winees WP0500187 Water Leak Sensor Hub User Manual

winees WP0500187 Water Leak Sensor Hub User Manual

Product Profile

The Water Leak Sensor utilizes the conductivity of water. When two probes touch the water simultaneously, a current loop is formed. At this time, the sensor reports the water immersion/water leakage status to the hub, triggering an alarm or linking other smart devices to perform related actions.

It’ll be notified via the app or text message included with purchased value- added services, whether at home or outside.
*915NlHz is a frequency band of wireless communication technology.

Hub Wi-Fi pairing button: after pressing and holding for 5s, the hub is ready for Wi-Fi connection.

915 pairing button: after a long press for 3s, connect the water leak sensor to the hub.

Reset button: press and hold for 10s to reset the hub. LED indicator: shows the status of the hub.

Water leak sensor

Water detection probes: detect water leakage Press and hold the button: send a pairing signal Battery: CR2450 button battery.

Package Contents

1. After pressing the button for 1s, the water leak sensor indicator “flashes red” once, indicating that it is working normally. If not, please open the back cover with a professional tool or a coin and replace it with a new battery.
   

2. If the water leak sensor is placed on a leaking surface, the hub alarm will be triggered.
   

3. Press any button on the hub. Take the water leak sensor out of the water and wipe it down to stop the alarm completely.
   
   Note: The app will push a low battery prompt when the battery is low.

Installation

1. Plug the hub into the power.
2. Lay the water leak sensor flat.
   Note: Keep the distance between the hub and the water leak sensor less than 100m/328ft.
   

Before Installation

1. Support 2.4GHz (does not support 5GHz) and 802.11b/ g/n band routers.
   Note: most 5GHz routers can be set to 2.4GHz band or dual band.

2. Make sure the Wi-Fi name and password are correct.

3. Support a 2.4GHz phone or tablet.

4. Download the AiDot app from the App Store (iOS devices) or Google Play (Android devices).

Connect to Wi-Fi Network

1. Connect the phone to the 2.4GHz network.
   Note: Android device users need to turn on the location function, and iOS users need to click Settings on the phone> AiDot> Location> Always.

2. Open AiDot, click “+” in the upper right corner, and select SI Plus in the Hub list.
   

3. Press and hold the hub Wi-Fi pairing button for 5s. The hub is ready to connect to Wi-Fi when the indicator flashes blue.
   

4. Follow the app’s instructions to complete the connection.

5. Successfully connected to Wi-Fi, the indicator stays on blue. You can find the water leak sensor in the list of devices.
   Note: If you can’t find the water leak sensor, please swipe down the device list page to refresh or add the water leak sensor by referring to “Add or re-add the water leak sensor” below.
   

6. If it cannot connect to Wi-Fi, the blue light will go out.
   

Please check the above steps and try again;or you can select ”S1 Plus”in the app and tap”Video Guide”for more instruction.

Notification Settings

App notifications: Open the app and select “Water Leak Detector”in the devi¢e list. Tap the settings icon in the upper right corner to turn on/off the notification sound.

Add or re-add the water leak sensor

Note: When the hub successfully connects to Wi-Fi for the first time, the water leak sensor has been connected to the hub by default.

1. Press and hold the 915MHz pairing button for 3s. The hub is waiting for the sub-device to connect when the green light flashes quickly.
   
   Press and hold this button for 3s

2. Place the water leak sensor the hub. When the button is  pressed, the sensor will send a pairing signal to the hub.

3. The hub is receiving the signal.
   

4. The hub is paired with the water leak sensor.

5. Swipe down to refresh the device list page in the app to find the new device.

Notice:

• If the hub fails to pair with the sensor within the 30s, its indicator light will flash green quickly and exit pairing mode.
• After pressing the button of the water leak sensor, the red indicator light flashes once.
• If pairing fails, please check the above steps and try again.

Troubleshooting

1. The hub cannot connect to Wi-Fi / the connection is unstable.
   a. 5GHz network is not supported. It only supports 2.4GHz.
   b. Check that the Wi-Fi name and password are correct.
   c. Place the hub within the coverage area of the router’s signal.
   d. It is recommended that there are no obstacles such as metal doors or walls between the hub and the water leak sensor.

2. The water leak sensor does not work.
   a. Please install the battery before use.
   b. Use a coin to open the battery cover and reinstall the battery.
   c. Please check if the battery is low.

3. There is no push/delay push in the app.
   a. Android users need to turn on the location feature, and iOS users need to tap Settings on the phone> AiDot > Location > Always.
   b. Keep the distance between the hub and water leak sensor as close as possible.
   c. Make sure there are no obstructions between the hub and the water leak sensor.
   d. The time interval between leakage detections should be greater than the 60s. Otherwise, the app will not push notifications.
   e. Check if the hub indicator flashes when the water leak sensor is triggered. If not, please re-add the water leak sensor.

Battery replacement

The detector does not have batteries installed by default. Please install the CR2450 battery to use.

Installation steps:

• A. Unscew the battery cover and inser the battery.

• B. Screw on the battery cover and replace the base.

Warning:

1. Keep the working temperature of the device within the range of 32°F-140°Fand the humidity below 90%RH.
2. Do not disassemble the device violently.

Specifications

Hub

• Voltage: AC 1J0-240V 50/60Hz
• Wi-Fi Frequency: 2.4GHz
• Wi-Fi-enabled Distance: 60m/197ft

Water leak sensor

• Voltage: DC 3V
• Working Distance (No obstructions): 100m/328ft
• Wireless frequency: FSK915MHz
• Waterproof rating: IP66

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Readjust or reposition the receiving antenna.
2. Increase the distance between the equipment and the receiver.
3. Connect the device and receiver to different sockets.
4. Consult the dealer or an experienced radio/TV technician for assistance.

FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. When installing and operating this equipment, keep a distance of at least 20 cm between the radiator and your body.

Customer Service

iwiness is a trademark of Linkzone Technology Co., Limited. Copyright  belongs to Linkzone Technology Co., Limited.

Warning:
Risk of explosion if an incorrect type replaces battery. Dispose of used batteries according to the instructions.

Warranty: 12 months warranty
After Sales Support: Lifetime Technical Support
Email: support@iwinees.com
Website: www.iwinees.com
@Aidot @Aidot @pAidot @Aidot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>