DS18 RZR-GBSUB10LD 10 Inch Loaded Subwoofer Enclosure Owner’s Manual
- June 1, 2024
- DS18
Table of Contents
DS18 RZR-GBSUB10LD 10 Inch Loaded Subwoofer Enclosure
10″ LOADED SUBWOOFER ENCLOSURE FOR POLARIS RZR GLOVE BOX
FEATURES
- DURALE POLYETHYLENE (PE) BOX
- 2 CORE 2 FEET (650 MM) INPUT SPEAKER WIRE
- THIS RZR-SUB BOX COMES WITH A 10″ 1200 WATT WATER RESISTANT SUBWOOFER
- MOUNTING BRACKET AND HARDWARE INCLUDED
- UV PROTECTED
INSTALLATION
Please refer to your owners manual for disassembly and reassembly of your vehicle.
- Turn the hood locks, and remove the hood. Extract the (4) T40 torx screws and extract the (2) push pins from the dash. From inside the machine, pull the dash towards you and lift it to unclip. Once unclipped remove the dash cap.
- Remove one (1) T40 Torx screw located directly above the left footrest on the passenger side.
- Install the large hardware bracket on the subwoofer enclosure using one bolt as pictured. Hand-tighten so the bracket can slide left to right.
- With the bracket to the left install the subwoofer box in the glovebox location.
- Hang the subwoofer enclosure from the T-handle mounting bar as shown by sliding the installed bracket over the bar.
GENERAL SPECIFICATIONS
- Nominal Diameter ……………………………………………………………………………….10″ / 254mm
- Nominal Impedance …………………………………………………………………………………. 2 Ohms
- RMS Power Handling …………………………………………………………………………… 600W
- MAX Power Handling ………………………………………………………………………….1200W
- Sensitivity (1w/1m) ………………………………………………………………………………….. 92dB
- Frequency Response …………………………………………………………………. 25Hz-250Hz
- Recommended Hi Pass Crossover ………………………………………………. 120Hz
BODY FEATURES
- Enclosure Material …………………………………………. Polyethylene (PE) / Polietileno (PE)
- Marine Grade Type ………………………………………………………………………………………..IPX5
- Sold in Pair or Single ………………………………………………………….Single / Soltero
- Color ………………………………………………………………………………………………………………………..Black / Negro
- Port Plug Cover ………………………………………….. Yes (Rubber) / Sí (Caucho)
- Direct OEM Fit …………………………………………………………………………………………….Yes / Si
WOOFER SPECIFICATIONS / ESPECIFICACIONES DEL WOOFER:
- Voice Coil Diameter …………………………………………………………….. 2″ / 50.8mm
- VC Former Material …………………….. Black Aluminum / Aluminio Negro
- Winding Material ………………………………………………………………………………………. SV
- Cone Material …………………………………………………..Non-Pessed Paper/ Papel no pegado
- Dust Cap Material ……………………………………. Carbon Fiber / Fibra de Carbon
- Surround Material ………………………………………………………………… Rubber / Goma
- Basket Material ……………………………………………………………………………… Steel / Acero
- Magnet Material ………………………………………………………………………………..Ferrite / Ferrita
- Magnet Weight ………………………………………………………………………………………………………81 Oz
THIELE & SMALL PARAMETERS / PARÁMETROS T/S:
- Equivalent Volume ……………………..Vas…………………………………….. 23.67L / 0.835ft3
- Excursion ……………………………………………………..Xmax …………………………………………………… 21mm
- Free Air Resonance …………………Fs …………………………………………………………..37Hz
- Mechanical Factor ……………………………..Qms…………………………………………………………5.07
- Electrical Factor …………………………………..Qes ………………………………………………………….0.76
- Total Factor ………………………………………………Qts …………………………………………………………..0.66
- Moving Mass ……………………………………….Mms…………………………………………………. 140.16g
- Compliance …………………………………………….Cms ……………………………………………… 0.13mm/N
- BL Factor / Factor Bl ………………………………………………………Bl……………………………………………………………..9.26
- Voice Coil Inductance……..Le ……………………………………………………….0.38mH
- Diaphragm Area ……………………………………..Sd………………………………………………….352.99cm2
- DC Resistance ………………………………………Re………………………………………………….. 2.01 ohms
BOX MEASUREMENT / MEDIDA DE CAJA:
- Overall Height / Altura Total……………………………………………………………………………………………..16.9″ / 430mm
- Overall Depth / Profundidad Total…………………………………………………………………………………. 14.17″ / 360mm
- Overall Wide / Ancho Total……………………………………………………………………………………………….16.9″ / 430mm
- Extract the (4) T40 screws surrounding the ride command system and (2) push pins found in the dash pocket. *For non-ride command vehicles, less hardware may need to be removed for this step. Unclip the dash surrounding the glovebox. Once unclipped, gently pull the dash forward and remove the upper dash pocket.
- Extract the (1) T40 torx that secures the lower dash pocket.
- Disconnect the USB and unclip the LED from the lower dash pocket. Remove the lower dash pocket. Label / take photos of the harnesses connected to the dash. Once recorded, disconnect the harnesses, and remove the dash.
- With the dash removed, extract the (2)10mm bolts retaining the glovebox and remove the glovebox.
- Install the remaining screws and hand tighten.
- Install the supplied screw in the lower mounting hole aligning with the factory hole in the footwell and tighten the screws from steps 6 ,7 and 10.
- Feed speaker wire into dash towards amplifier mounting location. Reassemble steps 1. to 4. and enjoy your new audio experience.
RZR KIT FIT GUIDE
RZR kits are compatible with the following RZR models
- Not Compatible with Pro XP/ Pro R Model RZR’s or existing factory audio systems.
- Non-RC RZR models must have dash dry box, Polaris part number 5439789-070, for dash mount kit to work
MEASUREMENTS
WARRANTY
Please visit our website DS18.com for more information on our warranty policy. We reserve the right to change products and specifications at any time without notice. Images may or may not include optional equipment.
WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov
FOR MORE INFORMATION PLEASE VISIT DS18.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>