winees M3 Plus Security and Outdoor Camera Instructions

winees M3 Plus Security and Outdoor Camera

IN THE BOX

PRODUCT OVERVIEW

1. Mic
2. Light Sensor
3. Light Indicator
4. IR LED
5. Spotlight (only in M3Plus)
6. Reset Button
7. MicroSD Card Slot

APP SETUP

1. Scan the OR code below to download the AiDot APP.
   Or search for”AiDot” in App Store or Google Play

2. Power on the camera, yOu will hear “Waiting for Wi-Fi configuration” with the camera’s indicator light flashing in green.

3. In the AIDot app, press’+- select Winees M3Plus/M3 Cam the instructions on App.

4. Place the M3Plus or M3 Cam in the area where you plan to install to test the video quality, ensure that the camera can work normally after the final installation.

INSTALLATION

• Install on the wall
  For a better user experience, we recommend you to install the camera as the below conditions.

• On a masonry surface (3M tape can be used to fix the position before screw driven in)

• On a wooden surface(3M tape can be used to fix the position before screw driven in)

• Install on the ceiling (3M tape can be used to fix the position before screw driven in)

• Place on the table or other flat surface (3M tape can be used to fix the position)

LIGHT INDICATIONS

CAUTIONS

To avoid personal injury and/or possible product damage, the following cautions must be followed:

1. Please use the provided adapter instead of others in case of any damage to the product
2. Keep out of reach of children. This product contains small magnets and other small parts, which can cause choking or injury if ingested.
3. To prevent early failure, the camera should only be Installed in operating environments ranging between -20°C 50°C(-4°F~ 122°F).
4. Do not install
   • close to heat source
   • near the metal objects and mirrors that cause radio Signal attenuation shadin9.
5. Do not disassemble or reinstall the camera, otherwise, it may cause security risks.
6. Unplug the power cord before cleaning. Do not clean the camera with any liquids, spray cleaner or wet cloth.
7. The slot and opening are used for ventilation, not allowed to be blocked or covered.
8. This product only can be connected to 2.4G WIFL.

FCC Statement

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following twO conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received including interference that may cause undesired operation.
   Note: The grantee is not responsible for any changes or modifications not expressly approved by the party, responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
   Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
   This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
   However, there is no guarantee that interference will not OCCur in a particular installation. If this equipment does cause harmful interference to radio or teleVisIon reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

3. Reorient or relocate the receiving antenna.

4. Increase the separation between the equipment and receiver.

5. Connect the equipment intO an outlet on a circuit different from that to which the receiver is connected.

6. Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

ISED Statement
This device contains license-exempt transmitter (s) /receiver(s) that comply with InnOvation, Science and Economic Development Canada’s license-exempt RSS(S). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>