH
WMF Platz 1
73312 Geislingen/ Steige
Germany
wmf.com
Änderungen vorbehalten – IB-1635 0011-06-2205
Modell 0416350011**
consist of:
1x 0416120011
1x 0416980071**

Documents / Resources

| WMF Lineo 4 in 1 Stickblender [pdf] Instruction Manual
Lineo 4 in 1 Stickblender, Lineo, 4 in 1 Stickblender, Lineo Stickblender, Stickblender
---|---